Home › Engine / Hybrid System › 1HZ (STARTING) › STARTER (for 2.5 kW, 4.5 kW Type)
RM25T0E _51 Engine / Hybrid System _029899 1HZ STARTING _0136996 STARTER(for 2.5 kW, 4.5 kW Type) A

1HZ STARTING  STARTER(for 2.5 kW, 4.5 kW Type)  DISASSEMBLY  


PROCEDURE

Hide 28120 1.REMOVE STARTER YOKE ASSEMBLY

a.

Open the terminal cap.


b.
A326044

Remove the nut and disconnect the lead wire from the terminal C.


c.

Remove the 2 through bolts.


d.

Pull out the starter yoke and starter commutator end frame together with the starter armature assembly.


e.
A326073

Remove the felt washer from the starter armature assembly.


Hide 28150 2.REMOVE MAGNET STARTER SWITCH ASSEMBLY

a.
A326045

Remove the 3 screws and magnet starter switch assembly from the starter drive housing assembly.


b.
A326046C02
2.5,0.104 2.615,0.104 2.615,0.104 2.823,0.365 false 1.802,0.604 1.563,0.25 1.563,0.25 1.448,0.25 false 2.177,0.531 2.021,0.146 2.021,0.146 1.906,0.146 false 2.917,1.333 2.813,1.333 2.813,1.333 2.625,0.74 false 0.625,0.458 0.448,0.229 0.448,0.229 0.333,0.229 false 2.302,1.646 2.188,1.646 2.188,1.646 1.99,1.24 false 0.146,0.156 0.458,0.313 0.313,0.156 10 false *1 2.406,1.573 2.719,1.729 0.313,0.156 10 false *2 1.708,0.073 2.021,0.229 0.313,0.156 10 false *3 2.99,1.271 3.208,1.427 0.219,0.156 10 false *4 2.344,0.042 2.521,0.219 0.177,0.177 10 false *5 1.229,0.167 1.417,0.323 0.188,0.156 10 false *6
*1 Magnet Starter Switch Assembly
*2 Return Spring
*3 Clutch Roller
*4 Retainer
*5 Idle Gear
*6 Plate Washer


Remove the idle gear, retainer, clutch roller, plate washer and return spring from the magnet starter switch assembly.


c.
A326047C01
2.49,1.125 2.76,0.708 2.76,0.708 2.906,0.708 false 2.417,1.938 2.563,1.938 2.563,1.938 2.719,1.427 false 3.021,0.635 3.24,0.802 0.219,0.167 10 false *1 2.219,1.865 2.531,2.021 0.313,0.156 10 false *a
*1 Steel Ball
*a Magnet Hand


Using a magnet hand, remove the steel ball from the starter drive housing assembly.


Hide 28140 3.REMOVE STARTER BRUSH HOLDER ASSEMBLY

a.
A326048

Remove the 2 screws, and then remove the commutator end frame from the starter yoke assembly.

NOTICE:

While holding down the lead wire, remove the starter commutator end frame.



b.

Remove the dust protector from the starter commutator end frame assembly.


c.
A326049

Disconnect the 4 brushes from the starter brush holder assembly.

i.

Using a screwdriver, hold back the brush spring.


ii.

Disconnect the brush from the starter brush holder assembly.



d.

Remove the starter brush holder assembly.


Hide 28160 4.REMOVE STARTER ARMATURE ASSEMBLY

a.

Remove the starter armature assembly from the starter yoke assembly.