Home › Engine / Hybrid System › 1HZ (ENGINE CONTROL) › MANIFOLD ABSOLUTE PRESSURE SENSOR(w/ EGR System)
RM25T0E _51 Engine / Hybrid System _029759 1HZ ENGINE CONTROL _0135872 MANIFOLD ABSOLUTE PRESSURE SENSOR(w/ EGR System) G

1HZ ENGINE CONTROL  MANIFOLD ABSOLUTE PRESSURE SENSOR(w/ EGR System)  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 89421D 1.CHECK DIESEL TURBO PRESSURE SENSOR

a.
A162709C02
1.198,1.323 0.646,1.323 true 2.01,1.323 2.563,1.323 true 0.104,0.042 0.271,0.198 0.167,0.156 10 *a 0.385,1.229 0.604,1.385 0.219,0.156 10 E2 2.604,1.229 2.823,1.385 0.219,0.156 10 VC
*a Front view of wire harness connector
(to Diesel Turbo Pressure Sensor)


Inspect the power source voltage.

i.

Disconnect the diesel turbo pressure sensor connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
3 (VC) - 1 (E2) Ignition Switch ON 4.75 to 5.25 V



iii.

Turn the ignition switch off.


iv.

Reconnect the diesel turbo pressure sensor connector.



b.
A190329C11
1.313,1.208 1.656,1.417 0.344,0.208 2.146,1.385 2.021,1.385 2.021,1.385 1.656,1.875 true 1.708,1.979 2.26,2.708 2.26,2.708 2.417,2.708 true 0.073,0.073 0.344,0.313 0.271,0.24 10 false *a 1.396,1.229 1.625,1.406 0.229,0.177 10 false E9 2.219,1.281 2.74,1.49 0.521,0.208 10 false 4 (PIM) 2.49,2.625 3.01,2.854 0.521,0.229 10 false 16 (E2)
*a Component with harness connected
(Emission Control ECU)


Check the power supply.

i.

Turn the ignition switch to ON.


ii.

Disconnect the vacuum hose from the diesel turbo pressure sensor.


iii.
A329079N01
2.479,3.073 2.781,2.604 2.781,2.604 2.958,2.604 true 2.656,1.219 2.833,0.781 2.833,0.781 2.948,0.781 true 3.031,2.542 3.385,2.719 0.354,0.177 10 false SST 3.01,0.708 3.365,0.885 0.354,0.177 10 false SST

Using SST, apply pressure to the diesel turbo pressure sensor.

SST
09992-00242  


iv.

Using a vacuum pump, apply vacuum to the diesel turbo pressure sensor.


v.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E9-4 (PIM) - E9-16 (E2) 78.5 kPa (0.80 kgf/cm2, 11.4 psi) 2.0 to 2.3 V
Same as atmospheric pressure 0.8 to 1.4 V
40 kPa (300 mmHg, 11.8 in.Hg) 1.0 to 1.2 V


If the result is not as specified, replace the diesel turbo pressure sensor.