Home › Drivetrain › CLUTCH › CLUTCH UNIT (for 1GR-FE)
RM25T0E _52 Drivetrain _029901 CLUTCH _0136573 CLUTCH UNIT(for 1GR-FE) G

CLUTCH  CLUTCH UNIT(for 1GR-FE)  INSPECTION  


PROCEDURE

Hide 31250 1.INSPECT CLUTCH DISC ASSEMBLY

NOTICE:

When replacing the clutch disc assembly, make sure to perform an inspection of the flywheel sub-assembly and clutch cover assembly.


a.
C173305

Using a vernier caliper, measure the rivet depth.

Minimum Rivet Depth:

0.3 mm (0.0119 in.)


If the depth is less than the minimum, replace the clutch disc assembly.


b.
C114037

Using a dial gauge, measure the clutch disc assembly runout.

Maximum Runout:

0.8 mm (0.0314 in.)


If the runout is more than the maximum, replace the clutch disc assembly.


Hide 31210 2.INSPECT CLUTCH COVER ASSEMBLY

a.
C173310C02
0.406,0.667 0.635,0.896 0.229,0.229 10 false *b 0.802,0.5 1.344,0.667 0.542,0.167 10 false *a
*a Width
*b Depth


Using a vernier caliper, measure the depth and width of the diaphragm spring wear.

Maximum width:

6.0 mm (0.236 in.)


Maximum depth:

0.5 mm (0.0197 in.)


If the depth or width is more than the maximum, replace the clutch cover assembly.


b.
A272260C01
1.833,0.479 2.938,0.479 true 1.833,1.698 2.938,1.698 true 2.958,0.385 3.156,0.552 0.198,0.167 10 false *a 2.958,1.615 3.156,1.781 0.198,0.167 10 false *b
*a Hair cracks, scratches or discoloration
*b Hair cracks, discoloration or excessive wear


Perform a visual inspection of the clutch cover assembly.

i.

Inspect for hair cracks or scratches extending from the center outwards, or discoloration.


ii.

Inspect for hair cracks in a circular pattern, discoloration or excessive wear.

If there is any damage, replace the clutch cover assembly.



Hide 13405 3.INSPECT FLYWHEEL SUB-ASSEMBLY

a.
C212167

Using a dial gauge, check the flywheel sub-assembly runout.

Maximum Runout:

0.1 mm (0.00393 in.)


If the runout is more than the maximum, replace the flywheel sub-assembly.


b.
A272261C01
2.198,0.458 2.969,0.458 true 1.917,1.573 2.854,1.573 true 3.01,0.365 3.208,0.531 0.198,0.167 10 false *a 2.865,1.479 3.063,1.646 0.198,0.167 10 false *b
*a Hair cracks, scratches or discoloration
*b Hair cracks, discoloration or excessive wear


Perform a visual inspection of the flywheel sub-assembly.

i.

Inspect for hair cracks or scratches extending from the center outwards, or discoloration.


ii.

Inspect for hair cracks in a circular pattern, discoloration or excessive wear.

If there is any damage, replace the flywheel sub-assembly.



Hide 31230 4.INSPECT CLUTCH RELEASE BEARING ASSEMBLY

a.
C313350

Turn the clutch release bearing assembly by hand while applying force in the axial direction.

HINT:

The bearing is permanently lubricated and requires no cleaning or lubrication.

Replace the clutch release bearing assembly as necessary.



Hide 33311W 5.INSPECT INPUT SHAFT BEARING

a.
C313349

Turn the input shaft bearing by hand while applying rotational force and check that the bearing rotates smoothly.

If the bearing sticks or a considerable amount of resistance is felt, replace the input shaft bearing.

HINT:

The bearing is permanently lubricated and requires no cleaning or lubrication.



Hide 33311W 6.REPLACE INPUT SHAFT BEARING

a.
C212164N01
2.586,0.446 2.939,0.675 0.352,0.229 10 SST 1.823,0.841 2.359,0.526 false 2.359,0.526 2.538,0.526 false

Using SST, remove the input shaft bearing.

SST
09303-35011  


b.
C212165N01
2.684,0.435 3.095,0.621 0.411,0.186 10 SST 1.75,0.884 2.338,0.518 false 2.338,0.518 2.616,0.518 false

Using SST and a hammer, install a new input shaft bearing.

SST
09304-12012  

HINT:

After installing the input shaft bearing to the engine side, make sure that it rotates smoothly.