Home › Engine / Hybrid System › 1VD-FTV (STARTING) › STARTER
RM25T0E _51 Engine / Hybrid System _029900 1VD-FTV STARTING _0137002 STARTER G

1VD-FTV STARTING  STARTER  INSPECTION  


PROCEDURE

Hide 28100 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

The following tests must be done within 3 to 5 seconds to prevent the coil from burning out.


a.

Perform operation test without load.

A289429C01
5.031,0.948 5.438,1.219 5.438,1.219 5.563,1.219 true 4.344,0.177 4.479,0.177 4.479,0.177 4.646,0.823 true 4.156,0.115 4.469,0.271 0.313,0.156 10 false *a 5.656,1.135 5.969,1.292 0.313,0.156 10 false *b
*a Terminal 50 *b Terminal 30


i.

Mount the starter assembly in a vise between aluminum plates.


ii.

Connect the battery and an ammeter to the starter assembly with terminal 30 disconnected as shown in the illustration.

NOTICE:

Do not connect terminal 30 to the battery.



iii.

Connect terminal 30 to the battery and check that the starter rotates smoothly and steadily while the pinion gear is moving outward. Then measure the current.

Standard current:

200 A or less at 11 V


If the result is not as specified, repair or replace the starter assembly.



Hide 28160 2.INSPECT STARTER ARMATURE ASSEMBLY

a.
A165485C01
1.802,1.563 2.292,2.042 2.292,2.042 2.427,2.042 true 2.5,1.948 2.813,2.104 0.313,0.156 10 false *a
*a Segment


Inspect the commutator for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



b.
A165486C01
2.573,0.906 2.969,1.74 2.969,1.74 3.083,1.74 true 1.729,1.448 2.125,2.052 2.125,2.052 2.24,2.052 true 2.302,1.979 2.615,2.135 0.313,0.156 10 false *a 3.146,1.667 3.365,1.833 0.219,0.167 10 false *b
*a Segment
*b Coil Core


Inspect the commutator for a short circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Coil core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



c.
A161636

Using a vernier caliper, measure the commutator diameter.

Standard diameter:

36.0 mm (1.42 in.)


Minimum diameter:

35.0 mm (1.38 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


d.
A115027

Using a vernier caliper, measure the undercut depth of the commutator.

Standard undercut depth:

0.7 mm (0.0276 in.)


Minimum undercut depth:

0.2 mm (0.00787 in.)


If the undercut depth is less than the minimum, correct it with a hacksaw blade.


e.
A154803

Check that the bearing rotates smoothly.

If necessary, replace the starter armature assembly.


f.
A154804

Inspect the commutator circle runout.

i.

Place the commutator on V-blocks.


ii.

Using a dial indicator, measure the circle runout.

Maximum circle runout:

0.05 mm (0.00197 in.)


If the runout is more than the maximum, correct it with sandpaper (#400) or replace the starter armature assembly.



Hide 28120 3.INSPECT STARTER YOKE ASSEMBLY

a.

Inspect the field coil for an open circuit.

i.
A292476

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal C - Brushes Always Below 1 Ω


If the result is not as specified, replace the starter yoke assembly.



b.

Inspect if the field coil is grounded.

i.
A292477

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Brushes - Starter yoke body Always 10 kΩ or higher


If the result is not as specified, replace the starter yoke assembly.



Hide 4.INSPECT STARTER BRUSH

a.
A292478C01
0.073,0.073 0.271,0.26 0.198,0.188 10 false *a 0.094,2.396 0.292,2.583 0.198,0.188 10 false *b 0.729,1.958 0.906,2.115 0.177,0.156 10 false *c 2.385,4.25 2.552,4.406 0.167,0.156 10 false *c
*a Brush Holder Side
*b Starter Yoke Side
*c Length


Using a vernier caliper, measure the brush length.

Standard length:

21.0 mm (0.827 in.)


Minimum length:

12.0 mm (0.472 in.)


If the length is less than the minimum, replace the starter brush holder assembly and starter yoke assembly.


Hide 28140 5.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.
P021088E09
1.688,0.375 1.844,0.573 0.156,0.198 10 false .

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) brush holder - Negative (-) brush holder Always 10 kΩ or higher


If the result is not as specified, replace the starter brush holder assembly.


b.
A321559

Inspect the load of the brush spring.

i.

Take the pull scale reading immediately after the brush spring separates from the brush.

Standard spring installed load:

36 N (4 kgf, 8.1 lbf)


Minimum spring installed load:

12 N (1 kgf, 2.8 lbf)


If the spring installed load is less than the minimum, replace the starter brush holder assembly.



Hide 28011 6.INSPECT STARTER CLUTCH SUB-ASSEMBLY

a.

Check the starter clutch operation.

i.
A163083C01
1.781,1.635 1.979,1.813 0.198,0.177 10 false *b 1.906,0.573 2.104,0.729 0.198,0.156 10 false *a
*a Free
*b Lock


Hold the clutch and bearing with one hand and turn the shaft with the other. Check that the inner sleeve turns easily in the "free" direction but cannot turn in the "lock" direction as shown in the illustration.

If the starter clutch sub-assembly does not operate as specified, replace the starter clutch sub-assembly.



Hide 28150 7.INSPECT MAIN SWITCH ASSEMBLY

a.

Check the pull-in coil for an open circuit.

i.
A161641C01
1.531,0.271 1.146,0.115 1.146,0.115 1.042,0.115 true 1.542,0.615 1.115,1.188 1.115,1.188 1.021,1.188 true 0.781,0.063 0.979,0.24 0.198,0.177 10 false *a 0.76,1.104 0.969,1.26 0.208,0.156 10 false *b
*a Terminal 50
*b Terminal C


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the result is not as specified, replace the main switch assembly.



b.
A161642C01
1.021,0.281 1.688,0.896 1.688,0.896 1.823,0.896 true 1.656,1.594 1.938,1.927 1.938,1.927 2.073,1.927 false 1.885,0.813 2.063,0.99 0.177,0.177 10 false *a 2.146,1.844 2.302,2 0.156,0.156 10 false *b
*a Terminal 50
*b Housing Body


Check the hold-in coil for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Housing Body Always Below 2 Ω


If the result is not as specified, replace the main switch assembly.