Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM
RM25T0E _56 Audio / Visual / Telematics _029922 AUDIO / VIDEO _0137647 AUDIO AND VISUAL SYSTEM J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM  Radio Receiver Power Source Circuit  


DESCRIPTION

This circuit provides power to the radio receiver assembly.

WIRING DIAGRAM

C240172E42
5.073,3.104 6.719,3.344 1.646,0.24 10 false Radio Receiver Assembly 5.51,0.844 5.646,1.01 0.135,0.167 10 false B 5.5,2.302 5.885,2.469 0.385,0.167 10 false E 5.5,1.583 5.854,1.75 0.354,0.167 10 false ACC 5.313,0.698 5.448,0.865 0.135,0.167 10 false 4 5.313,2.167 5.448,2.333 0.135,0.167 10 false 7 5.313,1.427 5.427,1.594 0.115,0.167 10 false 3 2.802,1.406 3.927,1.604 1.125,0.198 10 false ACC 2.75,0.688 3.271,0.865 0.521,0.177 10 false RADIO 0.771,0.813 1.604,0.99 0.833,0.177 10 false from Battery 0.313,1.563 1.667,1.875 1.354,0.313 10 false from Ignition Switch 5.094,2.917 5.49,3.104 0.396,0.188 10 false L2

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY- BATTERY AND BODY GROUND)
a.
E141019C16
1.5,0.5 1.906,0.76 0.406,0.26 1.313,1.927 1.51,1.927 1.51,1.927 1.604,1.552 true 2.344,0.938 2.156,0.938 2.156,0.938 1.938,1.219 true 2.458,1.604 2.271,1.604 2.271,1.604 2.115,1.344 true 2.406,0.833 3.021,1.031 0.615,0.198 10 false ACC 0.125,0.073 0.438,0.271 0.313,0.198 10 false *a 1.198,1.802 1.354,2 0.156,0.198 10 false E 1.625,0.552 2.083,0.75 0.458,0.198 10 false L2 2.51,1.5 3.125,1.698 0.615,0.198 10 false B
*a Front view of wire harness connector
(to Radio Receiver Assembly)


Disconnect the radio receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L2-4 (B) - Body ground Always 11 to 14 V
L2-3 (ACC) - Body ground Ignition switch ACC 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-7 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR