Home › Engine / Hybrid System › 1HZ (ENGINE CONTROL) › ECD SYSTEM
RM25T0E _51 Engine / Hybrid System _029759 1HZ ENGINE CONTROL _0135351 ECD SYSTEM J

1HZ ENGINE CONTROL  ECD SYSTEM  Back-up Power Source Circuit  


DESCRIPTION

Positive battery voltage is supplied to terminal BATT of the emission control ECU even when the ignition switch is off for use by the diagnostic trouble code memory, etc.

WIRING DIAGRAM

A225222E02
4.188,0.802 4.635,0.979 0.448,0.177 10 false ECU-B 5.448,1.615 5.75,1.813 0.302,0.198 10 false A30 5.792,0.646 6.219,0.823 0.427,0.177 10 false BATT 5.667,2.188 7.125,2.365 1.458,0.177 10 false Emission Control ECU 5.781,1.615 5.969,1.792 0.188,0.177 10 false E1 5.458,0.667 5.719,0.844 0.26,0.177 10 false A31 5.531,0.448 5.688,0.625 0.156,0.177 10 false 1 5.479,1.417 5.656,1.594 0.177,0.177 10 false 14 2.427,0.813 2.979,0.979 0.552,0.167 10 false MAIN1 0.99,0.813 1.583,1.01 0.594,0.198 10 false FL MAIN 1.729,1.604 2.208,1.771 0.479,0.167 10 false Battery 0.49,2.198 0.656,2.344 0.167,0.146 10 false *1 1.542,1.302 1.719,1.448 0.177,0.146 10 false *2 1.99,2.125 3.271,2.323 1.281,0.198 10 false *1: for 12 V Battery 1.99,2.427 3.271,2.625 1.281,0.198 10 false *2: for 24 V Battery 4.073,0.552 4.219,0.729 0.146,0.177 10 false 1 4.594,0.552 4.729,0.729 0.135,0.177 10 false 2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT EMISSION CONTROL ECU (BATT VOLTAGE)
a.
A190329C20
1.24,1.25 1.792,1.583 0.552,0.333 1.906,1.25 2.458,1.583 0.552,0.333 2.302,1.875 2.615,2.458 true 1.823,1.958 1.594,2.667 true 0.365,0.375 0.854,0.771 0.49,0.396 10 false *a 2.406,2.51 3.052,2.708 0.646,0.198 10 false 1 (BATT) 1.365,2.719 1.885,2.917 0.521,0.198 10 false 14 (E1) 1.396,1.333 1.729,1.5 0.333,0.167 10 false A30 2.052,1.333 2.375,1.5 0.323,0.167 10 false A31
*a Rear view of wire harness connector
(to Emission Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A31-1 (BATT) - A30-14 (E1) Always 11 to 14 V*1
22 to 28 V*2


*1: for 12 V battery

*2: for 24 V battery


Result:
Proceed to
OK
NG




NG

2.CHECK HARNESS AND CONNECTOR (EMISSION CONTROL ECU - BODY GROUND)

OK

4.INSPECT BATTERY
2.CHECK HARNESS AND CONNECTOR (EMISSION CONTROL ECU - BODY GROUND)
a.

Disconnect the emission control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A30-14 (E1) - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

3.CHECK HARNESS AND CONNECTOR (ECU-B FUSE - EMISSION CONTROL ECU, ECU-B FUSE - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ECU-B FUSE - EMISSION CONTROL ECU, ECU-B FUSE - BATTERY)
a.

Check harness and connector between the ECU-B fuse and emission control ECU.

i.

Remove the ECU-B fuse from the cowl side relay block assembly.


ii.

Disconnect the emission control ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ECU-B fuse (2) - A31-1 (BATT) Always Below 1 Ω
ECU-B fuse (2) or A31-1 (BATT) - Body ground Always 10 kΩ or higher




b.

Check the harness and connector between the ECU-Bfuse and battery.

i.

Remove the ECU-B fuse from the cowl side relay block assembly.


ii.

Disconnect the positive battery terminal cable.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Battery positive terminal - ECU-B fuse (1) Always Below 1 Ω
Battery positive terminal or ECU-B fuse (1) - Body ground Always 10 kΩ or higher




Result:
Proceed to
OK
NG



OK

4.INSPECT BATTERY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT BATTERY
a.

Check that the battery is not depleted.

OK:

Battery is not depleted.



Result:
Proceed to
OK
NG



OK

5.CHECK EMISSION CONTROL ECU

NG

REPLACE BATTERY

5.CHECK EMISSION CONTROL ECU
a.

Check if DTCs are stored even after turning the ignition switch off.

OK:

DTCs are stored.



Result:
Proceed to
OK
NG



OK

NG