Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM › 2014.08–2017.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0135360 ECD SYSTEM U

1VD-FTV ENGINE CONTROL  ECD SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS's Data List allows switch, sensor, actuator, and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch OFF.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch ON.


e.

Turn the GTS ON.


f.

Enter the following menus: Powertrain / Engine and ECT / Data List.

HINT:

To display the entire Data List, press the pull down menu button next to Primary. Then select All Data.




Engine Control


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed Min.: 0 km/h, Max.: 255 km/h Actual vehicle speed Speed indicated on speedometer
Target Idle Engine Speed Target engine speed Min.: 0 rpm, Max.: 5000 rpm - -
Engine Speed Engine speed Min.: 0 rpm, Max.: 16383.75 rpm Idling: 500 to 600 rpm -
Calculate Load Calculated load by ECM Min.: 0%, Max.: 100%
·

Idling: 15.4 to 20.4%

·

Running without load (2500 rpm): 20.1 to 25.9%


-
MAF Air flow rate from MAF meter status Min.: 0 gm/sec., Max.: 655.35 gm/sec.
·

Idling: 6.1 to 26.5 gm/sec.

·

Running without load (2000 rpm): 28.2 to 130 gm/sec.


If value approximately 0 gm/sec.:
·

Mass air flow meter power source circuit open

·

VG circuit open or shorted


If value 240 gm/sec. or more:
EVG circuit open
Atmosphere Pressure Atmospheric pressure value Min.: 0 kPa, Max.: 255 kPa Actual atmospheric pressure -
MAP Absolute pressure inside intake manifold Min.: 0 kPa, Max.: 255 kPa
·

Idling: 90 to 102 kPa

·

Engine running at 3000 rpm: 100 to 150 kPa


-
Coolant Temp Engine coolant temperature Min.: -40°C, Max.: 140°C After warming up engine: 75 to 90°C (167 to 194°F) If value is -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
Intake Air Intake air temperature Min.: -40°C, Max.: 140°C Equivalent to temperature at intake manifold If value is -40°C (-40°F) or 140°C (284°F), sensor circuit open or shorted
Intake Air Temp (Turbo) Intake air temperature Min.: -40°C, Max.: 190°C 70°C (158°F) or less -
Engine Run Time Engine run time Min.: 0 sec., Max.: 65535 sec. Time after engine started Service data
Initial Engine Coolant Temp Initial engine coolant temperature Min.: -40°C, Max.: 120°C Engine coolant temperature when engine started -
Initial Intake Air Temp Initial intake air temperature Min.: -40°C, Max.: 120°C Intake air temperature when engine started -
Battery Voltage Battery voltage Min.: 0 V, Max.: 65.535 V 11 to 14 V -
Alternate Duty Ratio Alternator generation duty ratio Min.: 0%, Max.: 100%
·

No electrical load at idling:

20 to 60%

·

High electrical load at idling:

100%


·

This is outputs the alternator generation duty and is used to determine the electrical load.

·

Can be used to determine whether a higher-than-normal injection volume at idle, etc. is due to electrical loading or from some other source. For example, when the duty is not high but the idling injection volume is high, there is injector volume degradation or high engine friction.

·

Can be used for judging whether or not a malfunctioning component in the electrical system is generating continual generation requests (e.g., battery deterioration is causing an unending full recharge request, etc.). Regardless of whether or not an auxiliary device like the A/C or heater is active, if the alternator duty is always at the maximum value, there is an electrical system abnormality, like battery deterioration.


Pre Glow Pre-glow operation ON or OFF - This is the ECM command.
After Glow After-glow operation ON or OFF - This is the ECM command.
Accel Position Accelerator position status Min.: 0%, Max.: 100%
·

Accelerator pedal released:

0%

·

Accelerator pedal depressed:

100%


Read value with ignition switch ON (do not start engine)
Accel Sens. No.1 Volt % Acceleratorposition No. 1 Min.: 0%, Max.:100%
·

Accelerator pedal released:

10 to 22%

·

Accelerator pedal fully depressed:

52 to 90%


Read value with ignition switch to ON (do not start engine)
Accel Sens. No.2 Volt % Acceleratorposition No. 2 Min.: 0%, Max.:100%
·

Accelerator pedal released:

24 to 40%

·

Accelerator pedal fully depressed:

68 to 99%


Read value with ignition switch to ON (do not start engine)
Starter Signal Starter signal ON or OFF ON: Cranking -
Power Steering Signal Power steering signal ON or OFF ON: Power steering operation This signal status usually ON until ignition switch turned OFF
Power Steer. Sig. Record Power sttering signai record ON or OFF - -
Low Gear Switch Low gear switch signal ON or OFF - -
Clutch Switch First position switch ON or OFF ON: First position -
Stop Light Switch Stop light switch signal ON or OFF
·

ON: Brake pedal depressed

·

OFF: Brake pedal released


-
A/C Signal A/C signal ON or OFF ON: A/C ON -
Immobiliser Communication Immobiliser communication ON or OFF ON: Normal -
Check Mode Check mode ON or OFF ON: Check mode on The mode in which certain DTCs can be detected more easily and with higher sensitivity.
SPD Test Result Check mode result for vehicle speed sensor Compl or Incompl - Check mode result for the vehicle speed sensor.
# Codes(Include History) Number of codes Min.: 0, Max.: 255 - Number of DTCs appearing at least once during the last 40 times the vehicle was warmed up.
MIL MIL status ON or OFF OFF: MIL off -
MIL ON Run Distance Distance traveled with MIL on Min.: 0 km
Max.: 65535 km
Distance traveled after DTC stored
·

Distance traveled after a DTC is stored.

·

Cleared when the cable is disconnected from the negative (-) battery terminal, or when the DTC is cleared using the intelligent tester.


Running Time from MIL ON Running time after MILturns on Min.: 0 km
Max.: 65535 km
Running time after MILturns on
·

Engine run time since the MIL illumination.

·

Cleared when the cable is disconnected from the negative (-) battery terminal, or when the DTC is cleared using the intelligent tester.


Time after DTC Cleared Time after DTC cleared Min.: 0 min., Max.: 65535min. Equivalent to time after DTCs were erased -
Distance from DTC Cleared Distance after DTC cleared Min.: 0 km, Max.: 65535 km Equivalent to drive distance after DTCs were erased -
Warmup Cycle Cleared DTC Warmup cycle after DTC cleared Min.: 0, Max.: 255 - Number of warmup cycles after DTC cleared
OBD Requirements Identifying OBD requirement - - -
Number of Emission DTC Number of emissions-related DTCs - - -
TC and TE1 Connect the TC and TE1 status for Active Test ON or OFF - Active Test support date
Engine Start Time Engine start time Min.: 0 ms, Max.: 267000 ms - Service data
ACT VSV A/C cut status for Active Test ON or OFF - Active Test support date

Compression


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed of Cyl #1 Engine speed for No. 1 cylinder Min.: 0 rpm, Max.: 51199 rpm Engine speeds of all cylinders almost same
·

Output only when the "Check the Cylinder Compression" Active Test is performed.

·

Indicates the speed of each cylinder when cranking.

Example - Normal: Engine speeds of all cylinders are approximately equal.

When No. 1 cylinder compression is low, "Engine Speed of Cyl #1" is approximately 300 rpm, and "Engine Speed of Cyl #2 to #8" is approximately 200 rpm.


Symptoms when out of range:
When the engine speeds of all cylinders are not equal, idling will be rough.
Cause of Out of Range:
Cyl #1 compression goes down
Engine Speed of Cyl #2 Engine speed for No. 2 cylinder Min.: 0 rpm, Max.: 51199 rpm Engine speeds of all cylinders almost same -
Engine Speed of Cyl #3 Engine speed for No. 3 cylinder Min.: 0 rpm, Max.: 51199 rpm Engine speeds of all cylinders almost same -
Engine Speed of Cyl #4 Engine speed for No. 4 cylinder Min.: 0 rpm, Max.: 51199 rpm Engine speeds of all cylinders almost same -
Engine Speed of Cyl #5 Engine speed for No. 5 cylinder Min.: 0 rpm, Max.: 51199 rpm Engine speeds of all cylinders almost same -
Engine Speed of Cyl #6 Engine speed for No. 6 cylinder Min.: 0 rpm, Max.: 51199 rpm Engine speeds of all cylinders almost same -
Engine Speed of Cyl #7 Engine speed for No. 7 cylinder Min.: 0 rpm, Max.: 51199 rpm Engine speeds of all cylinders almost same -
Engine Speed of Cyl #8 Engine speed for No. 8 cylinder Min.: 0 rpm, Max.: 51199 rpm Engine speeds of all cylinders almost same -
Av Engine Speed of All Cyl Engine speed for all cylinders Min.: 0 rpm, Max.: 51199 rpm -
·

Output only when the Active Test "Check the Cylinder Compression" is performed.

·

Indicates the average engine speed of all cylinders during cranking.



Vehicle Information


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Model Code Model code - - -
Engine Type Engine type - - Identifying engine type: 1VD-FTV
Cylinder Number Cylinder number Min.: 0, Max.: 255 - Identifying cylinder number: 8
Transmission Type Transmission type MT or ECT - MT (Manual transmission)
Destination Destination - - -
Model Year Model year Min.: 1900, Max.: 2155 - Identifying model year: 20##
System Identification System identification - - Identifying engine type: Diesel

Diesel Injection


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Injection Volume Injection volume Min.: 0 mm3/st, Max.: 1279.98 mm3/st Idling: 3.0 to 10 mm3/st -
Inj. FB Vol. for Idle Idle stability status integral control volume Min.: -80 mm3/st, Max.: 79 mm3/st -10 to 10 mm3/st
·

When the actual engine speed does not match the target idling speed, this corrects the injection volume.

If this item displays 10 mm3/st or more or -10 mm3/st or less even with the engine completely warmed up and the air conditioning and other electrical loads off, the internal parts of the engine may be damaged, or the fuel injection system or other auxiliary components may be malfunctioning.

·

Only calculated and reflected at idle.


Inj Vol Feedback Learning Injection volume feedback learning value Min.: -10 mm3/st, Max.: 9.92 mm3/st - -
Injection Feedback Val #1 Injection volume correction for No. 1 cylinder Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 8 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Injection Feedback Val #2 Injection volume correction for No. 2 cylinder Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 8 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Injection Feedback Val #3 Injection volume correction for No. 3 cylinder Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 8 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Injection Feedback Val #4 Injection volume correction for No. 4 cylinder Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 8 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Injection Feedback Val #5 Injection volume correction for No. 5 cylinder Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 8 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Injection Feedback Val #6 Injection volume correction for No. 6 cylinder Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 8 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Injection Feedback Val #7 Injection volume correction for No. 7 cylinder Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 8 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Injection Feedback Val #8 Injection volume correction for No. 8 cylinder Min.: -10 mm3/st, Max.: 10 mm3/st Idling: -3.0 to 3.0 mm3/st
·

When idling after warmup, the injection amount for each cylinder is corrected to optimize the difference between the engine speed of each cylinder.

Example: For cylinders that are slowing the engine speed compared to other cylinders, the injection volume is increased.

·

"Injection Feedback Val" more than 3.0 mm3/st: Injector breakdown is causing injection volume deviation, or insufficient compression is causing poor combustion.

·

Even if "Injection Feedback Val" for a cylinder is less than -3.0 mm3/st, the cylinder with this value does not necessarily have a problem.

HINT:
·

The ECM adjusts each cylinder so that the average "Injection Feedback Val" of the 8 cylinders is approximately 0 mm3/st.

·

If more than one cylinder has a positive correction value, a normal cylinder may have a value less than -3.0 mm3/st.




Pilot 1 Injection Period Pilot 1 injection period Min.: 0 μs, Max.: 65535 μs Idling: 135 to 279 μs Check to see if "Pilot 1 Injection Period" is not zero when symptoms occur.
Pilot 2 Injection Period Pilot 2 injection period Min.: 0 μs, Max.: 65535 μs Idling: 113 to 312 μs Check to see if "Pilot 2 Injection Period" is not zero when symptoms occur.
Main Injection Period Main injection period Min.: 0 μs, Max.: 65535 μs -
·

When the fuelpressure becomes15000 kPa or less,"Main InjectionPeriod" is set to 0.

·

When the engine will not start, confirm that injection is performed.

·

When P0093, P0627 or P0200 is stored, there is an engine stall request. At that time, "Main Injection Period" equals 0.

HINT:

As the engine stalls 1 minute after the MIL illuminates, freeze frame data cannot be checked.



After Injection Period After injection period Min.: 0 μs, Max.: 65535 μs - Check to see if "After Injection Period" is not zero when the following symptoms occur: Black smoke, poor driveability.
Pilot 1 Injection Timing Pilot 1 injection timing Min.: -70 deg(CA), Max.: 20 deg(CA) Idling after engine warmed up and vehicle is under normal atmospheric pressure: 0 deg(CA) -
Pilot 2 Injection Timing Pilot 2 injection timing Min.: -50 deg(CA), Max.: 20 deg(CA) Idling after engine warmed up and vehicle is under normal atmospheric pressure: -1.4 to -5.4 deg(CA) -
Main Injection Timing Main injection timing Min.: -90 deg(CA), Max.: 90 deg(CA) Idling after engine warmed up and vehicle is under normal atmospheric pressure: -0.5 to 2.5 deg(CA) Use "Main Injection Timing" to check poor drivability when the following symptoms are present: Bad injection timing, black smoke, and white smoke.
After Injection Timing After injection timing Min.: -10 deg(CA), Max.: 50 deg(CA) - -
Injector Memory Error Injector memory error No Error or Error No Error If the injectorcompensation codes arenot input into the newECM, or if a injectorcompensation code of adifferent injector model ora compensation coderepresenting a valuewhich exceeds thecompensation settingrange is input into thenew ECM, DTC P1601 isstored and "InjectorMemory Error" displays"Error".
Target Common Rail Pressure Target common rail pressure Min.: 0 kPa, Max.: 655350 kPa 25000 to 180000 kPa -
Fuel Press Fuel pressure Min.: 0 kPa, Max.: 655350 kPa Idling: 27000 to 37000 kPa -
Fuel Temperature Fuel temperature Min.: -40°C, Max.: 140°C Actual fueltemperature After fully cold soaking the engine, the fuel temperature is the same as the outside air temperature.
Fuel Return Temp Fuel return temperature Min.: -40°C, Max.: 140°C Idling after engine warmed-up: 35 to 85°C If the "Fuel Return Temp" value is not between 55°C (131°F) and 130°C (266°F), "Pilot Quantity Learning" is prohibited.
Target Pump SCV Current Final pump current target value Min.: 0 mA, Max.: 4000 mA Idling: 923 to 1123 mA
·

ECU-calculated value for the suction control valve actuation target current.

·

Value is large when a high fuel pressure is desired.

·

Normally, the value is between 800 and 2500 mA.

·

If the value is stuck at 3000 mA or higher, it indicates that the operation is poor (poor movement due to deposits, etc.).

·

When this deviates from the standard value, it indicates that for some reason, even though the pump is running hard, the actual fuel pressure is inconsistent with the target fuel pressure.


Idle Injection Volume (Min) Minimum fuel injection volume Min.: 0 mm3/st, Max.: 39.8 mm3/st 3 to 10 mm3/st Service data

EGR System


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Target EGR Pos. EGR valve target opening amount Min.: 0%, Max.: 100% Idling after engine warmed up: 0 to 65%
·

Fully open: 100%.

·

Fully closed: 0%.

·

Used for comparison to "Actual EGR Valve Pos.".


Target EGR Pos. #2 EGR valve target opening amount Min.: 0%, Max.: 100% Idling after engine warmed up: 0 to 65%
·

Fully open: 100%.

·

Fully closed: 0%.

·

Used for comparison to "Actual EGR Valve Pos #2.".


Actual EGR Valve Pos. Actual EGR valve position Min.: 0%, Max.: 100% Idling after engine warmed up: 0 to 83%
·

Fully open: 100%.

·

Fully closed: 0%.

·

Inspect while comparing to "Target EGR Valve Pos".

·

Check the valve movement via the Active Test.

·

Sometimes malfunctions only occur around a certain temperature, so refer to the engine coolant temperature and outside temperature at the time the malfunction occurred.


Actual EGR Valve Pos. #2 Actual EGR valve position Min.: 0%, Max.: 100% Idling after engine warmed up: 0 to 83%
·

Fully open: 100%.

·

Fully closed: 0%.

·

Inspect while comparing to "Target EGR Valve Pos #2".

·

Check the valve movement via the Active Test.

·

Sometimes malfunctions only occur around a certain temperature, so refer to the engine coolant temperature and outside temperature at the time the malfunction occurred.


EGR Lift Sensor Volt % EGR lift position Min.: 0%, Max.: 100% Idling: 0 to 80% -
EGR Lift Sensor Volt % #2 EGR lift position Min.: 0%, Max.: 100% Idling: 0 to 80% -
EGR Motor Duty #1 EGR valve actuation duty Min.: 0%, Max.: 127.5% Idling after engine warmed-up: 0 to 100%
·

This EGR Motor Duty #1 is calculated based on Target EGR Valve Pos. to actuate the No. 1 EGR valve assembly.

·

To 0%: Close side EGR valve actuation.

·

To 100%: Open side EGR valve actuation.

·

When this value is large but the actual valve position does not reach the target valve position, there is an unable to open malfunction.


EGR Motor Duty #2 EGR valve actuation duty Min.: 0%, Max.: 127.5% Idling after engine warmed-up: 0 to 100%
·

This EGR Motor Duty #2 is calculated based on Target EGR Valve Pos. to actuate the No. 2 EGR valve assembly.

·

To 0%: Close side EGR valve actuation.

·

To 100%: Open side EGR valve actuation.

·

When this value is large but the actual valve position does not reach the target valve position, there is an unable to open malfunction.


EGR Close Lrn. Val. EGR fully closed position learned value Min.: 0 V, Max.: 5 V 3.5 to 4.5 V
·

This value is the EGR position sensor output voltage.

·

When the value is at the upper or lower limit of the normal range, it is possible that a foreign object is lodged in the EGR valve seat area.

·

As the lower and upper limits are 3.5 V and 4.5 V respectively, if the value becomes stuck at either of these values, there is a malfunction in the lift sensor or the valve position may be misaligned (foreign matter is present, etc.).


EGR Close Lrn. Val. #2 EGR fully closed position learned value Min.: 0 V, Max.: 5 V 3.5 to 4.5 V
·

This value is the EGR position sensor output voltage.

·

When the value is at the upper or lower limit of the normal range, it is possible that a foreign object is lodged in the EGR valve seat area.

·

As the lower and upper limits are 3.5 V and 4.5 V respectively, if the value becomes stuck at either of these values, there is a malfunction in the lift sensor or the valve position may be misaligned (foreign matter is present, etc.).


EGR Close Lrn. Status EGR valve fully closed position learning status OK or NG OK
·

"OK" means the fully closed position learning has completed normally.

·

When NG, the learned fully closed position may be outside of the normal range.

When NG, there may be foreign matter stuck in the valve.


EGR Close Lrn. Status #2 EGR valve fully closed position learning status OK or NG OK
·

"OK" means the fully closed position learning has completed normally.

·

When NG, the learned fully closed position may be outside of the normal range.

When NG, there may be foreign matter stuck in the valve.


EGR Operation Prohibit EGR operation prohibition OK or NG OK: Possible to perform"Control the EGR Step Position" Active Test
·

OK: It is possible to perform the "Control the EGR Step Position" Active Test.

·

NG: It is not possible to perform the "Control the EGR Step Position" Active Test.



Diesel Throttle System


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Target Throttle Position Target throttle position Min.: -128%, Max.: 127%
·

Throttle valve fully opened:

0%

·

Throttle valve fully closed:

100%


If there is a malfunction of the throttle actuator, compare the target and actual throttle position values for troubleshooting.
Target Throttle Position #2 Target throttle position Min.: -128%, Max.: 127%
·

Throttle valve fully opened:

0%

·

Throttle valve fully closed:

100%


If there is a malfunction of the throttle actuator, compare the target and actual throttle position values for troubleshooting.
Actual Throttle Position Actual diesel throttle position Min.: -20%, Max.: 120% Idling after engine warmed-up:
5 to 100%
-
Actual Throttle Position #2 Actual diesel throttle position Min.: -20%, Max.: 120% Idling after engine warmed-up:
5 to 100%
-
Throttle Motor DUTY #1 Diesel throttle motor duty Min.: 0%, Max.: 100% - -
Throttle Motor DUTY #2 Diesel throttle motor duty Min.: 0%, Max.: 100% - -
Diesel Throttle Learn Status Diesel throttle learning history OK or NG OK
·

If the system is functioning properly, learning will be performed when the ignition switch is turned from on to off.

·

NG indicates that a foreign object may be lodged in the throttle valve or actuator components, or a disconnection/short exists in the signal wires.


Diesel Throttle Learn Status #2 Diesel throttle learning history OK or NG OK
·

If the system is functioning properly, learning will be performed when the ignition switch is turned from on to off.

·

NG indicates that a foreign object may be lodged in the throttle valve or actuator components, or a disconnection/short exists in the signal wires.


Throttle Sensor Volt % Absolute throttle position sensor (bank 1) Min.: 0%, Max.: 100% Ignition switch ON: 60 to 80%
Warmed-up and idling: 10 to 80%
-
Throttl Sensor #2 Volt % Absolute throttle sensor positioning (bank 2) Min.: 0%, Max.: 100% Ignition switch ON: 60 to 80%
Warmed-up and idling: 10 to 80%
-

VN Turbo System


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Target Booster Pressure Target booster pressure Min.: 0 kPa, Max.: 320 kPa Driving vehicle on level surface at 3000 rpm with full load:
150 to 250 kPa
·

Inspect while comparing with "MAP".

·

With the accelerator fully open, if the actual manifold absolute pressure (MAP) is low compared to the target booster pressure by at least 20 kPa for 5 sec. or more, a feeling of a lack of power will occur.

·

When the vehicle is driven with the engine speed at 3000 rpm or more and the accelerator pedal fully depressed, "MAP" is approximately equal to "Target Booster Pressure".


VN Turbo Command VN turbo command Min.: 0%, Max.: 100% 0 to 100% ECD freeze frame data
VN Turbo Type VN turbo type Not Avl, Commo, Vacuum, CAN Com or DC Commo Indicates the VN turbo vane actuation method.
·

DC motor system.

·

Negative-pressure diaphragm system.

·

Step motor system.


VN Turbo Max Angle VN turbo maximum opening amount Min.: 0%, Max.: 100% 100%
HINT:

As this value displays the ideal constant upper limit, no matter what happens, this value should not change.


·

The maximum vane opening amount is displayed in %.

·

The VN turbo is operated between VN Turbo Max Angle and VN Turbo Min Angle when the Test the Turbo Charger Step Motor Active Test is performed.


VN Turbo Min Angle VN turbo minimum opening amount Min.: 0%, Max.: 100% 0%
HINT:

As this value displays the ideal constant lower limit, no matter what happens, this value should not change.


·

The maximum vane opening amount is displayed in %.

·

The VN turbo is operated between VN Turbo Max Angle and VN Turbo Min Angle when the Test the Turbo Charger Step Motor Active Test is performed.



Diesel Starting


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Engine Speed (Starter Off) Engine speed when starter off Min.: 0 rpm, Max.: 1594 rpm - Service data
Starter Count Starter ON count Min.: 0, Max.: 255 - Service data
Run Dist of Previous Trip Distance driven during previous trip Min.: 0 km, Max.: 261 km - Service data

Diesel Rough


Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Electric Duty Feedback Value Electric load feedback value Min.: 0 mm3/st, Max.: 39.8 mm3/st 0 to 2 mm3/st Service data
A/C Duty Feedback Value A/C load feedback value Min.: 0 mm3/st, Max.: 39.8 mm3/st 0 to 2 mm3/st Service data
PS Duty Feedback Value Power steering load feedback value Min.: 0 mm3/st, Max.: 39.8 mm3/st 0 mm3/st Service data

ACTIVE TEST


HINT:

Performing the GTS's Active Test allows relay, VSV, actuator and other items to be operated without removing any parts. Performing the Active Test early in troubleshooting is one way to save time.

The Data List can be displayed during the Active Test.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch ON.


c.

Turn the GTS ON.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


e.

Perform the Active Test.

Powertrain > Engine and ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Control the A/C Cut Signal Control the A/C signal ON/OFF -
Connect the TC and TE1 Turn on TC and TE1 connection ON/OFF -
Control the EGR Step Position Control the EGR valve (bank 1) 0 to 100% Test possible when following conditions met:
·

Ignition switch ON

·

Engine is stopped


Control the EGR Step Position #2 Control the EGR valve (bank 2) 0 to 100% Test possible when following conditions met:
·

Ignition switch ON

·

Engine is stopped


Diesel Throttle Target Angle Control the diesel throttle valve (bank 1) 0 to 90% Test possible when following conditions met:
·

Ignition switch ON

·

Engine is stopped


Diesel Throttle Target Angle #2 Control the diesel throttle valve (bank 2) 0 to 90% Test possible when following conditions met:
·

Ignition switch ON

·

Engine is stopped


Test the Turbo Charger Step Motor Control the VRV for turbocharger 0 to 100%
·

Active Test available only while engine idling

·

Active Test only operates when value is 0%


Test the Fuel Leak Pressurizes common rail internal fuel pressure, and checks for fuel leaks Stop/Start
·

Fuel inside common rail pressurized to specified value and engine speed increased to 2000 rpm when Start is selected

·

Above conditions preserved while test is Start


Activate the VN Turbo Open Activate the turbocharger ON/OFF Confirm that the engine is running.
Activate the EGR Valve Close Activate electric vacuum regulating valve assembly ON/OFF Confirm that the vehicle is stopped and the engine is idling.
Control the Select Cylinder Fuel Cut Selected cylinder (cylinder #1 to #8) injector fuel cut
·

#1/#2/#3/#4/#5/#6/#7/#8

·

ON/OFF


Perform this test when the following conditions are met:
·

Confirm that the vehicle is stopped and the engine is idling.

·

If the running condition of the engine does not worsen even though injection of the designated cylinder is stopped, the cylinder can be determined to be malfunctioning.


Check the Cylinder Compression Check the cylinder compression pressure ON/OFF Fuel injection stops in all cylinders.*

*: In this Active Test, the fuel of all cylinders is cut, and cranking occurs for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is higher than the other cylinders, the compression pressure of that cylinder is determined to be lower than the other cylinders.

1.

Warm up the engine.

2.

Turn the ignition switch OFF.

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch ON and turn the GTS ON.

5.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

HINT:

If the results are not displayed normally, select the display items from the Data List before performing the Active Test. Enter the following menus: Powertrain / Engine and ECT / Data List / Compression / Engine Speed of Cyl #1, Engine Speed of Cyl #2, Engine Speed of Cyl #3, Engine Speed of Cyl #4, Engine Speed of Cyl #5, Engine Speed of Cyl #6, Engine Speed of Cyl #7, Engine Speed of Cyl #8 and Av Engine Speed of All Cyl.


6.

While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

HINT:

After performing the above procedure, the Active Test's Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited, and each cylinder's engine rpm measurement will enter standby mode.


7.

Crank the engine for about 10 seconds.

8.

Monitor the engine speed (Engine Speed of Cyl #1 to #8, Av Engine Speed of All Cyl) displayed on the GTS.

HINT:

At first, the GTS's display will show each cylinder's engine rpm measurement to be extremely high. After approximately 10 seconds of engine cranking, each cylinder's engine rpm measurement will change to the actual engine rpm.


NOTICE:
·

After the Active Test's Check the Cylinder Compression is turned ON, it will automatically turn OFF after 255 seconds.

·

When the Check the Cylinder Compression test is OFF and the engine is cranked, the engine will start.

·

If the Check the Cylinder Compression test needs to be performed after it is turned ON and performed once, press EXIT to return to the Active Test menu screen. Then perform the Check the Cylinder Compression test again.

·

Use a fully-charged battery.