Home › Engine / Hybrid System › 1HZ (STARTING) › STARTER (for 2.5 kW, 4.5 kW Type)
RM25T0E _51 Engine / Hybrid System _029899 1HZ STARTING _0136996 STARTER(for 2.5 kW, 4.5 kW Type) A

1HZ STARTING  STARTER(for 2.5 kW, 4.5 kW Type)  REASSEMBLY  


PROCEDURE

Hide 28160 1.INSTALL STARTER ARMATURE ASSEMBLY

a.

Install the starter armature assembly to the starter yoke assembly.


Hide 28140 2.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.

Install the starter brush holder assembly.


b.

Connect the 4 brushes to the starter brush holder assembly.

i.

Using a screwdriver, hold back the spring.


ii.

Connect the brush to the starter brush holder assembly.

NOTICE:

Check that positive (+) lead wires are not grounded.




c.

Install the dust protector to the starter commutator end frame.


d.

Install the starter commutator end frame to the starter yoke assembly with the 2 screws.

Torque:
3.6 N*m (37 kgf*cm, 32 in.*lbf)


Hide 28150 3.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.

Apply high-temperature grease to the steel ball, return spring, idle gear, retainer and clutch roller.


b.
A326070

Insert the steel ball into the starter drive housing assembly.


c.
A326072C01
1.531,0.333 1.625,0.333 1.625,0.333 1.802,0.625 false 1.958,0.25 2.052,0.25 2.052,0.25 2.177,0.542 false 2.854,1.177 2.729,1.177 2.729,1.177 2.583,0.74 false 3.146,0.969 3.052,0.969 3.052,0.969 3.01,0.75 false 2.51,1.625 2.385,1.625 2.385,1.625 2.24,1.188 false 2.375,1.938 2.25,1.938 2.25,1.938 1.896,0.979 true 1.75,1.958 1.625,1.958 1.625,1.958 1.25,1.115 true 1.344,0.25 1.656,0.406 0.313,0.156 10 false *1 1.76,0.177 2.073,0.333 0.313,0.156 10 false *2 2.896,1.104 3.094,1.292 0.198,0.188 10 false *3 3.188,0.896 3.375,1.073 0.188,0.177 10 false *4 2.625,1.563 2.938,1.719 0.313,0.156 10 false *5 1.802,1.885 2.115,2.042 0.313,0.156 10 false *b 2.448,1.844 2.76,2 0.313,0.156 10 false *a
*1 Plate Washer
*2 Clutch Roller
*3 Retainer
*4 Idle Gear
*5 Return Spring
*a Claw
*b Groove


Align the claw of the plate washer with the groove of the magnet starter switch assembly, install the plate washer, clutch roller, retainer, idle gear and return spring to the magnet starter switch assembly.


d.

Install the magnet starter switch assembly to the starter drive housing assembly with the 3 screws.

Torque:
9.3 N*m (95 kgf*cm, 82 in.*lbf)


Hide 28120 4.INSTALL STARTER YOKE ASSEMBLY

a.

Install the felt washer to the starter armature assembly.


b.
A326074C01
2.292,1.469 2.469,1.844 2.469,1.844 2.594,1.844 true 0.927,1.396 1.073,1.854 1.073,1.854 1.188,1.854 true 2.677,1.76 2.99,1.917 0.313,0.156 10 false *a 1.24,1.76 1.552,1.917 0.313,0.156 10 false *b
*a Claw
*b Groove


Align the claw of the starter yoke assembly with the groove of the magnet starter switch assembly.


c.

Install the starter yoke assembly and starter commutator end frame to the magnet starter switch assembly with the 2 through bolts.

Torque:
9.3 N*m (95 kgf*cm, 82 in.*lbf)


d.

Connect the lead wire to the terminal C with the nut.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


e.

Close the terminal cap.