Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › 2014.08–2017.09
RM25T0E _55 Steering _029921 STEERING COLUMN _0136921 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 45210 1.INSTALL STEERING MAIN SHAFT ASSEMBLY

a.

Install the steering main shaft assembly to the steering column upper tube.


b.
C104470C02
0.573,0.625 0.917,1.26 true 2.521,1.417 2.313,1.688 2.313,1.688 2.156,1.688 true 0.417,0.479 0.729,0.635 0.313,0.156 10 false *a 1.958,1.615 2.271,1.771 0.313,0.156 10 false *1
*1 Steering Main Shaft Snap Ring
*a Snap Ring Expander


Using a snap ring expander, install a new steering main shaft snap ring to the steering main shaft assembly.

NOTICE:
·

Make sure the steering main shaft snap ring is securely installed to the groove.

·

Do not damage the steering main shaft assembly.




Hide 45813 2.INSTALL NO. 1 TILT STEERING SUPPORT COLLAR

a.
C104850C01
2.021,0.927 2.344,1.125 0.323,0.198 10 false *a 2.042,1.51 2.365,1.708 0.323,0.198 10 false *a
*a 15°


Install the 2 No. 1 tilt steering support collars to the steering column lower tube assembly.

NOTICE:

When installing the tilt steering support collar No. 1, make sure that the cutout portion is aligned as shown in the illustration.



Hide 45877A 3.INSTALL STEERING COLUMN BRACKET SPACER

a.
C299694C01
0.677,4 0.948,3.458 true 2.094,2 2.406,2.198 0.313,0.198 10 false *a 2.115,2.604 2.427,2.802 0.313,0.198 10 false *a 0.531,4.01 0.844,4.208 0.313,0.198 10 false *b
*a 15°
*b Cloth


Clamp the steering column bracket spacer and steering column lower tube assembly in a vise between a cloth and aluminum plates, and install the steering column bracket spacer to the steering column lower tube assembly using the vise.

NOTICE:

When installing the steering column bracket spacer, make sure that it is positioned so that the inner diameter is as shown in the illustration.



Hide 45765 4.INSTALL TELESCOPIC STEERING GUIDE

a.
C299702C03
1.042,0.396 1.146,0.313 true 0.406,0.344 0.49,0.385 true 0.781,0.865 1.052,0.865 true 1.104,0.198 1.417,0.354 0.313,0.156 10 false *a 1.083,0.781 1.396,0.938 0.313,0.156 10 false *a 0.26,0.25 0.573,0.406 0.313,0.156 10 false *a
*a Match


Align the 3 protrusions of the telescopic steering guide with the 3 holes of the steering column lower tube assembly and install the telescopic steering guide.


Hide 45204 5.INSTALL STEERING LOWER COLUMN TUBE ASSEMBLY

a.
C308111

Apply MP grease to the area of the steering main shaft assembly indicated by the arrow in the illustration.


b.
C308112

Install the steering column lower tube assembly to the steering column upper tube.


Hide 45263 6.INSTALL NO. 1 STEERING COLUMN RING

a.
C214675C03
0.375,0.844 0.823,1.094 true 2.688,1.375 2.583,1.667 2.583,1.667 2.417,1.667 true 0.208,0.729 0.521,0.885 0.313,0.156 10 false *a 2.24,1.583 2.552,1.74 0.313,0.156 10 false *b
*a Snap Ring Expander
*b No. 1 Steering Column Ring


Using a snap ring expander, install a new No. 1 steering column ring to the steering main shaft.

NOTICE:
·

Make sure the No. 1 steering column ring is securely installed to the groove.

·

Do not damage the steering main shaft assembly.




Hide 45890A 7.INSTALL TILT STEERING PAWL ASSEMBLY

a.
C104475

Install the tilt steering pawl assembly to the steering column upper tube.

NOTICE:

When installing the tilt steering pawl assembly, position the opening as shown in the illustration.



Hide 45878A 8.INSTALL BREAK AWAY BRACKET

a.
C104476

Apply MP grease to the sliding areas of the break away bracket and install it to the steering column upper tube.


Hide 45873 9.INSTALL STEERING COLUMN TUBE STOPPER

a.
C104477C01
2.302,0.656 2.219,0.313 2.219,0.313 2.354,0.375 true 2.063,0.167 2.552,0.323 0.49,0.156 10 false *a
*a Parallel


Apply MP grease to the sliding surface of the steering column tube stopper (the one with the groove) and install it to the break away bracket.

NOTICE:

Align the flat edge of the steering column tube stopper and the raised sliding area of the break away bracket as shown in the illustration.



b.
C104478C01
2.5,0.792 2.396,1.167 2.396,1.167 2.396,1.51 true 2.396,1.51 2.625,1.51 false 2.667,0.917 2.5,1.188 2.5,1.188 2.5,1.5 true 2.677,1.417 3.188,1.583 0.51,0.167 10 false *a
*a Parallel


Apply MP grease to the sliding surface of the steering column tube stopper (the one without the groove) and install it to the break away bracket.

NOTICE:

Align the flat edge of the steering column tube stopper and the raised sliding area of the break away bracket as shown in the illustration.



Hide 45831 10.INSTALL NO. 1 TILT LEVER LOCK BOLT

a.
C299703

Apply MP grease to the sliding surface of the steering tilt lever and install it to the No. 1 steering tilt lever lock bolt.


b.
C104480

Install the No. 1 steering tilt lever lock bolt to the break away bracket.

NOTICE:
·

Do not drop the steering column tube stopper.

·

Pass the No. 1 steering tilt lever lock bolt through the hole of the tilt steering pawl assembly.




c.
C299704

Apply MP grease to the sliding surface of the thrust needle roller bearing and install it to the No. 1 steering tilt lever lock bolt.


d.

Temporarily install the tilt steering rotor to the No. 1 steering tilt lever lock bolt with a new No. 1 tilt steering adjusting nut.


e.
C366124

Using an 8 mm socket hexagon wrench, tighten the No. 1 steering tilt lever lock bolt.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


Hide 45821B 11.INSTALL NO. 1 TILT STEERING SUPPORT REINFORCEMENT

a.
C104483

Install the No. 1 tilt steering support reinforcement to the steering tilt lever with the steering tilt lever bolt.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

The tightening direction for the steering tilt lever bolt is the tightening direction for bolts with a left-handed thread.



Hide 45833 12.TIGHTEN NO. 1 TILT STEERING ADJUSTING NUT

a.
C104454

Lock the steering tilt lever.


b.
C366125C01
0.188,0.24 0.5,0.438 0.313,0.198 10 false *a 2.708,1.604 3.021,1.802 0.313,0.198 10 false *b
*a Hold
*b Turn


Using an 8 mm socket hexagon wrench, hold the No. 1 steering tilt lever lock bolt in place and tighten the No. 1 tilt steering adjusting nut.

Torque:
3.0 N*m (31 kgf*cm, 27 in.*lbf)


c.
C216017

Using pliers, stake the No. 1 tilt steering adjusting nut as shown in the illustration.

NOTICE:

After staking the No. 1 tilt steering adjusting nut, make sure it is not loose.



Hide 45261 13.INSTALL TILT STEERING JUMP UP SPRING

a.
C104486C01
2.344,1.229 2.698,1.458 true 2.76,1.417 3.073,1.615 0.313,0.198 10 false *a
*a Cloth


Using pliers, move the tilt steering jump up spring in the direction indicated by the arrow in the illustration to install it to the break away bracket.

NOTICE:

To avoid spatter, cover the area with a cloth.



Hide 45262A 14.INSTALL TILT LEVER RETURN SPRING

a.
C312591C01
2.417,1.813 2.375,1.583 true 2.417,0.375 2.104,0.896 true 0.938,1.875 1.188,1.563 true 2.438,0.208 2.896,0.406 0.458,0.198 10 false SST 2.396,1.844 2.708,2.042 0.313,0.198 10 false *1 0.75,1.844 1.063,2.042 0.313,0.198 10 false *a
*1 Return Spring Damper
*a Cloth


Using SST, install the tilt lever return spring to the break away bracket and steering tilt lever.

SST
09921-00011  

NOTICE:
·

To avoid spatter, cover the area with a cloth.

·

Do not let the return spring damper fall off of the tilt lever return spring.




Hide 15.INSTALL TILT STEERING SUPPORT BOND CABLE

a.
C269086

Install the steering column tube bracket and tilt steering support bond cable with the 3 screws.


Hide 45804J 16.INSTALL BREAK AWAY COLLAR SUB-ASSEMBLY

a.
C104462

Install the 2 new break away collars and 2 break away capsules to the break away bracket.

NOTICE:

Do not compress the disc spring portion of the support collar.



Hide 84450 17.INSTALL IGNITION OR STARTER SWITCH ASSEMBLY

a.
C299698

Attach the 2 claws to install the ignition or starter switch assembly to the steering column upper with switch bracket assembly.


Hide 84052 18.INSTALL UNLOCK WARNING SWITCH ASSEMBLY

a.
C308113

Attach the 2 claws to install the unlock warning switch assembly to the steering column upper with switch bracket assembly.

HINT:

Move the unlock warning switch assembly in the direction indicated by the arrow in the illustration to install it.



Hide 19.INSTALL IGNITION SWITCH LOCK CYLINDER ASSEMBLY

a.

Turn the ignition switch lock cylinder assembly to ACC.


b.
C214540C01
2.771,1.063 3.083,1.219 0.313,0.156 10 false *a 2.292,0.365 2.604,0.521 0.313,0.156 10 false *b
*a LOCK
*b ACC


Insert the ignition switch lock cylinder assembly into the steering column upper with switch bracket assembly to install it.


c.

Check that the ignition switch lock cylinder assembly is securely fixed in place.


Hide 20.INSPECT STEERING LOCK OPERATION

a.
C103934

Remove the key and check that the steering lock operates.


b.
C214539C01
2.208,0.542 2.635,0.708 0.427,0.167 10 false *b 2.594,1.292 3.021,1.458 0.427,0.167 10 false *a
*a LOCK
*b ACC


Insert the key, turn the ignition switch to ACC and check that the steering lock disengages.


Hide 21.INSTALL STEERING COLUMN UPPER WITH SWITCH BRACKET ASSEMBLY

a.
C103936

Install the steering column upper with switch bracket assembly and steering column upper clamp with 2 new steering lock set bolts, and tighten the bolts until the heads break off.


Hide 89783 22.INSTALL TRANSPONDER KEY AMPLIFIER (w/ Engine Immobiliser System)

a.
C308114

Attach the 2 claws to install the transponder key amplifier to the steering column upper with switch bracket assembly.