Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL LOCK ACTUATOR(w/ Differential Lock)
RM25T0E _52 Drivetrain _029907 AXLE AND DIFFERENTIAL _0136712 REAR DIFFERENTIAL LOCK ACTUATOR(w/ Differential Lock) G

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL LOCK ACTUATOR(w/ Differential Lock)  INSPECTION  


PROCEDURE

Hide 41450 1.INSPECT DIFFERENTIAL LOCK SHIFT ACTUATOR

a.

Check the free to lock switch.

i.

Connect lines via a relay as shown in the illustration, and check that the actuator fork moves from the free to lock position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the HTR relay.


C313149C01
5.406,2.927 5.646,2.927 5.646,2.927 5.927,3.198 false 5.115,3.281 5.354,3.281 5.354,3.281 5.635,3.552 false 5.552,4.365 5.792,4.365 5.792,4.365 6.01,4 false 6.698,3.01 6.438,3.01 6.438,3.01 6.104,3.583 false 6.438,3.604 6.729,3.604 false 1.896,4.01 1.635,4.01 1.635,4.01 1.458,4.365 false 0.938,4.021 1.031,4.021 1.031,4.021 1.104,4.354 false 0.896,5.042 0.99,5.042 0.99,5.042 1.156,4.74 false 1.396,4.74 1.396,5.167 false 2.031,4.99 1.771,4.99 1.771,4.99 1.646,4.729 false 0.292,0.104 0.604,0.302 0.313,0.198 10 false *a 2.542,2.146 2.854,2.344 0.313,0.198 10 false *b 5.885,2.49 6.198,2.688 0.313,0.198 10 false *c 5.271,2.833 5.583,3.031 0.313,0.198 10 false 1 5,3.198 5.313,3.396 0.313,0.198 10 false 3 5.438,4.281 5.75,4.479 0.313,0.198 10 false 2 6.781,2.917 7.094,3.115 0.313,0.198 10 false 4 6.792,3.51 7.104,3.708 0.313,0.198 10 false 5 2,3.906 2.313,4.104 0.313,0.198 10 false M2 0.708,3.938 1.021,4.135 0.313,0.198 10 false M1 0.521,4.958 0.979,5.177 0.458,0.219 10 false RLY1 1.229,5.208 1.688,5.427 0.458,0.219 10 false RLY2 2.094,4.896 2.49,5.104 0.396,0.208 10 false GND
*a Component without harness connected
(Differential Lock Shift Actuator)
*b Free → Lock
*c HTR Relay - -



ii.

After the free to lock switch is complete, check the limit switch of the shift actuator.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (RLY2) - 4 (GND) After free to lock switch is complete Below 12.5 Ω
6 (RLY1) - 4 (GND) After free to lock switch is complete 500 kΩ or higher


If the result is not as specified, replace the differential lock shift actuator assembly.



b.

Check the lock to free switch.

i.

Connect lines via a relay as shown in the illustration, and check that the actuator fork moves from the lock to free position.

NOTICE:
·

Make sure to perform this inspection with the actuator removed from the vehicle. If this inspection is performed with the actuator installed to the vehicle, the actuator will be damaged.

·

When inspecting the actuator, make sure to operate it with the lines connected via a relay. If the lines are not connected via a relay and battery voltage is directly applied to the actuator, the actuator will be damaged.



HINT:

When performing the operation described above, use the HTR relay.


C313150C01
5.531,2.906 5.729,2.906 5.729,2.906 6.063,3.146 false 6.542,3.531 6.833,3.531 false 5.24,3.26 5.438,3.26 5.438,3.26 5.771,3.5 false 5.531,4.208 5.729,4.208 5.729,4.208 6.073,3.927 false 6.698,2.948 6.5,2.948 6.5,2.948 6.208,3.469 false 0.938,3.958 1.135,3.958 1.135,3.958 1.198,4.292 false 0.948,4.885 1.115,4.885 1.115,4.885 1.25,4.646 false 1.938,3.948 1.76,3.948 1.76,3.948 1.563,4.292 false 2.115,4.833 1.938,4.833 1.938,4.833 1.771,4.656 false 2.115,5.167 1.938,5.167 1.938,5.167 1.563,4.625 false 0.292,0.083 0.604,0.281 0.313,0.198 10 false *a 2.469,2.073 2.781,2.271 0.313,0.198 10 false *b 6,2.396 6.313,2.594 0.313,0.198 10 false *c 5.396,2.823 5.708,3.021 0.313,0.198 10 false 1 5.115,3.177 5.427,3.375 0.313,0.198 10 false 3 5.406,4.125 5.719,4.323 0.313,0.198 10 false 2 6.781,2.854 7.094,3.052 0.313,0.198 10 false 4 6.875,3.458 7.156,3.656 0.281,0.198 10 false 5 0.719,3.875 1.031,4.073 0.313,0.198 10 false M1 0.563,4.813 0.99,5.01 0.427,0.198 10 false RLY1 2.01,3.854 2.323,4.052 0.313,0.198 10 false M2 2.208,4.76 2.698,4.958 0.49,0.198 10 false GND 2.177,5.083 2.604,5.281 0.427,0.198 10 false RLY2
*a Component without harness connected
(Differential Lock Shift Actuator)
*b Lock → Free
*c HTR Relay - -



ii.

After the free to lock switch is complete, check the limit switch of the shift actuator.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (RLY2) - 4 (GND) After free to lock switch is complete 500 kΩ or higher
6 (RLY1) - 4 (GND) After free to lock switch is complete Below 12.5 Ω


If the result is not as specified, replace the differential lock shift actuator assembly.