Home › Engine / Hybrid System › 1VD-FTV (INTAKE / EXHAUST) › EXHAUST PIPE (for 5 Door) › 2014.08–2016.08
RM25T0E _51 Engine / Hybrid System _029894 1VD-FTV INTAKE / EXHAUST _0136511 EXHAUST PIPE(for 5 Door) A

1VD-FTV INTAKE / EXHAUST  EXHAUST PIPE(for 5 Door)  INSTALLATION  


PROCEDURE

Hide 18431 1.INSTALL UPPER CATALYTIC CONVERTER INSULATOR

a.

Install the upper catalytic converter insulator with the 2 bolts and nut.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 18450A 2.INSTALL MONOLITHIC CONVERTER ASSEMBLY

a.

Temporarily install a new gasket to the monolithic converter assembly by hand.

HINT:

Be sure to install the gasket evenly and as much as possible.



b.
A104635C26
2.625,1.063 2.958,1.063 true 1.49,1.792 1.656,1.792 1.656,1.792 2.115,1.448 false 3.01,0.948 3.219,1.156 0.208,0.208 10 false *a 1.271,1.688 1.49,1.865 0.219,0.177 10 false *1
*1 Gasket
*a Wooden Block


Using a plastic-faced hammer and wooden block, tap the gasket onto the monolithic converter assembly so that the gasket is flush with the pipe end.

NOTICE:
·

Install the gasket in the correct direction.

·

Do not damage the outer surface of the gasket.

·

Do not reuse the gasket.

·

Do not push in the gasket with the exhaust pipe when connecting it.




c.
A162138

Install a new gasket onto the outlet turbine elbow.


d.
A166035

Loosely install the monolithic converter assembly with 3 new nuts.

HINT:

Tighten the nuts until the contact surface of the monolithic converter assembly contacts with the outlet turbine elbow.



e.

Loosely install the center converter protector stay with the 3 bolts.

HINT:

Tighten the bolts so that the position of the monolithic converter assembly can be adjusted in a later step.



f.

Tighten the monolithic converter's nuts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


g.

Tighten the converter protector stay's bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17410 3.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A104634

Inspect the compression spring.

i.

Using a vernier caliper, measure the free length of the compression spring.

Standard free length:

43 mm (1.69 in.)


If the free length is not as specified, replace the compression spring.



b.

Install the exhaust pipe support cushion to the front exhaust pipe assembly with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


c.

Temporarily install the front exhaust pipe assembly with the 2 bolts and 2 compression springs labeled A, and the 2 nuts labeled B.

A162134N01
1.573,2.604 1.74,2.771 0.167,0.167 10 true A 2.031,2.375 2.198,2.542 0.167,0.167 10 true A 5.302,2.281 5.448,2.458 0.146,0.177 10 true B 5.521,2.177 5.677,2.365 0.156,0.188 10 true B


d.

Tighten the bolts labeled A.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:
·
A162131C02
0.958,2.052 1.188,2.25 0.229,0.198 10 false *a 2.125,2.073 2.354,2.271 0.229,0.198 10 false *b
*a CORRECT
*b INCORRECT



·

When tightening the bolts, make sure the lengths of the springs are approximately the same.

·

Make sure the joint part is movable.

·

Make sure the bolts do not get caught on the flange.




e.

Tighten the nuts labeled B.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17430 4.INSTALL TAILPIPE ASSEMBLY

a.
A328277

Install a new gasket onto the front exhaust pipe assembly.


b.

Install the 2 exhaust pipe support cushions to the tailpipe assembly with the 4 nuts.


c.

Temporarily install the tailpipe assembly with 2 new bolts and 2 new nuts labeled A, and the 4 nuts labeled B

A162133N01
1.125,2.469 1.271,2.656 0.146,0.188 10 true A 1.771,1.75 1.938,1.948 0.167,0.198 10 true A 3.51,2.198 3.677,2.406 0.167,0.208 10 true B 3.802,2.281 3.958,2.479 0.156,0.198 10 true B 5.646,2.229 5.802,2.427 0.156,0.198 10 false B 5.958,2.156 6.125,2.344 0.167,0.188 10 true B


d.

Tighten the nuts labeled B

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


e.

Tighten the bolts and nuts labeled A.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)