Wear protective gloves. Sharp areas on the seat frame may injure your hands.
72694 1.REMOVE REAR SEAT CUSHION LOCK COVER
Use the same procedure for the other side.
Remove the 2 screws and the rear seat cushion lock cover.
72660A 2.REMOVE REAR SEAT CUSHION SUPPORT ASSEMBLY
Use the same procedure for the other side.
Remove the 2 bolts.
Detach the clamp and disconnect the No. 2 fold seat lock control cable assembly as shown in the illustration and remove the rear seat cushion support assembly.
73350 3.REMOVE REAR CENTER SEAT LAP TYPE BELT ASSEMBLY
73390 4.REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH
73380 5.REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH
6.REMOVE BENCH TYPE REAR SEATBACK ASSEMBLY
Remove the 2 bolts and bench type rear seatback assembly.
78950 7.REMOVE NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY
| *1 | Fastening Tape |
Detach the fastening tape and open the bench type rear seatback cover.
Remove the 8 hog rings.
Remove the bolt and No. 1 fold seat stopper band assembly.
71955A 8.REMOVE REAR SEAT HEADREST SUPPORT
Remove the 2 hog rings.
Detach the 8 claws and remove the 4 rear seat headrest supports.
71931A 9.REMOVE REAR SEAT HEADREST SUPPORT
Remove the 12 hog rings.
Detach the 8 claws and remove the 4 rear seat headrest supports.
71077B 10.REMOVE BENCH TYPE REAR SEATBACK COVER
Remove the bench type rear seatback cover from the rear seatback pad.
71651B 11.REMOVE BENCH TYPE REAR SEATBACK PAD
As the bench type rear seatback pad is affixed to the rear seatback frame sub-assembly, do not remove the bench type rear seatback pad from the rear seatback frame sub-assembly unless it is necessary to replace the bench type rear seatback pad. If the bench type rear seatback pad is removed from the rear seatback frame sub-assembly, make sure to replace the bench type rear seatback pad.
Perform the following only when replacing the bench type rear seatback pad or rear seatback frame sub-assembly.
| *a | Adhesive Area |
Detach the part of the bench type rear seatback pad attached with adhesive shown in the illustration, and remove the bench type rear seatback pad.
71663 12.REMOVE REAR LOWER SEATBACK PAD
As the rear lower seatback pad is affixed to the rear seatback frame sub-assembly, do not remove the rear lower seatback pad from the rear seatback frame sub-assembly unless it is necessary to replace the rear lower seatback pad. If the rear lower seatback pad is removed from the rear seatback frame sub-assembly, make sure to replace the rear lower seatback pad.
Perform the following only when replacing the rear lower seatback pad or rear seatback frame sub-assembly.
| *a | Adhesive Area |
Detach the part of the rear lower seatback pad attached with adhesive shown in the illustration, and remove the rear lower seatback pad.
71651 13.REMOVE REAR NO. 1 SEATBACK PAD
As the rear No. 1 seatback pad is affixed to the rear seatback frame sub-assembly, do not remove the rear No. 1 seatback pad from the rear seatback frame sub-assembly unless it is necessary to replace the rear No. 1 seatback pad. If the rear No. 1 seatback pad is removed from the rear seatback frame sub-assembly, make sure to replace the rear No. 1 seatback pad.
Perform the following only when replacing the rear No. 1 seatback pad or rear seatback frame sub-assembly.
| *a | Adhesive Area |
Detach the part of the rear No. 1 seatback pad attached with adhesive shown in the illustration, and remove the rear No. 1 seatback pad.
71671 14.REMOVE REAR SEATBACK SILENCER PAD A
As the rear seatback silencer pad A is affixed to the rear seatback frame sub-assembly, do not remove the rear seatback silencer pad A from the rear seatback frame sub-assembly unless it is necessary to replace the rear seatback silencer pad A. If the rear seatback silencer pad A is removed from the rear seatback frame sub-assembly, make sure to replace the rear seatback silencer pad A.
Perform the following only when replacing the rear seatback silencer pad A or rear seatback frame sub-assembly.
| *a | Adhesive Area |
Detach the part of the rear seatback silencer pad A attached with adhesive shown in the illustration, and remove the rear seatback silencer pad A.
72604 15.REMOVE REAR SEATBACK LOCK SUB-ASSEMBLY LH
Remove the bush from the rear seatback lock sub-assembly LH.
Remove the 2 bolts.
Remove the 2 screws and remove the rear seatback lock cover.
Using a screwdriver, unstake the stake part of the rear seatback lock sub-assembly LH.
Tape the screwdriver tip before use.
| *1 | Stake Part | *2 | Protective Tape |
Remove the screw and disconnect the No. 1 seat lock control cable assembly and remove the rear seatback lock sub-assembly LH.
72603 16.REMOVE REAR SEATBACK LOCK SUB-ASSEMBLY RH
Use the same procedure for the LH side.
78960 17.REMOVE NO. 2 FOLD SEAT STOPPER BAND ASSEMBLY
Use the same procedure for the other side.
Remove the 2 bolts and No. 2 fold seat stopper band assembly
79929 18.REMOVE FOLD SEAT LEG STOPPER FRAME
Using a screwdriver, remove the 2 spring nuts.
Remove the fold seat leg stopper frame and 4 washers.
71382A 19.REMOVE REAR SEAT CUSHION SET BRACKET LH
Remove the bolt and nut, and rear seat cushion set bracket LH.
71381A 20.REMOVE REAR SEAT CUSHION SET BRACKET RH
Use the same procedure for the LH side.
71033 21.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY
Detach the 2 clamps and disconnect the No. 2 fold seat lock control cable assembly.
Using a screwdriver, remove the 3 E-rings and 3 rear seat cushion leg pins and rear seat cushion leg sub-assembly.
78910 22.REMOVE NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY
Detach the 5 pieces of fastening tape and open the bench type rear seat cushion cover.
Remove the clamp A.
| *1 | Clamp A | *2 | Clamp B |
Detach the 3 clamp B and disconnect the 2 fold seat lock control cable assemblies.
Remove the 2 bolts and 2 fold seat lock control cable assemblies together with the rear seat lock release strap assembly.
Loosen the nut and disconnect the No. 1 fold seat lock control cable assembly as shown in the illustration.
78920 23.REMOVE NO. 2 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY
Loosen the nut and disconnect the No. 2 fold seat lock control cable assembly as shown in the illustration.
71075B 24.REMOVE BENCH TYPE REAR SEAT CUSHION COVER
Remove the 22 hog rings.
Remove the 6 hog rings and bench type rear seat cushion cover.
71611 25.REMOVE REAR SEAT CUSHION PAD
Remove the rear seat cushion pad from the rear seat cushion frame sub-assembly.
26.REMOVE CLIP
Detach the 3 claws and remove the 3 clips from the rear seat cushion frame sub-assembly.