Home › Steering › STEERING GEAR / LINKAGE › STEERING LINKAGE › 2014.08–2016.08
RM25T0E _55 Steering _029923 STEERING GEAR / LINKAGE _0136923 STEERING LINKAGE A

STEERING GEAR / LINKAGE  STEERING LINKAGE  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 45045 1.INSTALL STEERING RELAY ROD END SUB-ASSEMBLY LH

a.

When reassembling steering relay rod end:

i.
C162818C01
1.344,1.01 1.292,1.396 1.292,1.396 1.698,1.156 false 1.948,1.135 2.156,0.906 false 1.885,1.615 2.115,1.365 false 2.365,1.344 2.635,1.073 false 2.594,1.406 3.063,1.229 3.063,1.229 3.198,1.719 false 1.615,0.823 1.823,0.594 false 3.042,1.063 3.25,1.26 0.208,0.198 10 false *1 2.646,0.948 2.958,1.104 0.313,0.156 10 false *2 1.146,1.375 1.458,1.531 0.313,0.156 10 false *3 1.854,0.49 2.167,0.646 0.313,0.156 10 false *4 2.146,0.771 2.458,0.927 0.313,0.156 10 false *5 1.708,1.594 2.021,1.75 0.313,0.156 10 false *6
*1 Relay Rod Set Ring
*2 Steering Link Joint Straight Screw Plug
*3 Ball Stud Seat
*4 Steering Link Joint Knob
*5 Steering Link Joint Compression Spring
*6 Steering Link Joint Spring Seat


Apply MP grease to the joint parts.


ii.

Install the steering link joint compression spring, steering link joint spring seat, steering link joint knob, 2 ball stud seats and steering link joint screw plug.


iii.

Tighten the steering link joint screw plug fully, and then loosen the steering link joint screw plug 1/2 turn.


iv.

Install a new relay rod set ring.


v.

Pack the steering relay rod end with MP grease.

Grease capacity:

4.8 to 6.2 g (0.170 to 0.218 oz.)




b.

Screw the steering relay rod end into the steering relay rod.


Hide 45044 2.INSTALL STEERING RELAY ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 45450 3.ADJUST STEERING RELAY ROD ASSEMBLY

a.
C308116C01
2.583,1.042 2.74,1.24 0.156,0.198 10 false A' 0.979,1.042 1.135,1.24 0.156,0.198 10 false A 1.417,1.063 1.885,1.26 0.469,0.198 10 false A = A' 1.542,0.729 1.698,0.927 0.156,0.198 10 false *a
*a Length


Turn the steering relay rod ends equal amounts into the steering relay rod, and adjust the length of the steering relay rod.

Length:

1107.5 to 1110.5 mm (3.633 to 3.642 ft.)



b.

Temporarily tighten the bolts or nuts to fix the clamps in place so that the steering relay rod ends are as shown in the illustration.


Hide 45047 4.INSTALL TIE ROD END SUB-ASSEMBLY LH

a.

Screw the tie rod end LH into the tie rod.


Hide 45046 5.INSTALL TIE ROD END SUB-ASSEMBLY RH

a.

Screw the tie rod end RH into the tie rod.


Hide 45460A 6.ADJUST TIE ROD ASSEMBLY

a.
C299713C01
1.583,0.792 1.896,0.948 0.313,0.156 10 false *a 2.458,1.208 2.771,1.365 0.313,0.156 10 false A' 0.813,1.229 1.125,1.385 0.313,0.156 10 false A 1.479,1.25 2.063,1.448 0.583,0.198 10 false A = A'
*a Length


Turn the tie rod ends equal amounts into the steering tie rod, and adjust the length of the steering tie rod.

Length:

1184.5 mm (3.89 ft.)



b.

Temporarily tighten the bolts or nuts to fix the clamps in place so that the rod ends are as shown in the illustration.


c.

After toe-in adjustment, tighten the 2 bolts and 2 nuts to tighten the 2 clamps.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)


Hide 44251 7.INSTALL PITMAN ARM

a.
C162812C01
1.354,1.01 0.854,0.469 0.854,0.469 1.604,1.01 true 2.313,0.427 2.125,0.427 2.125,0.427 1.781,0.885 true 2.208,1.75 1.865,1.75 true 0.667,0.354 1.552,0.573 0.885,0.219 10 false *a 2.292,1.656 3.042,1.875 0.75,0.219 10 false *2 2.417,0.344 3.219,0.563 0.802,0.219 10 false *1
*1 Cross Shaft
*2 Pitman Arm
*a Matchmark


Align the matchmarks on the pitman arm and cross shaft.


b.

Install the pitman arm to the cross shaft with the spring washer and nut.

Torque:
195 N*m (1988 kgf*cm, 144 ft.*lbf)


Hide 45460A 8.INSTALL TIE ROD ASSEMBLY

a.

Install the tie rod to the right and left knuckle arm, and then install the 2 castle nuts.

Torque:
90.7 N*m (925 kgf*cm, 67 ft.*lbf)


b.

Install 2 new cotter pins.


Hide 45450 9.INSTALL STEERING RELAY ROD ASSEMBLY

a.

Install the steering relay rod assembly to the pitman arm and knuckle arm, and then install the 2 castle nuts.

Torque:
90.7 N*m (925 kgf*cm, 67 ft.*lbf)


b.

Install the 2 new cotter pins.


c.

Tighten the 2 bolts and 2 nuts to tighten the 2 clamps.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)


Hide 45721 10.INSTALL STEERING DAMPER BRACKET

a.

Install the steering damper bracket with the 3 bolts.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


Hide 45700 11.INSTALL STEERING DAMPER ASSEMBLY

a.

Install the steering damper assembly to the steering relay rod end sub-assembly and steering damper bracket, and then install the 2 nuts.

Torque:
73.6 N*m (751 kgf*cm, 54 ft.*lbf)


Hide 12.INSTALL FRONT WHEELS

Hide 13.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT