Home › Engine / Hybrid System › 1HZ (STARTING) › STARTER (for 3.0 kW Type)
RM25T0E _51 Engine / Hybrid System _029899 1HZ STARTING _0136995 STARTER(for 3.0 kW Type) A

1HZ STARTING  STARTER(for 3.0 kW Type)  DISASSEMBLY  


PROCEDURE

Hide 28120 1.REMOVE STARTER YOKE ASSEMBLY

a.
A326016

Open the terminal cap.


b.

Remove the nut and disconnect the lead wire from the terminal C.


c.

Remove the 2 through bolts.


d.

Pull out the starter yoke assembly and starter commutator end frame together with the starter armature assembly.


e.

Remove the 2 O-rings from the starter yoke assembly.


Hide 28150 2.REMOVE MAGNET STARTER SWITCH ASSEMBLY

a.
A326017

Remove the 3 screws and magnet starter switch assembly from the starter drive housing assembly.


b.
A326018C01
0.625,0.479 0.771,0.177 0.771,0.177 0.875,0.177 false 1.75,0.385 1.823,0.146 1.823,0.146 1.927,0.146 false 2.021,0.719 2.125,0.406 2.125,0.406 2.229,0.406 false 2.49,0.844 2.625,0.521 2.625,0.521 2.729,0.521 false 2.875,0.906 3.042,0.646 3.042,0.646 3.146,0.646 false 1.615,2 1.719,2 1.719,2 1.938,1.729 false 2.729,1.917 2.833,1.917 2.833,1.917 3.01,1.656 false 2.958,1.396 3.063,1.396 3.063,1.396 3.156,1.167 false 0.969,0.115 1.281,0.271 0.313,0.156 10 false *1 1.969,0.063 2.281,0.219 0.313,0.156 10 false *2 2.281,0.323 2.594,0.479 0.313,0.156 10 false *3 2.802,0.438 3.115,0.594 0.313,0.156 10 false *4 3.198,0.573 3.385,0.729 0.188,0.156 10 false *5 2.76,1.323 3.073,1.479 0.313,0.156 10 false *6 1.406,1.917 1.719,2.073 0.313,0.156 10 false *7 2.531,1.844 2.844,2 0.313,0.156 10 false *8
*1 Starter Drive Housing Assembly
*2 Pinion Gear
*3 Idle Gear
*4 Retainer
*5 Clutch Roller
*6 Plate Washer
*7 Starter Clutch Sub-assembly
*8 Return Spring


Remove the pinion gear, idle gear, retainer, clutch roller, plate washer, return spring and starter clutch sub-assembly from the starter drive housing assembly.


c.
A326019C01
2.271,1.385 2.115,1.385 2.115,1.385 1.885,0.74 false 1.667,0.667 1.792,0.219 1.792,0.219 1.917,0.219 false 2.031,0.146 2.344,0.302 0.313,0.156 10 false *1 2.375,1.302 2.688,1.458 0.313,0.156 10 false *a
*1 Steel Ball
*a Magnet Hand


Using a magnet hand, remove the steel ball from the starter clutch sub-assembly hole.


Hide 28140 3.REMOVE STARTER BRUSH HOLDER ASSEMBLY

a.
A326020

Disconnect the 4 brushes from the starter brush holder assembly.

i.

Using a screwdriver, hold back the brush spring.


ii.

Disconnect the brush from the starter brush holder assembly.



b.
A326021

Remove the 4 screws and 4 brushes.


c.

Remove the starter brush holder assembly from the starter yoke assembly.


Hide 28160 4.REMOVE STARTER ARMATURE ASSEMBLY

a.

Remove the starter armature assembly with starter commutator end frame from the starter yoke assembly.


b.
A326022

Using a plastic-faced hammer, tap the starter commutator end frame to remove the starter armature assembly from the starter commutator end frame.


c.

Remove the dust protector from the starter commutator end frame.