Home › Engine / Hybrid System › 1GR-FE (ENGINE MECHANICAL) › CYLINDER BLOCK
RM25T0E _51 Engine / Hybrid System _029891 1GR-FE ENGINE MECHANICAL _0136562 CYLINDER BLOCK A

1GR-FE ENGINE MECHANICAL  CYLINDER BLOCK  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT CONNECTING ROD THRUST CLEARANCE

a.
A326721

Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

Standard thrust clearance:

0.15 to 0.30 mm (0.00591 to 0.0118 in.)


Maximum thrust clearance:

0.35 mm (0.0138 in.)


If the thrust clearance is more than the maximum, inspect the connecting rod sub-assembly and crankshaft.


Hide 2.INSPECT CONNECTING ROD OIL CLEARANCE

a.

Uniformly loosen the 2 connecting rod bolts and remove the connecting rod cap together with the connecting rod bearing.


b.

Clean the crank pin and bearing.


c.

Check the crank pin and bearing for pitting and scratches. If the crank pin or bearing is damaged, replace the bearings. If necessary, replace the crankshaft.


d.
A326746C01
0.813,0.323 1.021,0.323 1.021,0.323 1.542,0.99 true 0.646,0.24 0.958,0.438 0.313,0.198 10 false *a
*a Plastigage


Lay a strip of Plastigage across the crank pin.

NOTICE:

Do not turn the crankshaft.



e.

Install the connecting rod bearing cap.

Click hereEngine / Hybrid System>1GR-FE (ENGINE MECHANICAL)>CYLINDER BLOCK>REASSEMBLY


f.

Uniformly loosen the 2 connecting rod bolts and remove the connecting rod cap together with the connecting rod bearing.


g.

Measure the Plastigage at its widest point.

A326749C01
4.052,0.833 4.396,0.833 true 5.448,0.708 5.792,0.708 true 1.094,0.333 1.313,0.333 1.313,0.333 1.656,0.833 true 0.906,0.26 1.219,0.417 0.313,0.156 10 false *a 3.875,0.781 4.188,0.938 0.313,0.156 10 false *b 5.271,0.646 5.583,0.802 0.313,0.156 10 false *b
*a Plastigage *b Number Mark


Standard oil clearance:

0.040 to 0.066 mm (0.00157 to 0.00260 in.)


Maximum oil clearance:

0.086 mm (0.00399 in.)


If the clearance is the maximum or more, select and replace the connecting rod bearing or replace the crankshaft.

HINT:

If replacing a bearing, replace it with one that has the same number marked on the connecting rod. There are 4 sizes of standard bearings, marked "1 ", "2", "3" and "4" accordingly.


Standard Bearing Center Wall Thickness:
Item Specified Condition
Mark 1 1.484 to 1.487 mm (0.05843 to 0.05854 in.)
Mark 2 1.487 to 1.490 mm (0.05854 to 0.05866 in.)
Mark 3 1.490 to 1.493 mm (0.05866 to 0.05878 in.)
Mark 4 1.493 to 1.496 mm (0.05878 to 0.05900 in.)



h.

Completely remove the Plastigage.


Hide 3.REMOVE PISTON WITH CONNECTING ROD

a.
A326722

Using a ridge reamer, remove all the carbon from the top of the cylinder.


b.

Push out the piston with connecting rod from the cylinder block sub-assembly.

HINT:

Arrange the removed parts so that they can be reinstalled in their original locations.



Hide 13041 4.REMOVE CONNECTING ROD BEARING

a.

Remove the connecting rod bearing from the connecting rod sub-assembly and connecting rod bearing cap.

HINT:

Arrange the removed parts so that they can be reinstalled in their original locations.



Hide 13011 5.REMOVE PISTON RING SET

HINT:

Arrange the removed parts so that they can be reinstalled in their original locations.


a.
A326723

Using a piston ring expander, remove the No. 1 compression ring and No. 2 compression ring.


b.

Remove the 2 oil rings (side rail) and oil ring (expander) by hand.


Hide 13101A 6.REMOVE PISTON PIN HOLE SNAP RING

a.
A326724

Using a screwdriver, pry out the 2 piston pin hole snap rings.


Hide 13101 7.REMOVE PISTON WITH PIN SUB-ASSEMBLY

a.

Gradually heat the piston to approximately 80°C (176°F).


b.
A270642

Using a plastic-faced hammer and brass bar, lightly tap out the piston pin and remove the connecting rod sub-assembly.

HINT:

Arrange the removed parts so that they can be reinstalled in their original locations.



Hide 8.INSPECT CRANKSHAFT THRUST CLEARANCE

a.
A326725

Using a dial indicator, measure the crankshaft thrust clearance while prying the crankshaft back and forth with a screwdriver.

Standard thrust clearance:

0.04 to 0.24 mm (0.00157 to 0.00945 in.)


Maximum thrust clearance:

0.30 mm (0.0118 in.)


If the thrust clearance is more than the maximum, replace the thrust washers as a set.

Standard thrust washer thickness:

1.93 to 1.98 mm (0.0760 to 0.0780 in.)


If necessary, replace the crankshaft.


Hide 9.REMOVE CRANKSHAFT BEARING CAP

a.
A326726N01
0.24,0.667 0.396,0.865 0.156,0.198 10 false 2 0.74,0.396 0.896,0.594 0.156,0.198 10 false 3 1.146,0.188 1.302,0.385 0.156,0.198 10 false 4 1.521,0 1.677,0.198 0.156,0.198 10 false 1 1.833,1.865 1.99,2.063 0.156,0.198 10 true 6 2.427,1.479 2.583,1.677 0.156,0.198 10 true 7 2.906,1.229 3.063,1.427 0.156,0.198 10 true 8 3.26,0.969 3.417,1.167 0.156,0.198 10 true 5

Uniformly loosen the 8 bolts in several steps in the sequence shown in the illustration and remove the 8 bolts and 8 seal washers.


b.
A326727N01
0.313,0.646 0.469,0.844 0.156,0.198 10 false 2 0.833,0.396 0.99,0.594 0.156,0.198 10 false 6 1.229,0.188 1.385,0.385 0.156,0.198 10 false 8 1.719,0.063 1.927,0.229 0.208,0.167 10 true 16 2.01,0 2.146,0.156 0.135,0.156 10 false 4 2.417,0.073 2.635,0.229 0.219,0.156 10 false 12 2.677,0.104 2.896,0.26 0.219,0.156 10 false 11 2.958,0.313 3.177,0.469 0.219,0.156 10 false 3 0.531,1.375 0.74,1.573 0.208,0.198 10 true 10 1.042,1.073 1.25,1.271 0.208,0.198 10 true 14 0.948,1.667 1.104,1.854 0.156,0.188 10 true 9 1.604,1.385 1.76,1.573 0.156,0.188 10 true 13 1.542,1.604 1.698,1.792 0.156,0.188 10 true 1 2.125,1.271 2.281,1.458 0.156,0.188 10 true 5 1.677,0.729 1.833,0.917 0.156,0.188 10 true 15 2.583,1.042 2.74,1.229 0.156,0.188 10 true 7

Uniformly loosen the 16 crankshaft bearing cap set bolts in several steps in the sequence shown in the illustration and remove the crankshaft bearing cap set bolts.


c.
A326728C01
1.677,1.448 1.677,2 1.677,2 1.896,2 true 1.927,1.938 2.24,2.135 0.313,0.198 10 true *a
*a Protective Tape


Using a screwdriver, pry out the crankshaft bearing caps. Remove the 4 crankshaft bearing caps and lower crankshaft bearings.

NOTICE:
·

Push up on the crankshaft bearing cap little by little, alternating between the right and left sides until the crankshaft bearing cap can be removed.

·

Be careful not to damage the joint surfaces of the cylinder block sub-assembly and crankshaft bearing cap.



HINT:

Tape the screwdriver tip before use.



Hide 13411 10.REMOVE CRANKSHAFT

a.

Remove the crankshaft.


Hide 11011 11.REMOVE CRANKSHAFT THRUST WASHER

a.

Remove the 2 upper crankshaft thrust washers and 2 lower upper crankshaft thrust washers.


Hide 11711 12.REMOVE CRANKSHAFT BEARING

a.

Remove the upper crankshaft bearing and lower upper crankshaft bearing.


Hide 15708 13.REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A326729

Using a 5 mm hexagon socket wrench, remove the 3 bolts and 3 No. 1 oil nozzle sub-assemblies.