Home › Engine / Hybrid System › 1HZ (ENGINE CONTROL) › ECD SYSTEM
RM25T0E _51 Engine / Hybrid System _029759 1HZ ENGINE CONTROL _0135351 ECD SYSTEM J

1HZ ENGINE CONTROL  ECD SYSTEM  ECU Power Source Circuit  


DESCRIPTION

When the ignition switch is turned to ON, positive battery voltage is applied to the coil, supplying power to terminal +B of the emission control ECU.

WIRING DIAGRAM

A225217E02
1.542,2.052 1.688,2.229 0.146,0.177 10 false 4 1.719,2.635 2.156,2.813 0.438,0.177 10 false L21 1.719,2.802 2.635,2.979 0.917,0.177 10 false Ignition Switch 5.51,0.615 5.688,0.792 0.177,0.177 10 false 25 5.823,0.708 6.01,0.885 0.188,0.177 10 false +B 5.51,3.5 5.688,3.677 0.177,0.177 10 false 14 5.833,3.604 6.021,3.781 0.188,0.177 10 false E1 5.677,4.5 6.01,4.677 0.333,0.177 10 false A30 5.677,4.667 7.156,4.844 1.479,0.177 10 false Emission Control ECU 0.979,2.302 1.281,2.479 0.302,0.177 10 false AM1 4.625,0.813 5.188,0.99 0.563,0.177 10 false ECU-IG 3.604,1.344 4,1.531 0.396,0.188 10 false IG1 1 1.458,0.875 2.177,1.042 0.719,0.167 10 false AM1 NO.2 0.677,2.833 0.958,3.021 0.281,0.188 10 false ALT 0.656,3.531 1.24,3.688 0.583,0.156 10 false FL MAIN 1.573,4.385 2.052,4.552 0.479,0.167 10 false Battery 0.344,4.844 0.51,4.99 0.167,0.146 10 false *1 1.385,4.083 1.563,4.229 0.177,0.146 10 false *2 2.563,4.917 3.844,5.115 1.281,0.198 10 false *1: for 12 V Battery 2.563,5.219 3.844,5.417 1.281,0.198 10 false *2: for 24 V Battery 2.375,2.26 2.656,2.427 0.281,0.167 10 false IG1 1.75,2.25 2.052,2.427 0.302,0.177 10 false AM1 3.323,0.583 3.479,0.771 0.156,0.188 10 false 3 4.125,0.594 4.292,0.781 0.167,0.188 10 false 5 3.323,0.906 3.438,1.083 0.115,0.177 10 false 1 4.125,0.896 4.24,1.094 0.115,0.198 10 false 2 2.719,2.042 2.854,2.219 0.135,0.177 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT EMISSION CONTROL ECU (+B VOLTAGE)
a.
A190329C19
1.24,1.25 1.792,1.583 0.552,0.333 1.229,1.948 0.792,2.656 true 1.823,1.948 1.906,2.656 true 0.292,0.292 1.469,0.833 1.177,0.542 10 false *a 0.552,2.667 1.063,2.865 0.51,0.198 10 false 25 (+B) 1.74,2.688 2.26,2.885 0.521,0.198 10 false 14 (E1) 1.406,1.333 1.74,1.5 0.333,0.167 10 false A30
*a Rear view of wire harness connector
(to Emission Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A30-25 (+B) - A30-14 (E1) Ignition switch ON 11 to 14 V*1
22 to 28 V*2


*1: for 12 V battery

*2: for 24 V battery


Result:
Proceed to
OK
NG




OK

NG

2.CHECK HARNESS AND CONNECTOR (EMISSION CONTROL ECU - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (EMISSION CONTROL ECU - BODY GROUND)
a.

Disconnect the emission control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-14 (E1) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (IG1 1 RELAY - EMISSION CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IG1 1 RELAY - EMISSION CONTROL ECU)
a.

Remove the IG1 1 relay from the cowl side relay block assembly.


b.

Disconnect the emission control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG1 1 relay terminal (5) - A30-25 (+B) Always Below 1 Ω
IG1 1 relay terminal (5) or A30-25 (+B) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

4.INSPECT RELAY (IG1 1)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT RELAY (IG1 1)
a.

Remove the IG1 1 relay from the cowl side relay block assembly.


b.
A186036

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 No battery voltage is applied to terminals 1 and 2 10 kΩ or higher
3 - 5 Battery voltage is applied to terminals 1 and 2 Below 1 Ω


Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR (IG1 1 RELAY - BATTERY, BODY GROUND)

NG

REPLACE RELAY (IG1 1)

5.CHECK HARNESS AND CONNECTOR (IG1 1 RELAY - BATTERY, BODY GROUND)
a.

Remove the IG1 1 relay from the cowl side relay block assembly.


b.
A226765C01
0.229,0.5 0.615,0.688 0.385,0.188 10 false *1 2.427,1.99 2.823,2.146 0.396,0.156 10 false *2
*1 COWL SIDE RELAY BLOCK ASSEMBLY
*2 IG1 1 Relay


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
IG1 1 relay terminal (3) - Body ground Ignition switch ON 11 to 14 V*1
22 to 28 V*2


*1: for 12 V battery

*2: for 24 V battery



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG1 1 relay terminal (2) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

6.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - IG1 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (IGNITION SWITCH ASSEMBLY - IG1 1 RELAY)
a.

Remove the IG1 1 relay from the cowl side relay block assembly.


b.

Disconnect the ignition switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
IG1 1 relay terminal (1) - L21-1 (IG1) Always Below 1 Ω
IG1 1 relay terminal (1) or L21-1 (IG1) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

7.INSPECT IGNITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>1HZ (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION SWITCH ASSEMBLY - BATTERY)

NG

REPLACE IGNITION SWITCH ASSEMVLY