Home › Engine / Hybrid System › 1HZ (STARTING) › STARTER (for 2.5 kW, 4.5 kW Type)
RM25T0E _51 Engine / Hybrid System _029899 1HZ STARTING _0136996 STARTER(for 2.5 kW, 4.5 kW Type) G

1HZ STARTING  STARTER(for 2.5 kW, 4.5 kW Type)  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

Each of the following tests must be performed within 3 to 5 seconds to prevent the coil from burning out.


a.

Mount the starter assembly in a vise between aluminum plates.


b.

Perform a pull-in test.

i.

Remove the nut, and then disconnect the lead wire from terminal C.


ii.
A326075C02
0.375,2.031 0.583,2.031 false 1.188,2.375 1.417,2.542 1.417,2.542 1.542,2.542 true 1.615,2.438 1.927,2.594 0.313,0.156 10 false *a 0.177,1.948 0.49,2.104 0.313,0.156 10 false *b
*a Terminal 50
*b Terminal C


Connect the battery to the magnet starter switch assembly as shown in the illustration. Then check that the clutch pinion gear moves outward.

If the clutch pinion gear does not move, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



c.
A326076C02
0.583,2.677 0.688,2.677 0.688,2.677 0.76,2.104 true 0.396,2.594 0.708,2.75 0.313,0.156 10 false *a
*a Terminal C


Perform a holding test.

i.

Disconnect the negative (-) terminal lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains out.

If the clutch pinion gear returns inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



d.
A326077

Inspect the clutch pinion gear return.

i.

Disconnect the negative (-) terminal lead from the starter body. Check that the clutch pinion gear returns inward.

If the clutch pinion gear does not return inward, inspect the magnet starter switch assembly. If the magnet starter switch assembly is not as specified, replace it.



e.

Perform an operation test without load.

i.

Connect the lead wire to terminal C.

Torque:
5.9 N*m (60 kgf*cm, 52 in.*lbf)


ii.
A326078C01
1.135,1.292 1.229,1.583 1.229,1.583 1.333,1.583 true 1.323,1.073 1.729,1.073 true 1.802,0.99 2.115,1.146 0.313,0.156 10 false *a 1.354,1.5 1.667,1.656 0.313,0.156 10 false *b
*a Terminal 30
*b Terminal 50


Connect the battery and an ammeter to the starter assembly as shown in the illustration.


iii.

Check that the starter rotates smoothly and steadily while the pinion gear is extended. Then measure the current.

Specified current:
for 12 V Type:

180 A or less at 11 V

for 24 V Type:

90 A or less at 23 V


If the result is not as specified, replace the starter assembly.

HINT:

Inspect the starter brush holder assembly, starter yoke assembly and starter armature assembly. If there is a malfunction, replace the part and perform this test again.




Hide 28150 2.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.
A326067C01
1.542,1.688 1.708,1.688 1.708,1.688 1.958,1.271 false 0.677,0.344 0.802,0.344 0.802,0.344 1.094,0.656 false 0.427,0.24 0.74,0.396 0.313,0.156 10 false *a 1.26,1.625 1.573,1.781 0.313,0.156 10 false *b
*a Terminal C
*b Terminal 50


Inspect the pull-in coil.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the result is not as specified, replace the magnet starter switch assembly.



b.
A326068C01
1.167,0.167 1.281,0.167 1.281,0.167 1.563,0.427 true 1.521,1.771 1.688,1.771 1.688,1.771 1.938,1.354 true 0.927,0.073 1.24,0.229 0.313,0.156 10 false *a 1.281,1.688 1.594,1.844 0.313,0.156 10 false *b
*a Switch Body
*b Terminal 50


Inspect the holding coil.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Switch body Always Below 2 Ω


If the result is not as specified, replace the magnet starter switch assembly.



Hide 3.INSPECT BRUSH

a.
A326056C01
0.042,0.063 0.354,0.219 0.313,0.156 10 false *a 1.635,0.104 1.948,0.26 0.313,0.156 10 false *b
*a Brush Holder Side
*b Starter Yoke Side


Using a vernier caliper, measure the brush length.

Standard length:

20.5 mm (0.807 in.)


Minimum length:

11.0 mm (0.433 in.)


If the length is less than the minimum, replace the starter brush holder assembly and starter yoke assembly.


Hide 28140 4.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.

Check the brush spring load.

i.
A321559

Take a pull scale reading immediately after the brush spring separates from the brush.

Standard spring load:

26 to 45 N (3 to 5 kgf, 5.8 to 10.1 lbf)


Minimum spring load:

12 N (1 kgf, 2.8 lbf)


If the spring load is less than the minimum, replace the starter brush holder assembly.



b.
A326057

Inspect the insulation.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) brush holder - Negative (-) brush holder Always 10 kΩ or higher


If the result is not as specified, replace the starter brush holder assembly.



Hide 28120 5.INSPECT STARTER YOKE ASSEMBLY

a.

Inspect the field coil for an open circuit.

i.
A326054

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Lead Wire - Brush Always Below 1 Ω


If the result is not as specified, replace the starter yoke assembly.


ii.
A326055

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Starter yoke body - Brush Always 10 kΩ or higher


If the result is not as specified, replace the starter yoke assembly.



Hide 28160 6.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator for dirt and/or burns on the surface.

If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.


b.
A326050C01
1.01,0.25 1.156,0.25 1.156,0.25 1.302,0.521 true 0.75,0.156 1.063,0.313 0.313,0.156 10 false *a
*a Segment


Inspect the commutator for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



c.

Inspect the commutator for a short circuit.

i.
A326051C01
0.667,0.292 0.771,0.292 0.771,0.292 0.938,0.573 true 1.385,0.125 1.49,0.125 1.49,0.125 1.656,0.406 true 0.469,0.208 0.781,0.365 0.313,0.156 10 false *a 1.188,0.063 1.5,0.219 0.313,0.156 10 false *b
*a Segment
*b Coil Core


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Coil core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



d.
A326052

Check the commutator circle runout.

i.

Place the commutator on V-blocks.


ii.

Using a dial indicator, measure the circle runout.

Maximum circle runout:

0.05 mm (0.00197 in.)


If the circle runout is more than the maximum, replace the starter armature assembly.



e.
A326053

Using a vernier caliper, measure the commutator diameter.

Standard diameter:

36.0 mm (1.42 in.)


Minimum diameter:

35.0 mm (1.38 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


f.
A102634

Using a vernier caliper, measure the undercut depth of the commutator.

Standard undercut depth:

0.7 mm (0.0276 in.)


Minimum undercut depth:

0.2 mm (0.00787 in.)


If the undercut depth is less than the minimum, replace the starter armature assembly.


Hide 28011 7.INSPECT STARTER CLUTCH SUB-ASSEMBLY

a.
A326058C01
2.104,0.813 2.323,0.969 0.219,0.156 10 true *a 1.604,1.198 1.813,1.354 0.208,0.156 10 true *b
*a Free
*b Lock


Rotate the pinion gear clockwise and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.

If the result is not as specified, replace the starter clutch sub-assembly.


b.

Turn the pinion gear by hand while applying inward force and check the movement of the bearing.

If resistance is felt or the bearing sticks, replace the starter clutch sub-assembly.