READ DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| ABS Warning Light | ABS warning light signal | ON or OFF | ON: Warning light on OFF: Warning light off |
- |
| Stop Light SW | Stop light switch assembly signal | ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released |
- |
| Deceleration Sensor | Deceleration sensor reading | Min.: -18.525 m/s2 Max.: 18.387 m/s2 |
- | Changes continuously during acceleration/deceleration. |
| Forward and Rearward G | Deceleration sensor reading | Min.: -25.10 m/s2 Max.: 24.90 m/s2 |
- | Changes in proportion with acceleration during acceleration/deceleration. |
| Rear Diff Lock Switch | Rear differential lock position switch signal | ON or OFF | w/ Rear Differential Lock: ON: Rear differential lock position switch on OFF: Rear differential lock position switch off w/o Rear Differential Lock: OFF |
- |
| L4 Switch | L4 position switch signal | ON or OFF | ON: L4 OFF: except L4 |
- |
| FR Wheel Speed | Front speed sensor RH reading | Min.: 0 km/h (0 mph) Max.: 326 km/h (202 mph) |
Actual wheel speed | No large fluctuations when driving at a constant speed. |
| FL Wheel Speed | Front speed sensor LH reading | Min.: 0 km/h (0 mph) Max.: 326 km/h (202 mph) |
Actual wheel speed | No large fluctuations when driving at a constant speed. |
| RR Wheel Speed | Rear speed sensor RH reading | Min.: 0 km/h (0 mph) Max.: 326 km/h (202 mph) |
Actual wheel speed | No large fluctuations when driving at a constant speed. |
| RL Wheel Speed | Rear speed sensor LH reading | Min.: 0 km/h (0 mph) Max.: 326 km/h (202 mph) |
Actual wheel speed | No large fluctuations when driving at a constant speed. |
| Vehicle Speed | Maximum wheel speed sensor reading | Min.: 0 km/h (0 mph) Max.: 326 km/h (202 mph) |
Actual wheel speed | No large fluctuations when driving at a constant speed. |
| FR Wheel Acceleration | Front wheel RH acceleration | Min.: -200.84 m/s2 Max.: 199.27 m/s2 |
- | Changes continuously during acceleration/deceleration. |
| FL Wheel Acceleration | Front wheel LH acceleration | Min.: -200.84 m/s2 Max.: 199.27 m/s2 |
- | Changes continuously during acceleration/deceleration. |
| RR Wheel Acceleration | Rear wheel RH acceleration | Min.: -200.84 m/s2 Max.: 199.27 m/s2 |
- | Changes continuously during acceleration/deceleration. |
| RL Wheel Acceleration | Rear wheel LH acceleration | Min.: -200.84 m/s2 Max.: 199.27 m/s2 |
- | Changes continuously during acceleration/deceleration. |
| FR Wheel ABS Ctrl Status | Front wheel RH ABS control status | ON or OFF | ON: During control OFF: Not during control |
- |
| FL Wheel ABS Ctrl Status | Front wheel LH ABS control status | ON or OFF | ON: During control OFF: Not during control |
- |
| RR Wheel ABS Ctrl Status | Rear wheel RH ABS control status | ON or OFF | ON: During control OFF: Not during control |
- |
| RL Wheel ABS Ctrl Status | Rear wheel LH ABS control status | ON or OFF | ON: During control OFF: Not during control |
- |
| Solenoid Relay | ABS solenoid relay | ON or OFF | ON: ABS solenoid relay on OFF: ABS solenoid relay off |
- |
| ECB Motor Relay | ABS motor relay | ON or OFF | ON: ABS motor relay on OFF: ABS motor relay off |
|
| ABS Solenoid (SFRH) | Front wheel RH hold solenoid | ON or OFF | ON: Operates OFF: Does not operate |
- |
| ABS Solenoid (SFRR) | Front wheel RH release solenoid | ON or OFF | ON: Operates OFF: Does not operate |
- |
| ABS Solenoid (SFLH) | Front wheel LH hold solenoid | ON or OFF | ON: Operates OFF: Does not operate |
- |
| ABS Solenoid (SFLR) | Front wheel LH release solenoid | ON or OFF | ON: Operates OFF: Does not operate |
- |
| ABS Solenoid (SRRH) | Rear wheel hold solenoid | ON or OFF | ON: Operates OFF: Does not operate |
- |
| ABS Solenoid (SRRR) | Rear wheel release solenoid | ON or OFF | ON: Operates OFF: Does not operate |
- |
| FR Speed Open | Front speed sensor RH open detection | Error or Normal | Normal | - |
| FL Speed Open | Front speed sensor LH open detection | Error or Normal | Normal | - |
| RR Speed Open | Rear speed sensor RH open detection | Error or Normal | Normal | - |
| RL Speed Open | Rear speed sensor LH open detection | Error or Normal | Normal | - |
| Deceleration Open | Acceleration sensor open detection | Error or Normal | Normal | - |
| IG1 Voltage Value | IG1 voltage value | Min.: 0.00 V Max.: 20.00 V |
- | - |
| MT Voltage Value | Motor driving monitor voltage | Min.: 0.00 V Max.: 20.00 V |
- | - |
| Number of DTC | Number of DTCs stored | Min.: 0 Max.: 255 |
0 | - |
| IG Voltage Value Decreased | IG voltage value decrease detection | Error or Normal | Normal | - |
| IG Voltage Value Increased | IG voltage value increase detection | Error or Normal | Normal | - |
| FR Speed Sensor Voltage Open | Front speed sensor RH voltage open detection | Error or Normal | Normal | - |
| FL Speed Sensor Voltage Open | Front speed sensor LH voltage open detection | Error or Normal | Normal | - |
| RR Speed Sensor Voltage Open | Rear speed sensor RH voltage open detection | Error or Normal | Normal | - |
| RL Speed Sensor Voltage Open | Rear speed sensor LH voltage open detection | Error or Normal | Normal | - |
| 4WD LOCK Switch | 4WD position switch signal | ON or OFF | ON: 4WD OFF: 2WD |
- |
PERFORM ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
According to the display on the GTS, perform the Active Test.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| ABS Warning Light | ABS warning light | Warning light ON / OFF | Observe the combination meter. |
| Solenoid Relay | ABS solenoid relay | Relay ON / OFF | Check for DTCs after performing this Active Test. If no codes are output, the solenoid relay is operating normally. |
| Motor Relay | ABS motor relay | Relay ON / OFF | The operating sound of the motor can be heard. |
| ABS Solenoid (SRRR) | Rear wheel release solenoid | Solenoid ON / OFF | The operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SRRH) | Rear wheel hold solenoid | Solenoid ON / OFF | The operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SFLR) | Front wheel LH release solenoid | Solenoid ON / OFF | The operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SFLH) | Front wheel LH hold solenoid | Solenoid ON / OFF | The operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SFRR) | Front wheel RH release solenoid | Solenoid ON / OFF | The operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid (SFRH) | Front wheel RH hold solenoid | Solenoid ON / OFF | The operating sound of the solenoid (clicking sound) can be heard. |
| ABS Solenoid | Holding solenoids (SFRH, SFLH and SRRH) and release solenoids (SFRR, SFLR and SRRR) | Start/Stop | Start: When Start is selected, the selected solenoids turn ON. Stop: When Stop is selected, the selected solenoids turn OFF.
|