Wear protective gloves. Sharp areas on the parts may injure your hands.
If the seat is set down in another location after removing it from the vehicle, the seat may tilt and damage the front inner seat track assembly RH or front outer seat track assembly RH due to the difference in shape between the left and right seat tracks.
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the RH side.
A bolt without a torque specification is showing the standard bolt chart
(See page)
71148 1.INSTALL FRONT SEAT CUSHION SILENCER
Clean the separate type front seat cushion spring assembly surface.
Install a new 2 front seat cushion silencers as shown in the illustration.
| *1 | Front Seat Cushion Silencer Pad | *2 | Separate Type Front Seat Cushion Spring Assembly |
| *a | R end | - | - |
Install the front seat cushion silencer pad so that it is aligned with the R end of the separate type front seat cushion spring assembly.
72053C 2.INSTALL RECLINING REMOTE CONTROL LEVER SUB-ASSEMBLY RH
Install the reclining remote control lever sub-assembly RH with the 2 bolts.
71511S 3.INSTALL SEPARATE TYPE FRONT SEAT CUSHION PAD
Install the separate type front seat cushion pad to the separate type front seat cushion spring assembly.
71071S 4.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Set the separate type front seat cushion cover in place.
| *1 | Hog Ring Pliers |
| *a | Cutout |
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 9 new hog rings as shown in the illustration.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
Install the hog rings at the cutouts if they are there.
| *1 | Hog Ring Pliers |
| *a | Cutout |
Set the front seat cushion cover with pad in place.
Using hog ring pliers, install the front seat cushion cover with pad to the separate type front seat cushion spring assembly with 11 new hog rings as shown in the illustration.
Be careful not to damage the front seat cushion cover with pad.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the front seat cushion cover with pad.
Install the hog rings at the cutouts if they are there.
72110A 5.INSTALL FRONT OUTER SEAT TRACK ASSEMBLY RH
w/ Seat track adjusting handle:
Temporarily install the front outer seat track assembly RH with the 2 bolts.
Operate the seat track adjusting handle to move the front outer seat track assembly RH to the foremost position.
Tighten the bolt.
Operate the seat track adjusting handle to move the front outer seat track assembly RH to the rearmost position.
Tighten the bolt.
w/ Seat track adjusting handle:
Temporarily install the front outer seat track assembly RH with the 2 bolts.
Move the front outer seat track assembly RH to the foremost position.
Tighten the bolt.
Move the front outer seat track assembly RH to the rearmost position.
Tighten the bolt.
72130A 6.INSTALL FRONT INNER SEAT TRACK ASSEMBLY RH
Use the same procedure described for the front outer seat track assembly RH.
71521A 7.INSTALL FRONT SEAT CUSHION SILENCER PAD (for Walk in Seat Type)
| *1 | Hog Ring Pliers |
Using hog ring pliers, install the front seat cushion silencer pad with 2 new hog rings as shown in the illustration.
72510D 8.INSTALL OUTER RECLINING SEAT ADJUSTER ASSEMBLY RH
Install the outer reclining seat adjuster assembly RH to the front seatback frame sub-assembly RH with the 2 bolts.
71551S 9.INSTALL SEPARATE TYPE FRONT SEATBACK PAD
Install the separate type front seatback pad to the front seatback frame sub-assembly RH.
71073S 10.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Set the separate type front seatback cover in place.
| *1 | Hog Ring Pliers |
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 3 new hog rings as shown in the illustration.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Attach the 2 hooks to connect the straps of the separate type front seatback cover.
Pass the straps of the separate type front seatback cover as shown in the illustration.
| *1 | Hog Ring Pliers |
w/o Front Seatback Panel:
Using hog ring pliers, install the separate type front seatback cover with 3 new hog rings as shown in the illustration.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
| *1 | Hog Ring Pliers |
w/ Front Seatback Panel:
Using hog ring pliers, install the separate type front seatback cover with 3 new hog rings as shown in the illustration.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Attach the 4 claws to install the 2 front seat headrest support assemblies.
74841B 11.INSTALL FRONT SEATBACK PANEL (w/ Front Seatback Panel)
Install the 4 screws and front seatback panel.
12.INSTALL FRONT SEATBACK ASSEMBLY
Install the center seat hinge spacer to separate type front seatback assembly.
Install the washer to separate type front seat cushion spring assembly.
Install the front seatback assembly with the 2 bolts.
Install a new E-ring.
Lift up the seatback and check that the outer reclining adjuster assembly is fixed in place.
for Walk in Seat Type, for Short Body:
| *1 | Stake Part |
Using pliers, stake the stake part of the front outer seat track assembly RH.
Tighten the nut to connect the seat track control cable assembly.
Connect the 2 cables with the clamp to the separate type front seat cushion spring assembly.
Install the tension spring.
for Walk in Seat Type, for Long Body:
Using pliers, stake the stake part of the front inner seat track assembly RH.
Tighten the nut to connect the seat track control cable assembly.
Connect the 2 cables with the clamp to the separate type front seat cushion spring assembly.
Install the tension spring.
| *1 | Stake Part |
Using pliers, stake the stake part of the outer reclining seat adjuster assembly RH.
Connect the reclining remote control cable with the bolt.
71811C 13.INSTALL RECLINING ADJUSTER COVER RH
Install the reclining adjuster cover RH with the 2 screws.