Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › CYLINDER BLOCK
RM25T0E _51 Engine / Hybrid System _029891 1GR-FE ENGINE MECHANICAL _0136562 CYLINDER BLOCK A

1GR-FE ENGINE MECHANICAL  CYLINDER BLOCK  REPLACEMENT  


PROCEDURE

Hide 1.REPLACE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Using an E5, E7 and E8 "TORX" wrench, remove the stud bolts.


b.

Using an E5, E7 and E8 "TORX" wrench, install new stud bolts.

A223066C01
0.573,0.104 1.323,0.25 0.75,0.146 10 false *a 4.083,0.104 4.396,0.365 0.313,0.26 10 false *b 0.573,2.552 0.927,2.771 0.354,0.219 10 false *c 4.104,2.552 4.427,2.781 0.323,0.229 10 false *d 0.427,1.823 0.563,1.99 0.135,0.167 10 true A 0.427,4.083 0.563,4.25 0.135,0.167 10 false B 1.781,4.083 1.917,4.25 0.135,0.167 10 true B 2.271,1.708 2.406,1.875 0.135,0.167 10 true A 3,1.229 3.563,1.573 0.563,0.344 10 false *f 2.969,3.708 3.573,4.083 0.604,0.375 10 false *h 6.292,1.302 6.958,1.646 0.667,0.344 10 false *g 6.333,3.719 7,4.063 0.667,0.344 10 false *i 5.917,3.24 6.052,3.406 0.135,0.167 10 false D 4.104,3.542 4.24,3.708 0.135,0.167 10 true D 3.958,1.854 4.094,2.021 0.135,0.167 10 true C 5.625,1.844 5.76,2.01 0.135,0.167 10 true C
*a Front Side *b Rear Side
*c Lower Side *d Upper Side
*f 52 mm (2.05 in.) *g 23 mm (0.906 in.)
*h 55 mm (2.17 in.) *i 22.5 mm (0.886 in.)


Torque:
for stud bolt A and B : 11 N*m (112 kgf*cm, 8 ft.*lbf)
for stud bolt C and D : 4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 2.REPLACE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pin unless it is being replaced.


a.

Remove the straight pins.


b.

Using a plastic-faced hammer, tap new straight pins into the cylinder block.

A223067C01
0.552,0.51 1.271,0.667 0.719,0.156 10 false *a 0.51,2.719 1.229,2.875 0.719,0.156 10 false *b 0.51,5.125 1.292,5.281 0.781,0.156 10 false *c 4.042,5.125 4.833,5.281 0.792,0.156 10 false *d 4.063,2.719 4.781,2.875 0.719,0.156 10 false *b 4.073,0.51 4.792,0.667 0.719,0.156 10 false *a 3.125,2.073 3.375,2.323 0.25,0.25 10 false *g 3.125,4.354 3.323,4.583 0.198,0.229 10 false *g 3.094,6.302 3.375,6.531 0.281,0.229 10 false *f 3.073,6.01 3.302,6.198 0.229,0.188 10 false *i 6.531,6.031 6.854,6.219 0.323,0.188 10 false *h 6.531,4.083 6.802,4.25 0.271,0.167 10 false *h 6.521,1.813 6.781,2 0.26,0.188 10 false *h 6.5,6.313 6.719,6.583 0.219,0.271 10 false *e 6.51,4.385 6.781,4.667 0.271,0.281 10 false *e 6.5,2.094 6.844,2.354 0.344,0.26 10 false *e 3.104,3.99 3.24,4.208 0.135,0.219 10 false *j 3.094,1.563 3.677,1.875 0.583,0.313 10 false *k 1.115,1.344 1.271,1.5 0.156,0.156 10 true A 0.75,3.302 0.906,3.458 0.156,0.156 10 true B 2.385,4.313 2.542,4.469 0.156,0.156 10 false B 0.865,6.469 1.021,6.625 0.156,0.156 10 true C 1.115,6.24 1.271,6.396 0.156,0.156 10 true C 1.979,6.469 2.135,6.625 0.156,0.156 10 true C 2.188,6.229 2.344,6.385 0.156,0.156 10 true C 4.188,7.198 4.344,7.354 0.156,0.156 10 true D 5.417,5.5 5.573,5.656 0.156,0.156 10 true D 4.875,3.979 5.031,4.135 0.156,0.156 10 true D 4.052,1.875 4.208,2.031 0.156,0.156 10 true D 5.583,1.542 5.74,1.698 0.156,0.156 10 true D
*a Front Side *b Rear Side
*c Upper Side *d Lower Side
*e 4.0 mm (0.157 in.) *f 8.0 mm (0.315 in.)
*g 10 mm (0.394 in.) *h 12 mm (0.472 in.)
*i 18 mm (0.709 in.) *j 22 mm (0.866 in.)
*k 36 mm (1.42 in.) - -


Standard Protrusion Height:
Item Specified Condition
Pin A 22.5 to 23.5 mm (0.886 to 0.925 in.)
Pin B 10.5 to 11.5 mm (0.413 to 0.453 in.)
Pin C 8.5 to 9.5 mm (0.335 to 0.374 in.)
Pin D 5.5 to 6.5 mm (0.217 to 0.256 in.)



Hide 13516 3.REPLACE OIL JET

NOTICE:

It is not necessary to remove the oil jet unless it is being replaced.


a.

Using a screwdriver and hammer, tap out the oil jet.


b.
A326750C01
3.094,2 2.906,2 2.906,2 2.74,1.74 true 3.135,1.917 3.396,2.094 0.26,0.177 10 false *a
*a 21.5 to 31.5°


Using a screwdriver and hammer, tap in a new oil jet as shown in the illustration.