Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › QUARTER PANEL WHEEL OPENING MOULDING(for Model Code #J76 Series)
RM25T0E _59 Vehicle Exterior _029942 EXTERIOR PANELS / TRIM _0137752 QUARTER PANEL WHEEL OPENING MOULDING(for Model Code #J76 Series) A

EXTERIOR PANELS / TRIM  QUARTER PANEL WHEEL OPENING MOULDING(for Model Code #J76 Series)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the LH and RH sides.

·

The procedures listed below are for the LH side.



PROCEDURE

Hide 76608 1.REMOVE REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY LH

Hide 61064A 2.REMOVE REAR NO. 2 WHEEL OPENING EXTENSION SUB-ASSEMBLY LH

a.
B388436

Remove the 3 bolts and rear No. 2 wheel opening extension sub-assembly LH.


Hide 61785C 3.REMOVE REAR NO. 2 WHEEL OPENING EXTENSION PAD

a.
B388374

Remove the rear No. 2 wheel opening extension pad.


Hide 61785C 4.REMOVE REAR NO. 3 WHEEL OPENING EXTENSION PAD

a.
B388437

Remove the rear No. 3 wheel opening extension pad.


Hide 61695D 5.REMOVE REAR NO. 3 WHEEL OPENING BRACKET REAR LH

B167652N02
1.438,1.594 1.667,1.875 0.229,0.281 10 false A

a.

Remove the 2 rivets and rear No. 3 wheel opening bracket rear LH.

i.

Put a 4 mm (0.157 in.) drill bit into a drill.


ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill, as shown in the illustration.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.


Standard:
Area Specified Condition
A 5 mm (0.197 in.)



iii.

Lightly press the drill bit against the rivets, drill off the flanges of the rivets, and remove the 2 rivets and rear No. 3 wheel opening bracket rear LH.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivets with the drill, as this may cause damage to the installation holes of the rivets or the drill bit.



CAUTION:

Be careful of the drilled rivets, as they may become hot.



iv.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.



Hide 53872C 6.REMOVE REAR NO. 8 WHEEL OPENING BRACKET REAR LH

B168835N02
1.74,1.177 2.01,1.469 0.271,0.292 10 false A

a.

Remove the 2 rivets and rear No. 8 wheel opening bracket rear LH.

i.

Put a 4 mm (0.157 in.) drill bit into a drill.


ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill, as shown in the illustration.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.


Standard:
Area Specified Condition
A 5 mm (0.197 in.)



iii.

Lightly press the drill bit against the rivets, drill off the flanges of the rivets, and remove the 2 rivets and rear No. 8 wheel opening bracket rear LH.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivets with the drill, as this may cause damage to the installation holes of the rivets or the drill bit.



CAUTION:

Be careful of the drilled rivets, as they may become hot.



iv.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.



Hide 61693D 7.REMOVE REAR NO. 1 WHEEL OPENING BRACKET REAR LH

B168836N02
2.083,1.604 2.333,1.875 0.25,0.271 10 false A

a.

Remove the 4 rivets and 2 rear No. 1 wheel opening bracket rear LH.

i.

Put a 4 mm (0.157 in.) drill bit into a drill.


ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill, as shown in the illustration.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.


Standard:
Area Specified Condition
A 5 mm (0.197 in.)



iii.

Lightly press the drill bit against the rivets, drill off the flanges of the rivets, and remove the 4 rivets and rear No. 1 wheel opening bracket rear LH.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivets with the drill, as this may cause damage to the installation holes of the rivets or the drill bit.



CAUTION:

Be careful of the drilled rivets, as they may become hot.



iv.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.



Hide 61062C 8.REMOVE REAR NO. 1 WHEEL OPENING EXTENSION SUB-ASSEMBLY LH

a.
B167649

Remove the 2 nuts, bolt and rear No. 1 wheel opening extension sub-assembly LH.


Hide 61783D 9.REMOVE REAR NO. 1 WHEEL OPENING EXTENSION PAD

a.
B388373

Remove the rear No. 1 wheel opening extension pad.


Hide 61696F 10.REMOVE REAR NO. 2 WHEEL OPENING BRACKET FRONT LH

B167651N02
1.458,1.438 1.688,1.677 0.229,0.24 10 false A

a.

Remove the 2 rivets and rear No. 2 wheel opening bracket front LH.

i.

Put a 4 mm (0.157 in.) drill bit into a drill.


ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill, as shown in the illustration.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.


Standard:
Area Specified Condition
A 5 mm (0.197 in.)



iii.

Lightly press the drill bit against the rivets, drill off the flanges of the rivets, and remove the 2 rivets and rear No. 2 wheel opening bracket front LH.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivets with the drill, as this may cause damage to the installation holes of the rivets or the drill bit.



CAUTION:

Be careful of the drilled rivets, as they may become hot.



iv.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.



Hide 61695D 11.REMOVE REAR NO. 3 WHEEL OPENING BRACKET FRONT LH

B168252N02
1.844,0.625 2.063,0.875 0.219,0.25 10 false A

a.

Remove the 2 rivets and rear No. 3 wheel opening bracket front LH.

i.

Put a 4 mm (0.157 in.) drill bit into a drill.


ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill, as shown in the illustration.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.


Standard:
Area Specified Condition
A 5 mm (0.197 in.)



iii.

Lightly press the drill bit against the rivets, drill off the flanges of the rivets, and remove the 2 rivets and rear No. 3 wheel opening bracket front LH.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivets with the drill, as this may cause damage to the installation holes of the rivets or the drill bit.



CAUTION:

Be careful of the drilled rivets, as they may become hot.



iv.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.



Hide 61698F 12.REMOVE REAR NO. 4 WHEEL OPENING BRACKET FRONT LH

B168253N01
2.323,0.313 2.573,0.552 0.25,0.24 10 false A

a.

Remove the 2 rivets and rear No. 4 wheel opening bracket front LH.

i.

Put a 4 mm (0.157 in.) drill bit into a drill.


ii.

Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill, as shown in the illustration.

HINT:

Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.


Standard:
Area Specified Condition
A 5 mm (0.197 in.)



iii.

Lightly press the drill bit against the rivets, drill off the flanges of the rivets, and remove the 2 rivets and rear No. 4 wheel opening bracket front LH.

NOTICE:
·

Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

·

Do not pry the rivets with the drill, as this may cause damage to the installation holes of the rivets or the drill bit.



CAUTION:

Be careful of the drilled rivets, as they may become hot.



iv.

Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.