Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › 2014.08–2017.09
RM25T0E _55 Steering _029921 STEERING COLUMN _0136921 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 89783 1.REMOVE TRANSPONDER KEY AMPLIFIER (w/ Engine Immobiliser System)

a.
C214793C01
0.604,1.448 0.833,1.677 0.833,1.677 0.969,1.677 true 1.021,1.583 1.333,1.74 0.313,0.156 10 false *a
*a Protective Tape


Detach the 2 claws, slide the transponder key amplifier in the direction indicated by the arrow in the illustration and remove it from the steering column upper with switch bracket assembly.

HINT:

Tape the screwdriver tip before use.



Hide 2.REMOVE STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY

a.

Using a drill, drill a hole to insert a screw extractor into each steering lock bolt.


b.
C299696

Using a screw extractor, remove the 2 steering lock set bolts, steering column upper with switch bracket assembly and steering column upper clamp.


Hide 3.REMOVE IGNITION SWITCH LOCK CYLINDER ASSEMBLY

a.

Turn the ignition switch lock cylinder assembly to ACC.


b.
C214493C01
2.115,1.021 2.344,0.365 2.344,0.365 2.5,0.365 true 2.219,1.083 2.438,1.406 2.438,1.406 2.531,1.406 true 1.021,2.708 1.333,2.865 0.313,0.156 10 false *a 1.438,0.99 1.75,1.146 0.313,0.156 10 false *b 1.563,2.396 1.875,2.552 0.313,0.156 10 false *c 2.563,0.281 2.875,0.438 0.313,0.156 10 false *d 2.563,1.313 2.875,1.469 0.313,0.156 10 false *e
*a ACC
*b Push
*c Pull
*d Claw
*e Stopper


Insert a thin-bladed screwdriver into the hole of the steering column upper with switch bracket assembly as shown in the illustration and pull out the key until the claw of the ignition switch lock cylinder assembly contacts the stopper of the steering column upper with switch bracket assembly.

NOTICE:

Be sure to pull out the key until the claw firmly contacts the stopper. There will be problems later if the key is not pulled out until the claw of the ignition switch lock cylinder assembly contacts the stopper of the steering column upper with switch bracket assembly.



c.
C105483C02
2.177,0.51 2.427,0.24 true 2.438,0.104 2.75,0.26 0.313,0.156 10 true *a
*a Claw


Insert a thin-bladed screwdriver into the hole of the steering column upper with switch bracket assembly as shown in the illustration, push the thin-bladed screwdriver in the direction shown in the illustration to detach the claw and pull out the ignition switch lock cylinder assembly.


Hide 84052 4.REMOVE UNLOCK WARNING SWITCH ASSEMBLY

a.
C299697C01
1.708,1.833 1.458,1.833 1.458,1.833 1.208,0.938 true 1.781,1.76 2.094,1.958 0.313,0.198 10 false *a
*a Center Part


Push up the center part of the unlock warning switch assembly, detach the 2 claws and remove the unlock warning switch assembly.

HINT:

Slide the unlock warning switch assembly in the direction indicated by the arrow in the illustration to remove it.



Hide 84450 5.REMOVE IGNITION OR STARTER SWITCH ASSEMBLY

a.
C299698

Detach the 2 claws and remove the ignition or starter switch assembly from the steering column upper with switch bracket assembly.


Hide 45804J 6.REMOVE BREAK AWAY COLLAR SUB-ASSEMBLY

a.
C104462

Remove the 2 break away capsules and 2 break away collars from the break away bracket.


Hide 45262A 7.REMOVE TILT LEVER RETURN SPRING

a.
C312591C01
2.417,1.813 2.375,1.583 true 2.417,0.375 2.104,0.896 true 0.938,1.875 1.188,1.563 true 2.438,0.208 2.896,0.406 0.458,0.198 10 false SST 2.396,1.844 2.708,2.042 0.313,0.198 10 false *1 0.75,1.844 1.063,2.042 0.313,0.198 10 false *a
*1 Return Spring Damper
*a Cloth


Using SST, remove the tilt lever return spring from the break away bracket and steering tilt lever.

SST
09921-00011  

NOTICE:

Do not let the return spring damper fall off of the tilt lever return spring.


HINT:

To avoid spatter, cover the area with a cloth.



Hide 8.REMOVE TILT STEERING SUPPORT BOND CABLE

a.
C269086

Remove the 3 screws, steering column tube bracket and tilt steering support bond cable.


Hide 45261 9.REMOVE TILT STEERING JUMP UP SPRING

a.
C104453C01
2.313,1.208 2.75,1.479 true 2.792,1.438 3.104,1.635 0.313,0.198 10 false *a
*a Cloth


Using pliers, pull the tilt steering jump up spring in the direction indicated by the arrow in the illustration and remove it from the break away bracket.

HINT:

To avoid spatter, cover the area with a cloth.



Hide 45833 10.LOOSEN NO. 1 TILT STEERING ADJUSTING NUT

a.
C104454

Lock the steering tilt lever.


b.
C104852

Using a hammer and chisel, loosen the staked part of the No. 1 tilt steering adjusting nut.


c.
C299699

Loosen the No. 1 tilt steering adjusting nut.

NOTICE:

Be sure to only loosen the No. 1 tilt steering adjusting nut. Do not remove it.



Hide 45821B 11.REMOVE NO. 1 TILT STEERING SUPPORT REINFORCEMENT

a.
C104457

Remove the steering tilt lever bolt and No. 1 tilt steering support reinforcement from the steering tilt lever.

NOTICE:

The steering tilt lever bolt has a left-handed thread.



Hide 45831 12.REMOVE TILT NO. 1 LEVER LOCK BOLT

a.
C366123

Using an 8 mm socket hexagon wrench, loosen the No. 1 steering tilt lever lock bolt until it can be turned by hand.


b.
C299699

Remove the No. 1 tilt steering adjusting nut from the No. 1 steering tilt lever lock bolt.


c.
C104459

Remove the tilt steering rotor, thrust needle roller bearing and steering column tube stopper from the No. 1 steering tilt lever lock bolt.


d.
C104460

Remove the No. 1 steering tilt lever lock bolt, steering column tube stopper and steering tilt lever from the break away bracket.


Hide 45878A 13.REMOVE BREAK AWAY BRACKET

a.
C104461

Remove the break away bracket from the steering column upper tube.


Hide 45890A 14.REMOVE TILT STEERING PAWL ASSEMBLY

a.
C104463

Remove the tilt steering pawl assembly from the steering column upper tube.


Hide 45263 15.REMOVE NO. 1 STEERING COLUMN RING

a.
C214675C01
0.375,0.844 0.823,1.094 true 2.688,1.375 2.583,1.667 2.583,1.667 2.417,1.667 true 0.208,0.729 0.521,0.885 0.313,0.156 10 false *a 2.24,1.583 2.552,1.74 0.313,0.156 10 false *1
*1 No. 1 Steering Column Ring
*a Snap Ring Expander


Using a snap ring expander, remove the No. 1 steering column ring from the steering main shaft.

NOTICE:

Do not damage the steering main shaft assembly.



Hide 45204 16.REMOVE STEERING LOWER COLUMN TUBE ASSEMBLY

a.
C299700

Remove the steering column lower tube assembly from the steering column upper tube.


Hide 45765 17.REMOVE TELESCOPIC STEERING GUIDE

a.
C299701

Remove the telescopic steering guide from the steering column lower tube assembly.


Hide 45877A 18.REMOVE STEERING COLUMN BRACKET SPACER

a.
C312593C01
1.479,3.135 2.385,2.313 2.385,2.313 1.667,3.385 true 1.271,0.813 1.5,0.479 true 2.625,0.833 2.854,0.5 true 2.438,2.198 2.896,2.396 0.458,0.198 10 false SST 1.531,0.354 1.99,0.552 0.458,0.198 10 false SST 2.885,0.375 3.344,0.573 0.458,0.198 10 false SST

Using SST and a hammer, tap out the steering column bracket spacer from the steering column lower tube assembly.

SST
09201-10000  (09201-01080)
09950-70010  (09951-07100)


Hide 45813 19.REMOVE NO. 1 TILT STEERING SUPPORT COLLAR

a.
C104468

Remove the 2 No. 1 tilt steering support collars from the steering column lower tube assembly.


Hide 45210 20.REMOVE STEERING MAIN SHAFT ASSEMBLY

a.
C104470C02
0.573,0.625 0.917,1.26 true 2.521,1.417 2.313,1.688 2.313,1.688 2.156,1.688 true 0.417,0.479 0.729,0.635 0.313,0.156 10 false *a 1.958,1.615 2.271,1.771 0.313,0.156 10 false *1
*1 Steering Main Shaft Snap Ring
*a Snap Ring Expander


Using a snap ring expander, remove the steering main shaft snap ring from the steering main shaft.

NOTICE:

Do not damage the steering main shaft assembly.



b.

Remove the steering main shaft assembly from the steering column upper tube.