Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › GRAPHIC DECAL
RM25T0E _59 Vehicle Exterior _029942 EXTERIOR PANELS / TRIM _0137753 GRAPHIC DECAL A

EXTERIOR PANELS / TRIM  GRAPHIC DECAL  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

When installing the stripe tape, heat the vehicle body and stripe tape using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)
Stripe Tape 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the vehicle body or stripe tape excessively.


PROCEDURE

Hide 1.REPAIR INSTRUCTION

a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Wipe off any tape adhesive residue with cleaner.



b.

Installation temperature.

i.

When the ambient temperature is below 15°C (59°F), perform the installation procedure after warming the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) using a heat light. When the ambient temperature is above 35°C (95°F), cool the vehicle body surface (installation surface of the door frame) and tape to between 20 and 30°C (68 and 86°F) prior to installation.

HINT:
·

The most appropriate temperature for installing the tape is 25°C (77°F).

·

When the temperature is low, the tape turns stiff and falls off easily. When the temperature is high, the tape loses elasticity.





c.

Before installation.

i.

Make sure any dirt on and around the vehicle body surface where the tape will be installed (installation surface of the door frame) is removed, and that the surface is smooth. If the surface is rough or dirt remains when pressing the tape onto the surface, air will be trapped under the tape and result in a poor appearance.

HINT:

Spray water on the shop floor to settle any dust.




d.

Key points for handling the tape.

i.

The tape bends and rolls up easily. Store the tape between flat pieces of cardboard or other similar objects and keep it dry and level.

NOTICE:

Do not bend the tape or leave it in places with a high temperature.




e.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for a flat surface).

NOTICE:
·

Position the tape with a high level of accuracy to achieve a neat finish and to avoid peeling.

·

The tape cannot be reused because it deforms and will not fit after removal.



i.

To avoid air bubbles, slightly raise the part of the tape that is going to be applied so that its adhesive surface does not touch the vehicle body while applying the tape. Tilt the squeegee 40 to 50° (for pressing forward) or 30 to 45° (for pulling) from the vehicle body surface and press with a force of 20 to 30 N (2 to 3 kgf) while moving the squeegee at a constant slow speed of 3 to 7 cm (1.2 to 2.8 in.) per second.

NOTICE:

Be sure to observe the specified pressing speed, force and angle of the squeegee to avoid wrinkles and air bubbles.


HINT:
·

Either angle of the squeegee (for pressing forward or for pulling) is acceptable.

·

Be sure to apply the tape while removing the release paper 10 to 20 mm (0.393 to 0.787 in.) from the edge of the squeegee.



B233855C15
0.083,0.073 3.875,1.563 3.792,1.49 0.688,0.625 0.833,0.479 0.833,0.479 1,0.479 false 2.177,0.698 2.292,0.323 2.292,0.323 2.542,0.323 false 2.156,1.24 2.813,1.24 false 2.146,1.99 2.146,1.823 2.146,1.823 2.604,1.823 false 2.094,3.427 2.646,3.427 false 4.594,2.625 4.99,2.625 false 4.875,3.052 5.302,3.052 false 5.729,2.604 5.969,2.948 5.969,2.948 6.083,2.948 false 5.677,3.271 6.073,3.271 false 1.042,2.844 1.802,2.844 1.802,2.844 2.042,2.292 false 1.125,3.25 1.646,3.25 false 0.865,2.344 1.865,2.542 1,0.198 10 false 3 to 7 cm/sec. 3.875,2.229 4.948,2.448 1.073,0.219 10 false 3 to 7 cm/sec. 2.677,1.75 3.25,1.927 0.573,0.177 10 false 40 to 50° 6.135,2.885 6.708,3.063 0.573,0.177 10 false 30 to 45° 2.844,2.563 3.635,2.74 0.792,0.177 10 false 10 to 20 mm 6.125,2.521 6.917,2.698 0.792,0.177 10 false 10 to 20 mm 0.125,0.115 0.313,0.271 0.188,0.156 10 false *a 2.552,0.25 2.74,0.417 0.188,0.167 10 false *b 2.833,1.177 3.01,1.323 0.177,0.146 10 false *c 1.021,0.396 1.188,0.542 0.167,0.146 10 false *1 0.885,2.771 1.052,2.917 0.167,0.146 10 false *1 0.083,1.594 0.302,1.76 0.219,0.167 10 false *A 0.958,3.177 1.125,3.344 0.167,0.167 10 false *2 4.438,2.573 4.604,2.719 0.167,0.146 10 false *1 4.708,2.979 4.875,3.146 0.167,0.167 10 false *2 2.667,3.354 2.865,3.521 0.198,0.167 10 false *3 3.656,1.615 3.854,1.781 0.198,0.167 10 false *B 6.104,3.198 6.281,3.365 0.177,0.167 10 false *3
*A Pressing *B Pulling
*1 Squeegee *2 Black Out Tape
*3 Release Paper - -
*a Sectional View *b Non-padded Side
*c Padded Side - -




f.
B233856C12
0.972,1.789 1.087,1.789 1.087,1.789 1.2,1.697 false 0.736,1.699 0.93,1.859 0.193,0.161 10 *1 2.335,0.435 2.514,0.615 0.179,0.179 10 *a 1.63,0.332 1.823,0.507 0.193,0.175 10 *b 0.908,0.424 1.116,0.617 0.207,0.193 10 *c
*1 Squeegee
*a First
*b Second
*c Third


Key points for the installation of the tape (how to use a squeegee and the installation procedure for hemming surfaces).

i.

If it is difficult to press the tape, press it in several steps as shown in the illustration. Use your fingers or the padded surface of a squeegee to slowly apply the tape to the hem of the vehicle, especially for a small hem.

HINT:

When applying tape to the backside of a hem, remove the release paper and use your fingers or the padded surface of a squeegee.




g.

Key points for the installation of the tape (how to use a squeegee and the installation procedure for the corners).

i.

Remove the release paper and apply the tape carefully with your fingers.


ii.

Before applying the tape to each corner, heat the tape using a heat light and gradually apply it to avoid wrinkles on the tape and achieve a neat finish.



h.

Check after installation.

i.

After completing the application, check if the tape is applied neatly. If the tape is not applied neatly, apply new tape.

NOTICE:

Do not reuse the tape.




Hide 75982B 2.INSTALL FENDER STRIPE LH

a.

Align the top of the application sheet of new stripe tape with the fender relief and the perforation with the front fender end line as shown in the illustration, and then apply the stripe tape.


b.

Remove the application sheet from the stripe tape.

HINT:

If the vehicle has an over fender, cut off any excess areas from perforation B and apply.


B333157C01
1.208,0.177 1.615,0.177 1.615,0.177 1.865,1.052 true 4.76,0.177 5.167,0.177 5.167,0.177 5.354,1.063 true 6.417,1.323 6.74,1.323 true 2.948,1.313 3.313,1.313 true 3,1.708 3.281,1.708 false 6.427,1.75 6.729,1.75 false 5.917,1.469 5.427,2.021 5.427,2.021 5.219,2.021 true 2.49,1.469 2.01,2.042 2.01,2.042 1.802,2.042 true 5.906,1.135 5.906,0.177 5.906,0.177 6.177,0.177 true 0.198,0.115 0.448,0.344 0.25,0.229 10 false *A 3.802,0.125 4.052,0.354 0.25,0.229 10 false *B 1.031,0.073 1.271,0.323 0.24,0.25 10 false *a 4.583,0.083 4.823,0.333 0.24,0.25 10 false *a 6.208,0.083 6.448,0.333 0.24,0.25 10 false *e 6.75,1.24 6.99,1.49 0.24,0.25 10 false *b 3.313,1.229 3.552,1.479 0.24,0.25 10 false *b 3.292,1.615 3.531,1.865 0.24,0.25 10 false *c 6.74,1.656 6.979,1.906 0.24,0.25 10 false *c 5.073,1.938 5.344,2.208 0.271,0.271 10 false *d 1.635,1.938 1.906,2.208 0.271,0.271 10 false *d
*A w/o Side Turn Signal Light *B w/ Side Turn Signal Light
*a Fender Relief *b Perforation A
*c Front Fender End Line *d Perforation B
*e Side Turn Signal Light Exterior - -



Hide 75981B 3.INSTALL FENDER STRIPE RH

HINT:

Use the same procedure described for the LH side.


Hide 75986 4.INSTALL FRONT DOOR STRIPE LH

a.

Align the top of the application sheet of new stripe tape with the front door relief and the perforations with the front door end lines as shown in the illustration, and then apply the stripe tape.


b.

Remove the application sheet from the stripe tape.

B324843C01
0.163,0 0.430,0.295 0.267,0.295 10 *A 3.861,0 4.128,0.295 0.267,0.295 10 *B 2.18,0.214 2.447,0.454 0.267,0.239 10 *a 0.142,1.44 0.409,1.679 0.267,0.239 10 *b 0.904,1.981 1.171,2.221 0.267,0.239 10 *c 3.154,1.44 3.421,1.679 0.267,0.239 10 *b 3.911,1.451 4.178,1.690 0.267,0.239 10 *b 6.748,1.451 7.015,1.690 0.267,0.239 10 *b 1.667,1.354 1.667,0.289 1.667,0.289 2.157,0.289 false 5.879,0.221 6.146,0.461 0.267,0.239 10 *a 5.365,1.361 5.365,0.296 5.365,0.296 5.856,0.296 false 0.618,1.517 0.289,1.517 false 2.897,1.516 3.155,1.516 false 4.364,1.525 4.059,1.525 false 6.538,1.522 6.748,1.522 false 0.696,2.057 0.906,2.057 false 3.026,1.981 3.293,2.221 0.267,0.239 10 *c 2.818,2.057 3.028,2.057 false 4.648,2.002 4.915,2.242 0.267,0.239 10 *c 4.44,2.078 4.65,2.078 false 6.77,2.002 7.037,2.242 0.267,0.239 10 *c 6.563,2.078 6.773,2.078 false
*A for Short Body, for Single Cab *B for Semi-long Body, for Double Cab
*a Fender Relief *b Perforation
*c Front Door End Line - -



Hide 75985 5.INSTALL FRONT DOOR STRIPE RH

HINT:

Use the same procedure described for the LH side.


Hide 75992A 6.INSTALL QUARTER STRIPE

a.

for Short Body, w/ Over Fender:

HINT:

Use the same procedure for the RH and LH side.


i.
B324844C01
1.49,0.885 1.781,0.635 1.781,0.635 2.135,0.635 false 1.469,1.885 0.813,1.885 true 2.698,1.646 2.698,2.594 2.698,2.594 2.396,2.594 true 2.188,0.552 2.417,0.792 0.229,0.24 10 false *a 0.625,1.792 0.854,2.031 0.229,0.24 10 false *b 2.24,2.5 2.573,2.813 0.333,0.313 10 false *c
*a Quarter End Line
*b Perforation
*c Quarter Relief


Align the top of the application sheet of new stripe tape with the quarter relief and the perforation with the quarter end line as shown in the illustration, and then apply the stripe tape.


ii.

Remove the application sheet from the stripe tape.



b.

for Short Body, w/o Over Fender:

i.

Align the top of the application sheet of new stripe tape with the quarter relief and the perforations with the quarter end line and rear combination light end line as shown in the illustration, and then apply the stripe tape.


ii.

Remove the application sheet from the stripe tape.

B324845C01
1.521,1.219 1.521,0.292 1.521,0.292 1.865,0.292 true 5.281,1.219 5.281,0.271 5.281,0.271 5.615,0.271 true 0.781,1.302 0.365,1.302 true 2.844,1.292 3.156,1.292 false 4.208,1.281 4,1.281 true 6.271,1.292 6.521,1.292 true 0.74,1.729 0.354,1.729 false 2.833,1.563 3.146,1.563 false 6.292,1.688 6.521,1.688 false 4.01,1.542 4.198,1.542 true 4.479,1.302 4.708,0.406 4.708,0.406 4.906,0.406 false 0.302,0.125 0.552,0.354 0.25,0.229 10 false *A 3.823,0.104 4.073,0.333 0.25,0.229 10 false *B 1.875,0.219 2.104,0.438 0.229,0.219 10 false *a 0.177,1.219 0.406,1.438 0.229,0.219 10 false *b 0.198,1.646 0.427,1.865 0.229,0.219 10 false *c 6.563,1.615 6.792,1.833 0.229,0.219 10 false *c 3.156,1.49 3.385,1.708 0.229,0.219 10 false *d 3.854,1.458 4.083,1.677 0.229,0.219 10 false *d 3.156,1.208 3.385,1.427 0.229,0.219 10 false *b 3.854,1.198 4.083,1.417 0.229,0.219 10 false *b 6.552,1.219 6.781,1.438 0.229,0.219 10 false *b 4.927,0.333 5.156,0.552 0.229,0.219 10 false *b 5.656,0.208 5.885,0.427 0.229,0.219 10 false *a
*A for LH Side *B for RH Side
*a Quarter Relief *b Perforation
*c Quarter End Line *d Rear Combination Light End Line




Hide 75994B 7.INSTALL REAR QUARTER STRIPE

a.

for Short Body, w/ Over Fender:

i.

Align the top of the application sheet of new stripe tape with the quarter relief and the perforation with the rear combination light end line as shown in the illustration, and then apply the stripe tape.


ii.

Remove the application sheet from the stripe tape.

B324846C01
0.979,1.146 0.979,0.188 0.979,0.188 1.208,0.188 true 5.917,1.146 5.917,0.188 5.917,0.188 6.146,0.188 true 2.604,1.344 3.052,1.344 true 4.583,1.354 4.156,1.354 true 2.604,1.688 3.042,1.688 true 4.177,1.698 4.594,1.698 true 4.979,1.104 5.313,0.177 5.313,0.177 5.521,0.177 true 0.313,0.094 0.625,0.344 0.313,0.25 10 false *A 3.927,0.115 4.24,0.365 0.313,0.25 10 false *B 1.24,0.104 1.469,0.333 0.229,0.229 10 false *a 3.073,1.25 3.302,1.479 0.229,0.229 10 false *b 4.01,1.604 4.24,1.833 0.229,0.229 10 false *c 3.073,1.604 3.302,1.833 0.229,0.229 10 false *c 4,1.271 4.229,1.5 0.229,0.229 10 false *b 5.552,0.094 5.781,0.323 0.229,0.229 10 false *b 6.177,0.094 6.406,0.323 0.229,0.229 10 false *a
*A for LH Side *B for RH Side
*a Quarter Relief *b Perforation
*c Rear Combination Light End Line - -




b.

for Semi-long Body, w/o Over Fender:

i.

Align the top of the application sheet of new stripe tape with the quarter relief and the perforations with the quarter end line and rear combination light end line as shown in the illustration, and then apply the stripe tape.


ii.

Remove the application sheet from the stripe tape.

B324847C01
1.708,1.167 1.708,0.208 1.708,0.208 2.021,0.208 true 4.448,1.177 4.448,0.219 4.448,0.219 4.771,0.219 false 1.01,1.26 0.469,1.26 true 2.906,1.229 3.24,1.229 true 3.885,1.229 4.25,1.229 true 6.156,1.25 6.74,1.25 true 0.458,0.677 1.073,0.677 false 2.927,1.573 3.229,1.573 true 3.885,1.563 4.25,1.563 true 6.135,0.802 6.573,0.802 true 4.885,1.219 5.26,0.188 5.26,0.188 5.469,0.188 true 0.156,0.094 0.427,0.344 0.271,0.25 10 false *A 3.729,0.156 4,0.406 0.271,0.25 10 false *B 2.052,0.125 2.302,0.354 0.25,0.229 10 false *a 0.302,1.167 0.552,1.396 0.25,0.229 10 false *b 0.323,0.583 0.573,0.813 0.25,0.229 10 false *c 6.604,0.708 6.854,0.938 0.25,0.229 10 false *c 3.26,1.479 3.51,1.708 0.25,0.229 10 false *d 3.74,1.479 3.99,1.708 0.25,0.229 10 false *d 3.26,1.135 3.51,1.365 0.25,0.229 10 false *b 3.729,1.146 3.979,1.375 0.25,0.229 10 false *b 5.5,0.115 5.75,0.344 0.25,0.229 10 false *b 6.76,1.167 7.01,1.396 0.25,0.229 10 false *b 4.802,0.135 5.052,0.365 0.25,0.229 10 false *a
*A for LH Side *B for RH Side
*a Quarter Relief *b Perforation
*c Quarter End Line *d Rear Combination Light End Line




c.

for Semi-long Body, w/ Over Fender:

i.

Align the top of the application sheet of new stripe tape with the quarter relief and the perforation with the rear combination light end line as shown in the illustration, and then apply the stripe tape.


ii.

Remove the application sheet from the stripe tape.

B324848C01
1.5,1.365 1.75,0.24 1.75,0.24 2,0.24 true 5.688,1.354 5.448,0.229 5.448,0.229 5.229,0.229 false 2.938,1.448 3.219,1.448 true 4.24,1.438 3.927,1.438 true 5.167,1.427 4.875,0.417 4.875,0.417 4.698,0.417 true 2.938,1.74 3.229,1.74 true 3.896,1.74 4.24,1.74 true 0.344,0.115 0.594,0.375 0.25,0.26 10 false *A 3.656,0.146 3.906,0.406 0.25,0.26 10 false *B 3.24,1.365 3.479,1.615 0.24,0.25 10 false *b 3.26,1.656 3.5,1.906 0.24,0.25 10 false *c 3.75,1.656 3.99,1.906 0.24,0.25 10 false *c 3.76,1.365 4,1.615 0.24,0.25 10 false *b 4.51,0.344 4.75,0.594 0.24,0.25 10 false *b 5.063,0.146 5.302,0.396 0.24,0.25 10 false *a 2.021,0.156 2.26,0.406 0.24,0.25 10 false *a
*A for LH Side *B for RH Side
*a Quarter Relief *b Perforation
*c Rear Combination Light End Line - -




Hide 75979 8.INSTALL FUEL FILLER OPENING LID STRIPE

a.

for Short Body:

i.

Align the top of the application sheet of new stripe tape with the fuel filler opening lid relief and the perforations with the fuel filler opening lid end line as shown in the illustration, and then apply the stripe tape.


ii.

Remove the application sheet from the stripe tape.

B324849C01
1.417,0.563 1.74,0.563 1.74,0.563 1.74,1.417 true 4.781,0.563 5.094,0.563 5.094,0.563 5.094,1.5 true 2.25,1.719 2.708,2.052 2.708,2.052 2.958,2.052 true 1.615,1.76 1.333,1.76 true 5.583,1.615 5.99,2.156 5.99,2.156 6.156,2.156 true 4.938,1.667 4.656,1.667 true 1.646,2 1.479,2.146 1.479,2.146 1.365,2.146 true 4.979,2 4.854,2.156 4.854,2.156 4.667,2.156 false 0.292,0.115 0.563,0.365 0.271,0.25 10 false *A 3.802,0.125 4.073,0.375 0.271,0.25 10 false *B 1.24,0.469 1.458,0.698 0.219,0.229 10 false *a 2.99,1.99 3.208,2.219 0.219,0.229 10 false *b 1.156,1.677 1.375,1.906 0.219,0.229 10 false *b 1.208,2.052 1.427,2.281 0.219,0.229 10 false *c 4.625,0.469 4.844,0.698 0.219,0.229 10 false *a 6.188,2.073 6.406,2.302 0.219,0.229 10 false *b 4.5,1.594 4.719,1.823 0.219,0.229 10 false *b 4.521,2.052 4.74,2.281 0.219,0.229 10 false *c
*A w/o Over Fender *B w/ Over Fender
*a Fuel Filler Opening Lid Relief *b Perforation
*c Fuel Filler Opening End Line - -




b.

for Semi-long Body:

i.
B324850C01
1.719,1.552 1.719,0.563 1.719,0.563 2.135,0.563 true 1.323,1.865 0.854,1.865 true 2.115,1.802 2.448,1.156 2.448,1.156 2.656,1.156 true 1.354,2.135 1.25,2.365 1.25,2.365 1.021,2.365 false 2.167,0.458 2.406,0.708 0.24,0.25 10 false *a 0.688,1.781 0.927,2.031 0.24,0.25 10 false *b 0.865,2.271 1.104,2.521 0.24,0.25 10 false *c 2.688,1.073 2.927,1.323 0.24,0.25 10 false *b
*a Fuel Filler Opening Lid Relief
*b Perforation
*c Fuel Filler Opening Lid End Line


Align the top of the application sheet of new stripe tape with the fuel filler opening lid relief and the perforations with the fuel filler opening lid end line as shown in the illustration, and then apply the stripe tape.


ii.

Remove the application sheet from the stripe tape.



Hide 75988C 9.INSTALL REAR DOOR OUTSIDE STRIPE LH

a.

for Semi-long Body:

i.

Align the top of the application sheet of new stripe tape with the rear door relief and the perforation with the rear door end line as shown in the illustration, and then apply the stripe tape.


ii.

Remove the application sheet from the stripe tape.

B324851C01
1.75,1.333 1.75,0.219 1.75,0.219 2.177,0.219 true 4.927,1.333 4.927,0.135 4.927,0.135 5.344,0.135 true 1,1.521 0.698,1.521 false 2.927,1.406 3.229,1.406 true 4.281,1.51 3.844,1.51 true 0.698,1.979 1.063,1.979 false 3.854,2.021 4.313,2.021 false 2.979,1.115 3.271,1.115 false 0.292,0.125 0.594,0.375 0.302,0.25 10 false *A 2.219,0.135 2.521,0.385 0.302,0.25 10 false *a 0.552,1.427 0.854,1.677 0.302,0.25 10 false *b 0.552,1.896 0.854,2.146 0.302,0.25 10 false *c 3.698,1.938 4,2.188 0.302,0.25 10 false *c 3.302,1.021 3.604,1.271 0.302,0.25 10 false *c 3.26,1.333 3.563,1.583 0.302,0.25 10 false *b 3.688,1.427 3.99,1.677 0.302,0.25 10 false *b 3.656,0.135 3.958,0.385 0.302,0.25 10 false *B 5.396,0.063 5.698,0.313 0.302,0.25 10 false *a
*A w/o Over Fender *B w/ Over Fender
*a Rear Door Relief *b Perforation
*c Rear Door End Line - -




b.
B324858C01
1.292,1.771 1.292,0.417 1.292,0.417 1.677,0.417 true 0.552,2.021 0.333,2.021 true 2.594,1.958 2.854,2.625 2.854,2.625 3.031,2.625 true 2.25,1.906 2.25,0.688 2.25,0.688 2.677,0.688 true 0.594,2.5 0.938,2.5 false 2,2.344 1.635,2.344 false 1.719,0.333 2.01,0.594 0.292,0.26 10 false *a 0.177,1.938 0.365,2.198 0.188,0.26 10 false *b 3.073,2.552 3.26,2.813 0.188,0.26 10 false *b 2.719,0.604 2.906,0.865 0.188,0.26 10 false *b 2.021,2.24 2.208,2.5 0.188,0.26 10 false *c 0.969,2.417 1.156,2.677 0.188,0.26 10 false *c
*a Rear Door Relief
*b Perforation
*c Rear Door End Line


for Double Cab:

i.

Align the top of the application sheet of new stripe tape with the rear door relief and the perforations with the rear door end lines as shown in the illustration, and then apply the stripe tape.


ii.

Remove the application sheet from the stripe tape.



Hide 75987C 10.INSTALL REAR DOOR OUTSIDE STRIPE RH

HINT:

Use the same procedure described for the LH side.


Hide 75942 11.INSTALL NO. 2 CENTER PILLAR STRIPE

B324852C01
1.313,1.75 0.938,1.75 true 1.635,2.479 1.281,2.479 false 1.417,1.427 1.417,0.802 1.417,0.802 1.688,0.802 true 1.729,0.719 1.927,0.938 0.198,0.219 10 false *a 0.76,1.656 0.958,1.875 0.198,0.219 10 false *b 1.656,2.396 1.854,2.615 0.198,0.219 10 false *c
*a Center Pillar Relief
*b Perforation
*c Center Pillar End Line


a.

Align the top of the application sheet of new stripe tape with the center pillar relief and the perforation with the center pillar end line as shown in the illustration, and then apply the stripe tape.


b.

Remove the application sheet from the stripe tape.


Hide 75989 12.INSTALL REAR DECK FRONT STRIPE LH

B324853C01
0.823,1.635 0.354,1.635 true 2.542,1.531 2.542,0.646 2.542,0.646 2.156,0.646 true 0.24,1.948 0.823,1.948 true 2.833,1.427 2.833,0.167 2.833,0.167 2.438,0.167 false 2.271,0.083 2.615,0.365 0.344,0.281 10 false *a 0.177,1.563 0.521,1.844 0.344,0.281 10 false *b 2,0.563 2.344,0.844 0.344,0.281 10 false *b 0.083,1.875 0.427,2.156 0.344,0.281 10 false *c
*a Rear Body Side Panel Relief
*b Perforation
*c Rear Body Side Panel End Line


a.

Align the top of the application sheet of new stripe tape with the rear body side panel relief and the perforation with the rear body side panel end line as shown in the illustration, and apply the stripe tape.


b.

Remove the application sheet from the stripe tape.


Hide 75988B 13.INSTALL REAR DECK FRONT STRIPE RH

HINT:

Use the same procedure described for the LH side.


Hide 75999C 14.INSTALL REAR DECK REAR STRIPE LH (for Single Cab, for Double Cab)

B324854C01
2.344,0.219 2.667,0.219 2.667,0.219 3.073,0.917 true 0.844,1.167 0.844,0.323 0.844,0.323 0.531,0.323 true 2.667,0.229 2.667,1.094 true 3.083,1.333 2.323,2.479 2.323,2.479 2.094,2.479 true 2.167,0.125 2.469,0.375 0.302,0.25 10 false *a 0.375,0.24 0.677,0.49 0.302,0.25 10 false *b 1.906,2.396 2.208,2.646 0.302,0.25 10 false *b
*a Rear Body Side Panel Relief
*b Perforation


a.

Align the top and the rear side perforation of the application sheet of new stripe tape with the rear body side panel relief as shown in the illustration, and then apply the stripe tape.


b.

Remove the application sheet from the stripe tape.


Hide 75998C 15.INSTALL REAR DECK REAR STRIPE RH (for Single Cab)

HINT:

Use the same procedure described for the LH side.


a.

for Fuel Sub Tank:

i.
B324855C01
0.365,1.083 0.656,0.458 0.656,0.458 0.969,0.458 true 0.656,0.458 0.75,1.323 true 2.563,1.406 2.563,0.469 2.563,0.469 2.969,0.469 true 1.76,1.458 1.76,0.479 1.76,0.479 2.125,0.479 true 0.365,1.615 1.104,2.719 1.104,2.719 1.333,2.719 true 0.979,0.375 1.24,0.625 0.26,0.25 10 false *a 3.01,0.385 3.271,0.635 0.26,0.25 10 false *b 2.156,0.406 2.417,0.656 0.26,0.25 10 false *b 1.375,2.635 1.635,2.885 0.26,0.25 10 false *b
*a Rear Body Side Panel Relief
*b Perforation


Align the top and the rear side perforation of the application sheet of new stripe tape with the rear body side panel relief as shown in the illustration, and then apply the stripe tape.


ii.

Remove the application sheet from the stripe tape.



Hide 75998C 16.INSTALL REAR DECK REAR STRIPE RH (for Double Cab)

a.
B324855C01
0.365,1.083 0.656,0.458 0.656,0.458 0.969,0.458 true 0.656,0.458 0.75,1.323 true 2.563,1.406 2.563,0.469 2.563,0.469 2.969,0.469 true 1.76,1.458 1.76,0.479 1.76,0.479 2.125,0.479 true 0.365,1.615 1.104,2.719 1.104,2.719 1.333,2.719 true 0.979,0.375 1.24,0.625 0.26,0.25 10 false *a 3.01,0.385 3.271,0.635 0.26,0.25 10 false *b 2.156,0.406 2.417,0.656 0.26,0.25 10 false *b 1.375,2.635 1.635,2.885 0.26,0.25 10 false *b
*a Rear Body Side Panel Relief
*b Perforation


Align the top and the rear side perforation of the application sheet of new stripe tape with the rear body side panel relief as shown in the illustration, and then apply the stripe tape.


b.

Remove the application sheet from the stripe tape.