Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for 1HZ)
RM25T0E _58 Vehicle Interior _029469 HEATING / AIR CONDITIONING _0137761 COMPRESSOR(for 1HZ) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 1HZ)  REASSEMBLY  


PROCEDURE

Hide 88410 1.INSTALL MAGNET CLUTCH ASSEMBLY

E192931

a.

Install the magnet clutch stator with the parts shown in the illustration matched.


b.
I032461

Using a snap ring expander, install a new snap ring with the chamfered side facing up.


c.

Connect the connector.


d.
I031582

Using a snap ring expander, install the magnet clutch rotor and a new snap ring with the chamfered side facing up.

NOTICE:

Do not damage the seal cover of the bearing when installing the snap ring.



e.

Install the magnet clutch washer(s) and magnet clutch hub.

NOTICE:

Do not change the combination of the magnet clutch washer(s) used before disassembly.



f.
E192933C01
0.417,1 0.813,1 false 0.521,3.427 0.917,3.427 false 0.042,0.094 0.354,0.25 0.313,0.156 10 false *A 0.073,2.469 0.385,2.625 0.313,0.156 10 false *B 0.281,0.938 0.594,1.094 0.313,0.156 10 false *1 0.354,3.354 0.667,3.51 0.313,0.156 10 false *1
*A for Type A
*B for Type B
*1 SST


Using SST, hold the magnet clutch hub and install the bolt.

SST
09985-00270  

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Make sure that there is no foreign matter or oil on the compressor shaft, bolt, and clutch hub.



Hide 2.INSTALL COOLER BRACKET

E192926C02
0.031,0.073 0.344,0.229 0.313,0.156 10 false *A 0.052,2.427 0.365,2.583 0.313,0.156 10 false *B
*A for Type A
*B for Type B


a.

Install the cooler bracket with the screw.


b.

Attach the clamp.


Hide 3.INSPECT MAGNET CLUTCH CLEARANCE

E194285C01
0.677,2.406 1.229,2.406 true 2.896,3.948 3.208,4.104 0.313,0.156 10 false *2 0.25,0.688 0.563,0.844 0.313,0.156 10 false *a 0.521,2.333 0.833,2.49 0.313,0.156 10 false *1
*1 Ground Wire
*2 Battery
*a Component without harness connected
(Magnet Clutch Assembly)


a.

Clamp the cooler compressor in a vise.


b.

Set the dial indicator to the magnet clutch hub.


c.

Connect the battery positive lead to terminal 1 of the magnet clutch connector and the negative lead to the ground wire. Turn the magnet clutch on and off and measure the clearance.

Standard clearance:

0.35 to 0.60 mm (0.014 to 0.024 in.)


If the measured value is not within the standard clearance, remove the magnet clutch hub and adjust the clearance using magnet clutch washers to obtain the standard clearance.

NOTICE:

Adjustment should be performed with 3 or fewer magnet clutch washers.



d.

Remove the compressor assembly with magnet clutch from the vise.