Home › Engine / Hybrid System › 1HZ (STARTING) › STARTER (for 3.0 kW Type)
RM25T0E _51 Engine / Hybrid System _029899 1HZ STARTING _0136995 STARTER(for 3.0 kW Type) A

1HZ STARTING  STARTER(for 3.0 kW Type)  REASSEMBLY  


PROCEDURE

Hide 28160 1.INSTALL STARTER ARMATURE ASSEMBLY

a.

Install the dust protector to the starter commutator end frame.


b.

Apply high-temperature grease to the armature bearings.


c.
A326034

Using a press, press the starter armature assembly into the starter commutator end frame.


d.

Place a new O-ring in position on the starter yoke assembly.


e.
A326035C01
1.469,1.615 1.583,1.615 1.583,1.615 1.865,1.104 true 1.104,0.115 1.219,0.115 1.219,0.115 1.813,0.406 true 1.25,1.521 1.563,1.677 0.313,0.156 10 false *a 0.865,0.031 1.177,0.188 0.313,0.156 10 false *b
*a Claw
*b Groove


Align the claw of the starter yoke assembly with the groove of the starter commutator end frame, install the starter yoke assembly to the starter commutator end frame.


Hide 28140 2.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.
A326036C01
1.344,1.969 1.469,1.969 1.469,1.969 1.698,1.563 true 1.708,1.417 2.167,0.49 2.167,0.49 2.281,0.49 true 2.344,0.375 2.729,0.573 0.385,0.198 10 false *a 1.167,1.885 1.479,2.042 0.313,0.156 10 false *b
*a Claw
*b Groove


Align the claw of the starter brush holder assembly with the groove of the starter yoke assembly.


b.

Place the starter brush holder assembly on the starter yoke assembly.


c.

Install the 4 brushes with the 4 screws.

Torque:
3.6 N*m (37 kgf*cm, 32 in.*lbf)


d.

Connect the 4 brushes to the starter brush holder assembly.

i.

Using a screwdriver, hold back the spring.


ii.

Connect the brush to the starter brush holder assembly.

NOTICE:

Check that positive (+) lead wires are not grounded.




Hide 28011 3.INSTALL STARTER CLUTCH SUB-ASSEMBLY

a.
A326037C01
1.552,1.656 1.688,1.656 1.688,1.656 1.875,0.635 false 1.354,1.573 1.667,1.729 0.313,0.156 10 false *1
*1 Steel Ball


Apply high-temperature grease to the steel ball, return spring, idle gear, retainer and clutch roller.


b.

Insert the steel ball into the starter clutch sub-assembly hole.


c.

Insert the return spring into the starter clutch sub-assembly hole.


d.
A326097C01
2.521,0.604 2.792,0.26 2.792,0.26 2.896,0.26 false 2.823,1.563 2.708,1.563 2.708,1.563 2.448,0.969 true 2.323,1.844 2.208,1.844 2.208,1.844 1.781,1.094 true 2.958,0.188 3.271,0.344 0.313,0.156 10 false *1 2.896,1.479 3.208,1.635 0.313,0.156 10 false *a 2.396,1.76 2.708,1.917 0.313,0.156 10 false *b
*1 Plate Washer
*a Claw
*b Groove


Align the claw of the plate washer with the groove of the magnet starter switch assembly, install the plate washer to the magnet starter switch assembly.


e.
A326098C01
0.635,0.479 0.74,0.198 0.74,0.198 0.813,0.198 false 1.771,0.396 1.875,0.156 1.875,0.156 1.948,0.156 false 2.021,0.729 2.125,0.448 2.125,0.448 2.198,0.448 false 2.458,0.823 2.563,0.542 2.563,0.542 2.635,0.542 false 2.865,0.906 3.01,0.635 3.01,0.635 3.083,0.635 false 1.781,2.01 1.844,2.01 1.844,2.01 1.938,1.719 false 2.854,1.948 2.917,1.948 2.917,1.948 3.01,1.656 false 0.854,0.135 1.167,0.292 0.313,0.156 10 false *1 2.021,0.073 2.333,0.229 0.313,0.156 10 false *2 2.26,0.375 2.573,0.531 0.313,0.156 10 false *3 2.698,0.469 3.01,0.625 0.313,0.156 10 false *4 3.135,0.563 3.333,0.729 0.198,0.167 10 false *5 1.573,1.917 1.885,2.073 0.313,0.156 10 false *6 2.646,1.865 2.958,2.021 0.313,0.156 10 false *7
*1 Starter Drive Housing Assembly
*2 Pinion Gear
*3 Idle Gear
*4 Retainer
*5 Clutch Roller
*6 Starter Clutch Sub-assembly
*7 Return Spring


Place these parts in position on the starter drive housing assembly.


f.

Assemble the starter drive housing assembly and magnet starter switch assembly and install the 3 screws.

Torque:
11.3 N*m (115 kgf*cm, 8 ft.*lbf)


Hide 28120 4.INSTALL STARTER YOKE ASSEMBLY

a.

Place a new O-ring in position on the starter yoke assembly.


b.
A326038C01
2.146,0.635 2.375,0.417 2.375,0.417 2.479,0.417 true 1.729,0.406 1.958,0.188 1.958,0.188 2.063,0.188 true 2.542,0.323 2.854,0.479 0.313,0.156 10 false *a 2.135,0.135 2.448,0.292 0.313,0.156 10 false *b
*a Claw
*b Groove


Align the claw of the starter brush holder assembly with the groove of the magnet starter switch assembly, and install the starter yoke assembly.


c.

Install the starter yoke assembly and starter commutator end frame to the magnet starter switch assembly with the 2 through bolts.

Torque:
14.2 N*m (145 kgf*cm, 10 ft.*lbf)


d.

Connect the lead wire to the terminal C with the nut.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


e.

Close the terminal cap.