1.INSPECT 3RD GEAR THRUST CLEARANCE
2.INSPECT 5TH GEAR THRUST CLEARANCE
3.INSPECT 2ND GEAR THRUST CLEARANCE
4.INSPECT 1ST GEAR THRUST CLEARANCE
5.INSPECT 3RD GEAR RADIAL CLEARANCE
6.INSPECT 5TH GEAR RADIAL CLEARANCE
7.INSPECT 2ND GEAR RADIAL CLEARANCE
8.INSPECT 1ST GEAR RADIAL CLEARANCE
33321B 9.REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING
| *a | Protective Tape |
Using 2 screwdrivers and a hammer, tap out the output shaft bearing shaft snap ring.
Do not damage the output shaft.
Use a piece of cloth to prevent the snap ring from flying off.
Tape the screwdriver tip before use.
33335 10.REMOVE 1ST GEAR
Shift the No. 1 transmission hub sleeve to the 2nd gear.
Using SST and a press, remove the rear output shaft bearing and 1st gear.
Do not drop the output shaft.
33335C 11.REMOVE 1ST GEAR NEEDLE ROLLER BEARING
Remove the 1st gear needle roller bearing from the output shaft.
33367 12.REMOVE NO. 1 SYNCHRONIZER RING
Remove the No. 1 synchronizer ring set from the No. 1 transmission clutch hub.
33367 13.INSPECT NO. 1 SYNCHRONIZER RING
33335 14.INSPECT 1ST GEAR
33361B 15.REMOVE NO. 1 CLUTCH HUB SHAFT SNAP RING
| *a | Protective Tape |
Using 2 screwdrivers and a hammer, tap out the No. 1 clutch hub shaft snap ring.
Do not damage the output shaft.
Use a piece of cloth to prevent the snap ring from flying off.
Tape the screwdriver tip before use.
33332 16.REMOVE 2ND GEAR
Using SST and a press, remove the 2nd gear and No. 1 transmission clutch hub.
Do not drop the output shaft.
33332B 17.REMOVE 2ND GEAR NEEDLE ROLLER BEARING
Remove the 2nd gear needle roller bearing from the output shaft.
33363 18.REMOVE NO. 1 TRANSMISSION HUB SLEEVE
Remove the No. 1 transmission clutch hub from the output shaft.
| *1 | No. 1 Transmission Hub Sleeve |
| *2 | No. 1 Transmission Clutch Hub |
| *3 | Shifting Key |
| *4 | Spring |
Using a screwdriver, remove the 2 springs, 3 shifting keys and No. 1 transmission hub sleeve from the No. 1 transmission clutch hub.
Do not damage the No. 1 transmission hub sleeve and No. 1 transmission clutch hub.
Use a piece of cloth to prevent the snap ring from flying off.
33363 19.INSPECT NO. 1 TRANSMISSION HUB SLEEVE
33038E 20.REMOVE NO. 2 SYNCHRONIZER RING SET
Remove the No. 2 synchronizer ring from the 2nd gear.
33038E 21.INSPECT NO. 2 SYNCHRONIZER RING SET
33332 22.INSPECT 2ND GEAR
33362A 23.REMOVE NO. 2 CLUTCH HUB SETTING SHAFT SNAP RING
| *a | Protective Tape |
Using 2 screwdrivers and a hammer, tap out the No. 2 clutch hub setting shaft snap ring.
Do not damage the output shaft.
Use a piece of cloth to prevent the snap ring from flying off.
Tape the screwdriver tip before use.
33333 24.REMOVE 3RD GEAR
Shift the No. 3 transmission hub sleeve to the 5th gear.
Using SST and a press, remove the 3rd gear, No. 3 synchronizer ring set and No. 2 transmission clutch hub.
Do not drop the output shaft.
33333A 25.REMOVE 3RD GEAR NEEDLE ROLLER BEARING
Remove the 3rd gear needle roller bearing from the output shaft.
36235B 26.REMOVE NO. 2 TRANSMISSION HUB SLEEVE
Remove the No. 2 transmission clutch hub from the 3rd gear.
| *1 | No. 2 Transmission Hub Sleeve |
| *2 | No. 2 Transmission Clutch Hub |
| *3 | Shifting Key |
| *4 | Spring |
Using a screwdriver, remove the 2 springs, 3 shifting keys and No. 2 transmission hub sleeve from the No. 2 transmission clutch hub.
Do not damage the No. 1 transmission hub sleeve and No. 1 transmission clutch hub.
Use a piece of cloth to prevent the snap ring from flying off.
36235B 27.INSPECT NO. 2 TRANSMISSION HUB SLEEVE
33039 28.REMOVE NO. 3 SYNCHRONIZER RING SET
Remove the No. 3 synchronizer ring set from the 3rd gear.
33039 29.INSPECT NO. 3 SYNCHRONIZER RING SET
33333 30.INSPECT 3RD GEAR
33393A 31.REMOVE TRANSMISSION CLUTCH HUB NO.3 SHAFT SNAP RING
| *a | Protective Tape |
Using 2 screwdrivers and a hammer, tap out the snap ring.
Do not damage the output shaft.
Use a piece of cloth to prevent the snap ring from flying off.
Tape the screwdriver tip before use.
33336 32.REMOVE 5TH GEAR
Using SST and a press, remove the 5th gear, No. 3 synchronizer ring and No. 3 transmission clutch hub.
Do not drop the output shaft.
33428B 33.REMOVE COUNTER 5TH GEAR BEARING
Remove the 5th counter gear bearing from the output shaft.
33395 34.REMOVE NO. 3 TRANSMISSION HUB SLEEVE
Remove the No. 3 transmission clutch hub from the 3rd gear.
| *1 | No. 3 Transmission Hub Sleeve |
| *2 | No. 3 Transmission Clutch Hub |
| *3 | Shifting Key |
| *4 | Spring |
Using a screwdriver, remove the 2 springs, 3 shifting keys and No. 3 transmission hub sleeve from the No. 3 transmission clutch hub.
Do not damage the No. 1 transmission hub sleeve and No. 1 transmission clutch hub.
Use a piece of cloth to prevent the snap ring from flying off.
33395 35.INSPECT NO. 3 TRANSMISSION HUB SLEEVE
33369 36.REMOVE NO. 3 SYNCHRONIZER RING
Remove the No. 3 synchronizer ring from the 5th gear.
33369 37.INSPECT NO. 3 SYNCHRONIZER RING
33336 38.INSPECT 5TH GEAR