Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0135612 ANTI-LOCK BRAKE SYSTEM U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TERMINALS OF ECU  


TERMINAL OF ECU


C160258C20
0.343,0.207 0.536,0.409 0.193,0.202 10 *a
*a Component without harness connected
(Brake Actuator Assembly [Skid Control ECU])
- -


Terminal No. (Symbol) Terminal Description
1 (GND1) Ground
3 (GL1) Deceleration sensor signal input
4 (RL-) Rear LH wheel speed (-) signal input
5 (RL+) Rear LH wheel speed (+) signal input
6 (FR-) Front RH wheel speed (-) signal input
7 (FR+) Front RH wheel speed (+) signal input
8 (EXI2) No. 1 transfer indicator switch (L4 position switch) input
9 (EXI3)* No. 4 transfer indicator switch (Rear differential lock position switch) signal input
12 (+BS) ABS solenoid power supply
13 (GND2) Ground
14 (CANL) CAN communication line L
15 (GGND) Deceleration sensor ground
16 (RR-) Rear RH wheel speed (-) signal input
17 (RR+) Rear RH wheel speed (+) signal input
18 (FL-) Front LH wheel speed (-) signal input
19 (FL+) Front LH wheel speed (+) signal input
21 (WA) ABS warning light output
22 (SP1) Speed signal output for speedometer
24 (+BM) ABS motor relay power supply
25 (CANH) CAN communication line H
26 (VGS) Deceleration sensor power supply
28 (STP) Stop light switch input
30 (TC) Diagnosis code check input
31 (EXI) No. 1 transfer indicator switch (4WD position switch) input
32 (TS) Signal check input
34 (IG1) Brake actuator assembly (skid control ECU) power supply

*: w/ Rear Differential Lock


TERMINAL INSPECTION


C160261C12
1.823,1.51 2.198,1.76 0.375,0.25 0.344,0.229 0.51,0.406 0.167,0.177 10 false *a 1.896,1.563 2.292,1.729 0.396,0.167 10 false A20
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])
- -


HINT:

Voltage cannot be measured with the connectors connected to the brake actuator assembly (skid control ECU) as the connectors are watertight.


a.

Disconnect the A20 brake actuator assembly (skid control ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
A20-1 (GND1) - Body ground W-B Ground Always Below 1 Ω
A20-8 (EXI2) - Body ground B-Y No. 1 transfer indicator switch (L4 position switch) input Transfer position L4 Below 1 Ω
A20-9 (EXI3)* - Body ground R-L No. 4 transfer indicator switch (Rear differential lock position switch) signal input
·

Ignition switch ON

·

Rear differential free


11 to 14 V
A20-12 (+BS) - Body ground R ABS solenoid power supply Always 11 to 14 V
A20-13 (GND2) - Body ground W-B Ground Always Below 1 Ω
A20-24 (+BM) - Body ground W ABS motor relay power supply Always 11 to 14 V
A20-28 (STP) - Body ground W Stop light switch input Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V
A20-31 (EXI) - Body ground R-Y No. 1 transfer indicator switch (4WD position switch) input
·

Ignition switch ON

·

Transfer position 2WD


11 to 14 V
A20-34 (IG1) - Body ground B-Y Brake actuator assembly (skid control ECU) power supply Ignition switch ON 11 to 14 V

*: w/ Rear Differential Lock

If the result is not as specified, there may be a malfunction on the wire harness side.