Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0135612 ANTI-LOCK BRAKE SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TEST MODE PROCEDURE  


TEST MODE PROCEDURE (SIGNAL CHECK)


HINT:
·

After entering Test Mode, all Test Mode DTCs are stored. Then, during the signal check, the Test Mode DTCs for items which the brake actuator assembly (skid control ECU) determines to be normal are cleared.

·

Once the vehicle returns to normal mode, all Test Mode DTCs are cleared.



a.

When using the GTS:

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is in the straight-ahead position.


iii.

Check that the shift lever is in neutral and apply the parking brake.


iv.

Connect the GTS to the DLC3.


v.

Turn the ignition switch to ON.


vi.

Turn the GTS on.


vii.

Switch the brake actuator assembly (skid control ECU) to Test Mode using the GTS.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3

viii.

Check that the ABS warning light blinks in the Test Mode pattern (0.125 seconds on and 0.125 seconds off).



b.

When using SST check wire:

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is in the straight-ahead position.


iii.

Check that the shift lever is in neutral and apply the parking brake.


iv.
C311984C01
1.583,0.896 1.583,0.333 1.583,0.333 1.75,0.333 true 1.573,1.458 1.583,1.917 1.583,1.917 1.417,1.917 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 1.781,0.24 2.094,0.438 0.313,0.198 10 false CG 1.219,1.844 1.531,2.042 0.313,0.198 10 false TS
*a Front view of DLC3


Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:

Do not connect the incorrect terminals as this will cause damage.



v.

Turn the ignition switch to ON.


vi.

Check that the ABS warning light blinks in the Test Mode pattern (0.125 seconds on and 0.125 seconds off).




ABS SIGNAL CHECK


a.

Perform the deceleration sensor check.

i.

Enter Test Mode.

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3

ii.

Keep the vehicle stationary on a level surface for 1 second or more.



b.

Perform the 2WD to 4WD and L4 shift operation check.

i.

Enter Test Mode.

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3

ii.

Start the engine.


iii.

Set the vehicle to the 2WD state.


iv.

Set the vehicle to the 4WD state.


v.

Set the vehicle to the L4 state.



c.

Speed Sensor Check

NOTICE:
·

The speed sensor check may not be completed if the speed sensor check is started while turning the steering wheel or spinning the wheels.

·

After the ABS warning light goes off, if the vehicle speed exceeds 80 km/h (50 mph), a sensor check code is stored again. Decelerate or stop the vehicle before the vehicle speed reaches 80 km/h (50 mph).

·

If the sensor check is not completed, the ABS warning light blinks while driving and the ABS does not operate.



i.

Enter Test Mode.

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3

ii.

Start the engine.


iii.

Drive the vehicle straight-ahead. Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds.


iv.

Check that the ABS warning light goes off.

HINT:
·

The sensor check may not be completed if wheelspin occurs.

·

The ABS warning light comes on immediately if a malfunction is detected during the speed sensor check.




v.

Stop the vehicle.

HINT:

When the sensor check is completed, the ABS warning light goes off while driving and blinks in the Test Mode pattern (0.125 seconds on and 0.125 seconds off) while the vehicle is stationary.





END OF SIGNAL CHECK


a.

If the signal check is completed, the ABS warning light blinks (0.125 seconds on and 0.125 seconds off) when the vehicle stops and the ABS warning light is off while the vehicle is being driven.

NOTICE:

If the signal check has not been completed, the ABS warning light blinks while driving and the ABS does not operate.




READ DTC OF SIGNAL CHECK FUNCTION


a.

When using the GTS:

i.

Read the output DTC(s) by following the GTS screen.

NOTICE:
·

If only DTCs other than Test Mode (signal check) DTCs are output, repair the malfunctions and clear the DTCs.

·

If Test Mode (signal check) DTCs and other DTCs are output or if only Test Mode (signal check) DTCs are output, repair the malfunctions, clear the DTCs and Test Mode (signal check) DTCs, and perform the Test Mode (signal check) inspection again.



HINT:

Refer to the List of Test Mode (Signal Check) DTC.



ii.

Turn the ignition switch off and disconnect the GTS.



b.

When using SST check wire:

NOTICE:

When terminals 12 (TS) and 4 (CG) are not connected, do not turn the ignition switch off. If the ignition switch is turned off and then to ON again with no connection between terminals 12 (TS) and 4 (CG), the Test Mode DTCs are cleared.


i.
C311984C02
1.583,0.896 1.583,0.333 1.583,0.333 1.75,0.333 true 1.573,1.458 1.5,1.917 1.5,1.917 1.417,1.917 true 1.76,1.448 1.917,1.917 1.917,1.917 2,1.917 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 1.781,0.24 2.094,0.438 0.313,0.198 10 false CG 2.083,1.833 2.396,2.031 0.313,0.198 10 false TC 1.219,1.844 1.531,2.042 0.313,0.198 10 false TS
*a Front view of DLC3


Using SST, connect terminals 12 (TS), 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:

Do not connect the incorrect terminals as this will cause damage.



ii.

Count the number of blinks of the ABS warning light.

NOTICE:
·

If only DTCs other than Test Mode sensor check DTCs are output, repair the malfunctions and clear the DTCs.

·

If Test Mode (signal check) DTCs and other DTCs are output or if only Test Mode (signal check) DTCs are output, repair the malfunctions, clear the DTCs and Test Mode (signal check) DTCs, and perform the Test Mode (signal check) inspection again.



HINT:
·

If more than 1 malfunction is detected at the same time, the lowest numbered code is output first.

·

Refer to the List of Test Mode (Signal Check) DTC.




iii.

Disconnect SST from terminals 12 (TS), 13 (TC) and 4 (CG) of the DLC3 and turn the ignition switch off.


iv.

Turn the ignition switch to ON.

HINT:

The Test Mode DTCs are cleared by turning the ignition switch to ON again.


Test Mode (Signal Check) DTC Memory Status Chart
DLC3 Ignition switch ON Ignition switch off Ignition switch off → Ignition switch ON
Terminals 12 (TS) and 4 (CG) connected DTC memory maintained DTC memory maintained DTC memory maintained
Terminals 12 (TS) and 4 (CG) not connected DTC memory maintained DTC memory maintained DTC memory cleared




LIST OF TEST MODE (SIGNAL CHECK) DTC


HINT:

The codes in this table are output only in Test Mode (signal check).


ABS Sensor
DTC No. Detection Item Trouble Area
GTS Display ABS Warning Light Display
C1271 71 Low output signal of front speed sensor RH
·

Front speed sensor RH

·

Sensor installation

·

Front axle hub sub-assembly RH (Front speed sensor rotor RH)


C1272 72 Low output signal of front speed sensor LH
·

Front speed sensor LH

·

Sensor installation

·

Front axle hub sub-assembly LH (Front speed sensor rotor LH)


C1273 73 Low output signal of rear speed sensor RH
·

Rear speed sensor RH

·

Sensor installation

·

Rear axle hub and bearing assembly RH (Rear speed sensor rotor RH)


C1274 74 Low output signal of rear speed sensor LH
·

Rear speed sensor LH

·

Sensor installation

·

Rear axle hub and bearing assembly LH (Rear speed sensor rotor LH)


C1275 75 Abnormal change in output signal of front speed sensor RH Front axle hub sub-assembly RH (Front speed sensor rotor RH)
C1276 76 Abnormal change in output signal of front speed sensor LH Front axle hub sub-assembly LH (Front speed sensor rotor LH)
C1277 77 Abnormal change in output signal of rear speed sensor RH Rear axle hub and bearing assembly RH (Rear speed sensor rotor RH)
C1278 78 Abnormal change in output signal of rear speed sensor LH Rear axle hub and bearing assembly RH (Rear speed sensor rotor RH)
C1279 79 Deceleration sensor output voltage malfunction
·

Deceleration sensor

·

Sensor installation


C1282 82 Center differential lock position switch malfunction (4WD position switch malfunction)
·

Transfer system

·

No. 1 transfer indicator switch (4WD position switch)

·

EXI terminal circuit

·

Brake actuator assembly (Skid control ECU)


C1283 83 L4 position switch malfunction
·

No. 1 transfer indicator switch (L4 position switch)

·

EXI2 terminal circuit

·

Brake actuator assembly (Skid control ECU)