Home › Drivetrain › AXLE AND DIFFERENTIAL › DIFFERENTIAL SYSTEM(w/ Differential Lock)
RM25T0E _52 Drivetrain _029907 AXLE AND DIFFERENTIAL _0136702 DIFFERENTIAL SYSTEM(w/ Differential Lock) G

AXLE AND DIFFERENTIAL  DIFFERENTIAL SYSTEM(w/ Differential Lock)  INSPECTION  


PROCEDURE

Hide 1.INSPECT DIFFERENTIAL LOCK SYSTEM

a.
C312234

Inspect the indicator light.

i.

Check that the indicator light lights up for approximately 1 second when the ignition switch is turned to ON.



b.

Inspect the differential lock operation.

i.

Jack up the vehicle and start the engine.


ii.

Shift the transfer shift lever to the L position.


iii.

When the differential lock control switch is set to the ON position, the indicator light turns on. Differential lock is applied to the rear wheel at this time.

HINT:

If the gears of the differential lock system are not meshed, the indicator light remains blinking, so rotate the tires to mesh the gears.



iv.

When the differential lock control switch is at the OFF position, the indicator light goes off. Differential lock is released for the rear wheel at this time.


v.
C312231C01
2.219,0.833 2.219,0.417 true 2.885,0.833 2.885,0.417 true 1.208,0.833 1.208,0.417 true 0.542,0.833 0.542,0.417 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 2.104,0.25 2.417,0.448 0.313,0.198 10 false M1 2.792,0.24 3.104,0.438 0.313,0.198 10 false M2 1.115,0.24 1.427,0.438 0.313,0.198 10 false M4 0.448,0.24 0.76,0.438 0.313,0.198 10 false M3
*a Component with harness connected
(to No. 2 4 Wheel Drive Control ECU)


Check the voltage between the terminals of the No. 2 4 wheel drive control ECU when switching the differential control switch with the speedometer registering approximately 8 km/h (5 mph) or more.

Tester Connection Condition Specified Condition
3 (M1) - 1 (M2) RR 0.5 V or less (No change)
7 (M3) - 5 (M4) FR.RR 0.5 V or less (No change)


vi.

Return the differential lock control switch to OFF.


vii.

Stop the engine and lower the vehicle.



Hide 2.CHECK WIRE HARNESS AND CONNECTOR

a.
C312233C01
0.594,0.854 0.594,0.438 true 0.594,1.771 0.594,1.354 true 2.406,0.854 2.406,0.438 true 1.75,1.75 1.75,1.333 true 0.823,1.771 0.823,1.354 true 0.833,0.854 0.833,0.438 true 2.417,1.75 2.417,1.333 true 1.5,0.854 1.5,0.438 true 2.167,0.865 2.167,0.448 true 2.854,0.844 2.854,0.427 true 1.26,0.865 1.26,0.448 true 1.969,1.76 1.969,1.344 true 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a 0.479,0.26 0.792,0.458 0.313,0.198 10 false M2 0.521,1.781 0.833,1.979 0.313,0.198 10 false IG 2.323,0.26 2.635,0.458 0.313,0.198 10 false RF 1.708,1.76 2.021,1.958 0.313,0.198 10 false R 0.74,1.781 1.052,1.979 0.313,0.198 10 false FLP 0.719,0.26 1.031,0.458 0.313,0.198 10 false RLP 2.281,1.76 2.729,1.958 0.448,0.198 10 false 4WD 1.385,0.271 1.698,0.469 0.313,0.198 10 false SPD 2.063,0.26 2.375,0.458 0.313,0.198 10 false M4 2.75,0.25 3.063,0.448 0.313,0.198 10 false M3 1.135,0.271 1.448,0.469 0.313,0.198 10 false M1 1.844,1.76 2.26,1.958 0.417,0.198 10 false GND
*a Component without harness connected
(to No. 2 4 Wheel Drive Control ECU)


Inspect the system circuit with the connector disconnected.

i.

Disconnect the connector from the No. 2 4 wheel drive control ECU and inspect the connector on the wire harness side as shown in the table.

Standard Voltage
Tester Connection Trouble Part Condition Specified Condition
3 (M1) - 1 (M2) Rear differential lock actuator - Less than 100 Ω
7 (M3) - 5 (M4) Front differential lock actuator
13 (GND) - Body ground Body ground - Below 1 Ω
4 (SPD) - Body ground Speed sensor Vehicle moves slowly 1 pulse generation per 40 cm (15.75 in.)
8 (IG) - Body ground Differential fuse Ignition switch ON 11 to 14 V*1
22 to 28 V*2
2 (RLP) - Body ground Rear differential lock indicator switch Ignition switch ON with indicator light ON About 0 V
Ignition switch ON with indicator light OFF 11 to 14 V*1
22 to 28 V*2
9 (FLP) - Body ground Front differential lock indicator switch Ignition switch ON with indicator light ON About 0 V
Ignition switch ON with indicator light OFF 11 to 14 V*1
22 to 28 V*2
15 (4WD) - Body ground 4WD position switch Ignition switch ON with transfer shift lever in H2 11 to 14 V*1
22 to 28 V*2
Ignition switch ON with transfer shift lever not in H2 About 0 V
12 (R) - Body ground Differential lock control switch Ignition switch ON with differential lock control switch RR 11 to 14 V*1
22 to 28 V*2
Ignition switch ON with differential lock control switch FR.RR 11 to 14 V*1
22 to 28 V*2
Ignition switch ON with differential lock control switch OFF About 0 V
6 (RF) - Body ground Ignition switch ON with differential lock control switch RR About 0 V
Ignition switch ON with differential lock control switch FR.RR 11 to 14 V*1
22 to 28 V*2
Ignition switch ON with differential lock control switch OFF About 0 V

*1: for 12 V battery

*2: for 24 V battery


HINT:

If the result is not as specified, check and repair or replace the malfunctioning part shown in the table above.




Hide 89533A 3.CHECK NO. 2 4 WHEEL DRIVE CONTROL ECU

a.
C312231C02
2.219,0.833 2.219,0.417 true 2.906,0.833 2.906,0.417 true 1.208,0.833 1.208,0.417 true 0.542,0.833 0.542,0.417 true 0.979,1.729 0.979,1.313 true 1.479,1.719 1.479,1.302 true 2.646,1.74 2.646,1.323 true 2.635,0.844 2.635,0.427 true 0.073,0.063 0.385,0.26 0.313,0.198 10 false *a 2.104,0.25 2.417,0.448 0.313,0.198 10 false M1 2.823,0.24 3.135,0.438 0.313,0.198 10 false M2 1.115,0.24 1.427,0.438 0.313,0.198 10 false M4 0.448,0.24 0.76,0.438 0.313,0.198 10 false M3 0.833,1.76 1.25,1.958 0.417,0.198 10 false 4WD 1.354,1.76 1.792,1.969 0.438,0.208 10 false GND 2.531,1.771 2.969,1.979 0.438,0.208 10 false FLP 2.51,0.24 2.948,0.448 0.438,0.208 10 false RLP
*a Component with harness connected
(to No. 2 4 Wheel Drive Control ECU)


Inspect the system circuit with the connector connected.

i.

Turn the ignition switch to ON.


ii.

Shift the transfer shift lever to the H4 or L4 position.


iii.

Using a voltmeter, measure the voltage when the differential lock control switch is in the position shown in the table.

Standard Voltage
Tester Connection Switch Position Specified Condition
15 (4WD) - 13 (GND) - 0.5 V or less
9 (FLP) - 13 (GND) FR.RR*1
2 (RLP) - 13 (GND) RR*1
3 (M1) - 1 (M2) OFF → RR *2 0.5 V or less → 11 to 14 V (approximately 1 second) → 0.5 V or less
*3 0.5 V or less → 22 to 28 V (approximately 1 second) → 0.5 V or less
1 (M2) - 3 (M1) RR → OFF
7 (M3) - 5 (M4) OFF → FR.RR
5 (M4) - 7 (M3) FR.RR → OFF

*1: The rear differential should be locked mechanically.

*2: for 12 V battery

*3: for 24 V battery


HINT:

If the result is not as specified, replace the No. 2 4 wheel drive control ECU.