Measure the voltage according to the value(s) in the table below.
The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated.
The result of the checks should be compared with the standard normal voltage for that pair of terminals, which is displayed in the Specified Condition column.
The illustration above can be used as a reference to identify the ECM terminal locations.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A29-20 (BATT) - C39-81 (E1) | R-B - BR | Battery (for measuring the battery voltage and for the ECM memory) | Always | 11 to 14 V |
| A29-28 (IGSW) - C39-81 (E1) | B - BR | Ignition switch | Ignition switch ON | 11 to 14 V |
| A29-2 (+B) - C39-81 (E1) | L - BR | Power source of ECM | Ignition switch ON | 11 to 14 V |
| A29-44 (MREL) - C39-81 (E1) | W-G - BR | MAIN relay (MAIN) | Ignition switch ON | 11 to 14 V |
| 10 seconds elapsed after ignition switch turned OFF | 0 to 1.5 V | |||
| C39-66 (VCPM) - C39-75 (E2) | L-R - BR | Power source of manifold absolute pressure sensor (for PIM) | Ignition switch ON | 4.5 to 5.5 V |
| C39-70 (VCM) - C39-75 (E2) | L-R - BR | Power source of fuel pressure sensor (for PCR1) | Ignition switch ON | 4.5 to 5.5 V |
| C39-90 (VCEG) - C39-87 (EEGL) | L-R - G-R | Power source of EGR valve position sensor | Ignition switch ON | 4.5 to 5.5 V |
| C39-91 (VCVL) - C39-92 (EVLU) | L-R - W-R | Power source of throttle position sensor | Ignition switch ON | 4.5 to 5.5 V |
| C39-72 (VG) - C39-118 (EVG) | L-Y - G-W | Mass air flow meter | Engine is warmed up: Idling, A/C switch OFF | 0.5 to 3.4 V |
| C39-71 (THA) - C39-75 (E2) | Y-B - BR | Intake air temperature sensor (built into mass air flow meter) | Engine is warmed up: Idling, intake air temperature at 0 to 80°C (32 to 176°F) | 0.5 to 3.4 V |
| C39-85 (VN) - C39-81 (E1) | L - BR | VRV (Vacuum regulating valve) | Idling | Pulse generation |
| A29-53 (VPA) - A29-57 (EPA) | L-R - W | Accelerator pedal position sensor (for engine control) | Ignition switch ON, accelerator pedal fully released | 0.6 to 1.0 V |
| Ignition switch ON, accelerator pedal fully depressed | 3.0 to 4.6 V | |||
| A29-54 (VPA2) - A29-58 (EPA2) | R-B - BR | Accelerator pedal position sensor (for sensor malfunction detection) | Ignition switch ON, accelerator pedal fully released | 1.4 to 1.8 V |
| Ignition switch ON, accelerator pedal fully depressed | 3.7 to 5.0 V | |||
| A29-55 (VCPA) - A29-57 (EPA) | BR-W - W | Power source of accelerator pedal position sensor (for VPA) | Ignition switch ON | 4.5 to 5.5 V |
| A29-56 (VCP2) - A29-58 (EPA2) | V - BR | Power source of accelerator pedal position sensor (for VPA2) | Ignition switch ON | 4.5 to 5.5 V |
| C39-74 (THIA) - C39-75 (E2) | W-G - BR | Intake air temperature sensor (after turbocharged) | Engine is warmed up: Idling, intake air temperature sensor (after turbocharged) at 0 to 80°C (32 to 176°F) | 0.5 to 3.4 V |
| C39-76 (THW) - C39-75 (E2) | G-B - BR | Engine coolant temperature sensor | Engine is warmed up: Idling, engine coolant temperature at 60 to 120°C (140 to 248°F) | 0.2 to 1.2 V |
| C39-40 (#1) - C39-81 (E1) | Y - BR | Fuel injector | Idling | Pulse generation (see waveform 1) |
| C39-39 (#2) - C39-81 (E1) | B - BR | |||
| C39-38 (#3) - C39-81 (E1) | L - BR | |||
| C39-37 (#4) - C39-81 (E1) | R - BR | |||
| C39-36 (#5) - C39-81 (E1) | G - BR | |||
| C39-35 (#6) - C39-81 (E1) | V - BR | |||
| C39-34 (#7) - C39-81 (E1) | W - BR | |||
| C39-33 (#8) - C39-81 (E1) | P - BR | |||
| C39-80 (G+) - C39-79 (G-) | W - B | Camshaft position sensor | Idling | Pulse generation |
| C39-78 (NE+) - C39-77 (NE-) | B - W | Crankshaft position sensor | Idling | Pulse generation |
| C39-114 (PIM) - C39-75 (E2) | P-L - BR | Manifold absolute pressure sensor | Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied | 0.1 to 0.7 V |
| Same as atmospheric pressure | 0.8 to 1.4 V | |||
| Positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) applied | 1.6 to 2.2 V | |||
| A29-45 (IREL) - C39-81 (E1) | P - BR | EDU relay (EDU 1) | Ignition switch OFF | 11 to 14 V |
| Idling | 0 to 1.5 V | |||
| A29-46 (IRL2) - C39-81 (E1) | R - BR | EDU relay (EDU 2) | Ignition switch OFF | 11 to 14 V |
| Idling | 0 to 1.5 V | |||
| C39-69 (PCR1) - C39-75 (E2) | B - BR | Fuel pressure sensor | Idling (Approximately 35 MPa (357 kgf/cm2, 5078 psi)) | 1.3 to 1.8 V |
| C39-63 (GREL) - C39-81 (E1) | R - BR | No. 1 glow relay | Cranking | 11 to 14 V |
| Idling | 0 to 1.5 V | |||
| C39-62 (GRL2) - C39-81 (E1) | L - BR | No. 2 glow relay | Cranking | 11 to 14 V |
| Idling | 0 to 1.5 V | |||
| C39-116 (THF) - C39-75 (E2) | G-R - BR | Fuel temperature sensor | Ignition switch ON | 0.5 to 3.4 V |
| C39-106 (PCV+) - C39-105 (PCV-) | W - BR | Suction control valve | Idling | Pulse generation (see waveform 2) |
| C39-61 (INJF) - C39-81 (E1) | W - BR | No. 1 injector driver | Idling | Pulse generation (see waveform 3) |
| C39-60 (INF2) - C39-81 (E1) | W - BR | No. 2 injector driver | Idling | Pulse generation (see waveform 3) |
| C39-93 (VLU) - C39-75 (E2) | L-W - BR | Throttle position sensor (for Bank 1) | Ignition switch ON (throttle valve fully opened) |
2.8 to 3.8 V |
| Idling (throttle valve fully closed) |
0.4 to 1.0 V | |||
| C39-103 (VLU2) - C39-75 (E2) | L-W - BR | Throttle position sensor (for Bank 2) | Ignition switch ON (throttle valve fully opened) |
2.8 to 3.8 V |
| Idling (throttle valve fully closed) |
0.4 to 1.0 V | |||
| C39-42 (LUSL) - C39-81 (E1) | B - BR | Diesel throttle duty signal (for Bank 1) | Engine warmed up, racing engine | Pulse generation |
| C39-84 (LUS2) - C39-81 (E1) | B - BR | Diesel throttle duty signal (for Bank 2) | Engine warmed up, racing engine | Pulse generation |
| C39-89 (EGLS) - C39-75 (E2) | R-W - BR | No. 1 EGR valve position sensor | Ignition switch ON | 3.0 to 4.6 V |
| C39-88 (EGS2) - C39-75 (E2) | R-W - BR | No. 2 EGR valve position sensor | Ignition switch ON | 3.0 to 4.6 V |
| C39-107 (EGRS) - C39-81 (E1) | R - BR | No. 1 EGR valve | Engine is warmed up: Idling | Pulse generation |
| C39-108 (ERS2) - C39-81 (E1) | R - BR | No. 2 EGR valve | Engine is warmed up: Idling | Pulse generation |
| A29-36 (STP) - C39-81 (E1) | W - BR | Stop light switch | Ignition switch ON, brake pedal depressed | 7.5 to 14 V |
| Ignition switch ON, brake pedal released | 0 to 1.5 V | |||
| A29-35 (ST1-) - C39-81 (E1) | R-L - BR | Stop light switch (opposite to STP) |
Ignition switch ON, brake pedal depressed | 0 to 1.5 V |
| Ignition switch ON, brake pedal released | 7.5 to 14 V | |||
| A29-15 (TACH) - C39-81 (E1) | B - BR | Engine speed | Idling | Pulse generation |
| A29-8 (SPD) - C39-81 (E1) | G - BR | Speed signal from combination meter | Ignition switch ON, wheel rotated slowly | Pulse generation |
| A29-48 (STA) - C39-81 (E1) | B-W - BR | Starter signal | Cranking | 6.0 V or more |
| C39-1 (ALT) - C39-81 (E1) | R - BR | Generator duty ratio | Idling | Pulse generation |
| A29-27 (TC) - C39-81 (E1) | G - BR | Terminal TC of DLC3 | Ignition switch ON | 11 to 14 V |
| A29-24 (W) - C39-81 (E1) | R-W - BR | MIL | MIL illuminated | 0 to 3 V |
| MIL not illuminated | 11 to 14 V | |||
| A29-19 (SIL) - C39-81 (E1) | W - BR | Terminal SIL of DLC3 | Connect GTS to DLC3 | Pulse generation |
| A29-23(GIND) - C39-81 (E1) | L-R - BR | GLOW indicator light | GLOW indicator light illuminated | 0 to 3 V |
| Idling | 11 to 14 V | |||
| A29-30 (AC1) - C39-81 (E1) | B-W - BR | A/C signal | A/C switch ON | 0 to 1.5 V |
| A/C switch OFF | 11 to 14 V | |||
| A29-18 (ACT) - C39-81 (E1) | L-B - BR | A/C signal | Ignition switch ON | 11 to 14 V |
| A/C cut control ON | 0 to 3 V | |||
| A29-12 (IUSW) - C39-81 (E1) | L-R - BR | Idle up switch | Idle up switch ON | 0 to 3 V |
| Idle up switch OFF | 11 to 14 V | |||
| C39-24 (RSW) - C39-81 (E1) | R-B - BR | Back up light switch | Ignition switch ON, shift position is reverse | 11 to 14 V |
| Ignition switch ON, shift position is not reverse | 0 to 3 V | |||
| A29-42 (CLSW) - C39-81 (E1) | P-B - BR | Clutch switch | Ignition switch ON, clutch pedal fully depressed | 0 to 3 V |
| Ignition switch ON, clutch pedal fully released | 11 to 14 V | |||
| C39-2 (PS) - C39-81 (E1) | P - BR | Power steering oil pressure switch | Steering wheel turned | 0 to 3 V |
| Steering wheel not turned | 11 to 14 V | |||
| C39-32 (FSW) - C39-81 (E1) | L-W - BR | Shift position switch | Ignition switch ON, shift position is first | 0 to 3 V |
| Ignition switch ON, shift position is not first | 11 to 14 V |
WAVEFORM 1
| ECM Terminal Name | Between #1 to #8 and E1 |
| Tester Range | 5 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
The waveform varies depending on the injector injection.
WAVEFORM 2
| ECM Terminal Name | Between PCV+ and PCV- |
| Tester Range | 10 V/DIV., 5 msec./DIV. |
| Condition | Idling or cranking with warm engine |
The waveform varies depending on the suction control valve operation.
WAVEFORM 3
| ECM Terminal Name | Between INJF and E1 Between INF2 and E1 |
| Tester Range | 2 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
The waveform varies depending on the injector injection.