Home › Drivetrain › CLUTCH › CLUTCH UNIT (for 1HZ)
RM25T0E _52 Drivetrain _029901 CLUTCH _0136647 CLUTCH UNIT(for 1HZ) G

CLUTCH  CLUTCH UNIT(for 1HZ)  INSPECTION  


PROCEDURE

Hide 31250 1.INSPECT CLUTCH DISC ASSEMBLY

NOTICE:

When replacing the clutch disc assembly, make sure to perform an inspection of the flywheel sub-assembly and clutch cover assembly.


a.
C215532

Using a vernier caliper, measure the rivet head depth.

Minimum rivet head depth:

0.3 mm (0.0119 in.)


If the depth is less than the minimum, replace the clutch disc assembly.


b.
C114037

Using a dial indicator, check the disc runout.

Maximum runout:

0.8 mm (0.0314 in.)


NOTICE:

Be sure to measure on the correct side of the clutch disc.


If the runout is more than the maximum, replace the clutch disc assembly.


Hide 31210 2.INSPECT CLUTCH COVER ASSEMBLY

a.
C215533C03
1.104,0.271 1.396,0.521 0.292,0.25 10 false *a 0.604,0.948 0.885,1.177 0.281,0.229 10 false *b
*a Width
*b Depth


Using a vernier caliper, measure the depth and width of the worn areas of the diaphragm spring.

Maximum width:

6.0 mm (0.236 in.)


Maximum depth:

0.5 mm (0.0197 in.)


If the depth or width is more than the maximum, replace the clutch cover assembly.


b.
A272260C01
1.833,0.479 2.938,0.479 true 1.833,1.698 2.938,1.698 true 2.958,0.385 3.156,0.552 0.198,0.167 10 false *a 2.958,1.615 3.156,1.781 0.198,0.167 10 false *b
*a Hair cracks, scratches or discoloration
*b Hair cracks, discoloration or excessive wear


Perform a visual inspection of the clutch cover assembly.

i.

Inspect for hair cracks or scratches extending from the center outwards, or discoloration.


ii.

Inspect for hair cracks in a circular pattern, discoloration or excessive wear.

If there is any damage, replace the clutch cover assembly.



Hide 13405 3.INSPECT FLYWHEEL SUB-ASSEMBLY

a.
Q007250

Using a dial indicator, measure the flywheel runout.

Maximum runout:

0.1 mm (0.00393 in.)


If the runout is more than the maximum, replace the flywheel sub-assembly.


b.
C313760C01
2.167,0.698 2.969,0.698 true 1.865,1.708 2.979,1.708 true 3.021,0.625 3.333,0.823 0.313,0.198 10 false *a 3.073,1.625 3.385,1.823 0.313,0.198 10 false *b
*a Hair cracks, scratches or discoloration
*b Hair cracks, discoloration or excessive wear


Perform a visual inspection of the flywheel sub-assembly.

i.

Inspect for hair cracks or scratches extending from the center outwards, or discoloration.


ii.

Inspect for hair cracks in a circular pattern, discoloration or excessive wear.

If there is any damage, replace the flywheel sub-assembly.



Hide 31230 4.INSPECT CLUTCH RELEASE BEARING ASSEMBLY

a.
C313350

Turn the release bearing by hand while applying force in the axial direction.

HINT:

The bearing is permanently lubricated and requires no cleaning or lubrication.

Replace the clutch release bearing assembly as necessary.



Hide 33311W 5.INSPECT INPUT SHAFT BEARING

a.
C313349

Turn the bearing by hand while applying rotational force and check that the bearing rotates smoothly.

If the bearing sticks or a considerable amount of resistance is felt, replace the input shaft front bearing.

HINT:

The bearing is permanently lubricated and requires no cleaning or lubrication.



Hide 33311W 6.REPLACE INPUT SHAFT BEARING

a.

Remove any 2 diametrically opposite bolts.


b.
Q007150N02
1.521,0.583 1.979,0.292 true 2.021,0.177 2.448,0.438 0.427,0.26 10 false SST

Using SST, remove the input shaft bearing.

SST
09303-35011  


c.
Q007151N02
1.396,0.156 1.219,0.156 1.219,0.156 1.219,0.844 true 1.458,0.063 1.948,0.281 0.49,0.219 10 false SST

Using SST and a hammer, tap in a new input shaft bearing.

SST
09304-12012  

HINT:

After installing the bearing to the crankshaft, make sure that it rotates smoothly.



d.

Install the 2 bolts.

Torque:
127.4 N*m (1299 kgf*cm, 94 ft.*lbf)