Home › Steering › POWER ASSIST SYSTEMS › VANE PUMP (except 1GR-FE)
RM25T0E _55 Steering _029920 POWER ASSIST SYSTEMS _0137065 VANE PUMP(except 1GR-FE) A

POWER ASSIST SYSTEMS  VANE PUMP(except 1GR-FE)  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

When installing parts, coat the parts indicated by arrows with power steering fluid.

Click hereSteering>POWER ASSIST SYSTEMS>VANE PUMP (except 1GR-FE)>COMPONENTS


PROCEDURE

Hide 1.INSTALL VANE PUMP HOUSING OIL SEAL

a.

Coat a new lip of the vane pump housing oil seal with power steering fluid.


b.
C313991N01
0.979,1.125 0.469,0.51 0.469,0.51 1.104,0.896 true 0.188,0.375 0.646,0.573 0.458,0.198 10 false SST

Using SST and a press, press in the vane pump housing oil seal.

SST
09950-60010  (09951-00320)
09950-70010  (09951-07150)


Hide 2.INSTALL VANE PUMP SHAFT BEARING

a.
C162116

Using a brass bar and hammer, tap in a new vane pump shaft snap ring.

NOTICE:

Be careful not to damage the vane pump shaft.



b.
C162117

Using a press, press in the vane pump shaft into the vane pump shaft bearing.

NOTICE:

Be careful not to damage the vane pump shaft bearing.



Hide 3.INSTALL VANE PUMP SHAFT WITH VANE PUMP SHAFT BEARING

a.

Temporarily install the rear vane pump housing to the front vane pump housing.


b.
C313992N01
1,0.854 0.583,0.417 true 0.271,0.313 0.729,0.51 0.458,0.198 10 false SST

Using SST and a press, press in the vane pump shaft with vane pump shaft bearing into the front vane pump housing.

SST
09632-36010  


c.

Using a screwdriver, install a new vane pump housing snap ring into the front vane pump housing.


Hide 44316 4.INSTALL VANE PUMP GEAR

a.
C162119N01
0.979,0.875 0.625,0.583 true 0.333,0.479 0.729,0.688 0.396,0.208 10 false SST

Using SST and a press, press in the vane pump gear to the vane pump shaft.

SST
09950-60010  (09951-00420)


b.

Remove the rear vane pump housing from the front vane pump housing.


Hide 5.INSTALL VANE PUMP FRONT SIDE PLATE

a.
C162123

Coat a new O-ring with power steering fluid and install it into the front vane pump housing.


b.
C162156

Coat a new O-ring with power steering fluid and install it onto the vane pump front side plate.


c.
C161399C01
2.146,0.396 2.552,0.573 0.406,0.177 10 true *a
*a Align


Align the notch of the vane pump front side plate with the notch of the front vane pump housing, and install the vane pump front side plate.

NOTICE:

Make sure that the vane pump front side plate is installed facing in the correct direction.



Hide 6.INSTALL VANE PUMP CAM RING

a.
C161400C01
2.313,0.365 2.719,0.542 0.406,0.177 10 true *a
*a Align


Align the notch of the vane pump cam ring with the notch of the vane pump front side plate, and install the vane pump cam ring with the inscribed mark facing upward.

NOTICE:

Make sure that the vane pump cam ring is installed facing in the correct direction.



Hide 7.INSTALL VANE PUMP ROTOR AND VANE PUMP PLATE

a.

Install the vane pump rotor with the inscribed mark facing outward.


b.

Coat the 10 vane pump plates with power steering fluid.


c.
C161401C01
2.823,0.594 3.01,1.573 true 2.969,1.615 3.281,1.885 0.313,0.271 10 false *a
*a Round End


Install the 10 vane pump plates with the round end facing outward.

NOTICE:

Make sure that the 10 vane pump plates are installed facing in the correct direction.



Hide 8.INSTALL REAR VANE PUMP HOUSING

a.

Coat a new O-ring with power steering fluid and install it onto the rear vane pump housing.

NOTICE:

Securely insert the O-ring into the groove of the vane pump rear housing.



b.
C162122C01
0.917,0.896 0.458,1.083 true 3.063,0.302 2.396,0.635 true 2.385,1.469 1.49,1.177 true 0.25,1 0.781,1.26 0.531,0.26 10 false *a 3.104,0.208 3.385,0.448 0.281,0.24 10 false *b 2.458,1.385 2.74,1.625 0.281,0.24 10 false *c
*a Straight Pin
*b Match
*c Apply power steering fluid


Align the straight pin of the rear vane pump housing with the notches of the vane pump cam ring, vane pump front side plate and front vane pump housing.

NOTICE:

Check that the O-ring has not come out of the groove and install the vane pump rear housing.


HINT:

Apply power steering fluid to the end of the vane pump shaft with pulley.



c.
C162098

Install the rear vane pump housing with the 4 bolts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 9.INSTALL FLOW CONTROL VALVE

a.

Coat the flow control valve with power steering fluid.


b.
C162100

Install the flow control valve compression spring and flow control valve to the front vane pump housing.


c.

Coat a new O-ring with power steering fluid and install it onto the pressure port union.


d.

Install the pressure port union to the front vane pump housing.

Torque:
69 N*m (704 kgf*cm, 51 ft.*lbf)


Hide 44337 10.INSTALL POWER STEERING SUCTION PORT UNION

a.

Coat a new O-ring with power steering fluid and install it to the power steering suction port union.


b.

Install the power steering suction port union to the vane pump assembly with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 11.INSPECT TOTAL PRELOAD

a.

Check that the vane pump rotates smoothly without abnormal noise.


b.
C308172C01
0.958,0.677 1.417,0.927 true 0.802,0.583 1.052,0.74 0.25,0.156 8 false *a
*a Service Bolt


Temporarily install the service bolt.

Recommended service bolt:
Thread diameter:

10 mm (0.394 in.)

Thread pitch:

1.25 mm (0.0493 in.)

Bolt length:

50 mm (1.97 in.)



c.

Using a torque wrench, measure the pump rotating torque.

Standard rotating torque:

0.27 N*m (2.8 kgf*cm, 2.4 in.*lbf) or less


If the rotating torque is not as specified, check the vane pump housing oil seal.