1.CLEAN CYLINDER HEAD
Using a gasket scraper, remove all the gasket material from the cylinder block sub-assembly contact surface.
Be careful not to scratch the cylinder block sub-assembly contact surface.
Using a wire brush, remove all the carbon from the combustion chambers.
Be careful not to scratch the combustion chambers.
Using a valve guide bushing brush and solvent, clean all the valve guide bushes.
Using a soft brush and solvent, thoroughly clean the cylinder head.
2.INSPECT CYLINDER HEAD
Using a precision straightedge and feeler gauge, measure the warpage of the contact surfaces of the cylinder block and manifolds.
| *a | Cylinder Block Side | *b | Intake Manifold Side |
| *c | Exhaust Manifold Side | - | - |
| Item | Specified Condition |
|---|---|
| Cylinder block side | 0.05 mm (0.00197 in.) |
| Intake manifold side | 0.08 mm (0.00315 in.) |
| Exhaust manifold side | 0.05 mm (0.00197 in.) |
| Item | Specified Condition |
|---|---|
| Cylinder block side | 0.10 mm (0.00394 in.) |
| Intake manifold side | |
| Exhaust manifold side |
If the warpage is more than the maximum, replace the cylinder head.
Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.
If there are cracks, replace the cylinder head.
13711B 3.INSPECT INNER COMPRESSION SPRING
Using a vernier caliper, measure the free length of the inner compression spring.
47.8 mm (1.88 in.)
If the free length is not as specified, replace the inner compression spring.
Using a steel square, measure the deviation of the inner compression spring.
2.0 mm (0.0787 in.)
If the deviation is more than the maximum, replace the inner compression spring.
Using a spring tester, measure the tension of the inner compression spring at the standard installed length.
186 to 206 N (19 to 21 kgf, 41.8 to 46.3 lbf) at 36.2 mm (1.43 in.)
If the tension is not as specified, replace the inner compression spring.
4.CLEAN VALVE
Using a gasket scraper, chip off any carbon from the valve head.
Using a wire brush, thoroughly clean the valve.
5.INSPECT VALVE
Using a micrometer, measure the diameter of the valve stem.
| Item | Specified Condition |
|---|---|
| Intake valve | 5.470 to 5.485 mm (0.2154 to 0.2159 in.) |
| Exhaust valve | 5.465 to 5.480 mm (0.2152 to 0.2157 in.) |
Inspect the valve face angle.
Grind the valve enough to remove pits and carbon.
Check that the valve is ground to the correct valve face angle.
44.5°
Using a vernier caliper, measure the valve head margin thickness.
1.0 mm (0.0394 in.)
0.5 mm (0.0197 in.)
If the margin thickness is less than the minimum, replace the valve.
Using a vernier caliper, measure the overall length of the valve.
| Item | Specified Condition |
|---|---|
| Intake valve | 106.95 mm (4.21 in.) |
| Exhaust valve | 105.80 mm (4.17 in.) |
| Item | Specified Condition |
|---|---|
| Intake valve | 106.40 mm (4.19 in.) |
| Exhaust valve | 105.30 mm (4.15 in.) |
If the overall length is less than the minimum, replace the valve.
Check the surface of the valve stem tip for wear.
Do not grind the valve so it becomes shorter than the minimum overall length.
If the valve stem tip is worn, resurface the tip with a grinder or replace the valve.
6.INSPECT VALVE GUIDE BUSH OIL CLEARANCE
Using a caliper gauge, measure the inside diameter of the guide bush.
5.51 to 5.53 mm (0.217 to 0.218 in.)
Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.
| Item | Specified Condition |
|---|---|
| Intake side | 0.025 to 0.060 mm (0.000984 to 0.00236 in.) |
| Exhaust side | 0.030 to 0.065 mm (0.00118 to 0.00256 in.) |
| Item | Specified Condition |
|---|---|
| Intake side | 0.08 mm (0.00315 in.) |
| Exhaust side | 0.10 mm (0.00394 in.) |
If the oil clearance is more than the maximum, replace the valve and valve guide bush.
7.CLEAN VALVE SEAT
Using a 45° carbide cutter, resurface the valve seats.
Clean the valve seats.
8.INSPECT VALVE SEAT
Apply a light coat of Prussian blue to the valve face.
Lightly press the valve face against the valve seat.
Do not rotate the valve.
Check the valve face and valve seat by using the following procedure.
Check that Prussian blue appears around the entire valve face. If not, replace the valve.
If Prussian blue appears around the entire valve seat, the guide and valve face are concentric. If not, resurface the valve seat.
Check that the seat contacts the middle of the valve face with the width below.
1.0 to 1.4 mm (0.0394 to 0.0551 in.)
9.INSPECT CAMSHAFT OIL CLEARANCE
10.INSPECT CAMSHAFT THRUST CLEARANCE
13751 11.INSPECT VALVE LIFTER
Using a micrometer, measure the valve lifter diameter.
30.966 to 30.976 mm (1.219 to 1.220 in.)
If the result is not as specified, replace the valve lifter.
Using a caliper gauge, measure the lifter bore diameter of the cylinder head.
31.009 to 31.025 mm (1.220 to 1.221 in.)
Subtract the valve lifter diameter from the lifter bore diameter of the cylinder head.
0.033 to 0.059 mm (0.00130 to 0.00232 in.)
0.08 mm (0.00315 in.)
If the oil clearance is more than the maximum, replace the valve lifter.
If necessary, replace the cylinder head.