Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0135612 ANTI-LOCK BRAKE SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  DTC CHECK / CLEAR  


DTC CHECK/CLEAR (When Using GTS)


a.

Check for DTCs.

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105

vi.

Check the details of the DTCs.



b.

Clear the DTCs.

NOTICE:

Clearing the DTC also clears the freeze frame data.


i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Turn the ignition switch to ON.


iv.

Turn the GTS on.


v.

Enter the following menus: Chassis / ABS/VSC/TRC / Trouble Codes.

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

vi.

Clear the DTCs by following the prompts on the GTS.




DTC CHECK/CLEAR (When Using SST Check Wire)


a.
C311984C03
1.583,0.896 1.583,0.333 1.583,0.333 1.75,0.333 true 1.76,1.448 1.917,1.917 1.917,1.917 2,1.917 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 1.781,0.24 2.094,0.438 0.313,0.198 10 false CG 2.083,1.833 2.396,2.031 0.313,0.198 10 false TC
*a Front view of DLC3


Check for DTCs.

i.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:

Do not connect the incorrect terminals as this will cause damage.



ii.

Turn the ignition switch to ON.


iii.

Read the DTCs output from the ABS warning light in the combination meter.

HINT:
·

When the system is normal, the ABS warning light blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).

·

When only 1 DTC is output, the light outputs the same code after an interval of 4 seconds. Example: when DTC 21 is output, the light blinks twice, turns off for 1.5 seconds, blinks once, turns off for 4 seconds, and then repeats this output pattern.

·

When 2 or more DTCs are output, the light outputs the codes with an interval of 2.5 seconds between each different code, and it repeats the output of all codes after an interval of 4 seconds.




iv.

Check the details of the DTCs.

ABS DTC
Warning Light Display GTS Display
11 C146E
12 C146F
13 C146C
14 C146D
21 C1468
22 C1469
23 C146A
31 C1401
C1405
32 C1402
C1406
33 C1403
C1407
34 C1404
C1408
35 C1413
36 C1414
37 C1337
38 C1415
39 C1416
41 C1241
C1417
43 C1243
44 C1418
45 C1245
49 C1425
51 C1427
C1428


v.

Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.



b.
C311984C03
1.583,0.896 1.583,0.333 1.583,0.333 1.75,0.333 true 1.76,1.448 1.917,1.917 1.917,1.917 2,1.917 true 0.094,0.094 0.406,0.292 0.313,0.198 10 false *a 1.781,0.24 2.094,0.438 0.313,0.198 10 false CG 2.083,1.833 2.396,2.031 0.313,0.198 10 false TC
*a Front view of DLC3


Clear the DTCs.

i.

Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:

Do not connect the incorrect terminals as this will cause damage.



ii.

Turn the ignition switch to ON.


iii.

Clear the DTCs stored in the ECU by depressing the brake pedal 8 times or more within 5 seconds.


iv.

Check that the ABS warning light blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off).


v.

Remove SST from the terminals of the DLC3.




END OF DTC CHECK/CLEAR


a.

Turn the ignition switch to ON.


b.

Check that the ABS warning light goes off within approximately 3 seconds after turning the ignition switch to ON.