Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
84306 1.INSTALL SPIRAL CABLE SUB-ASSEMBLY
Check that the spiral cable sub-assembly is center position.
The connector is at the top.
The matchmarks are aligned.
The colored roller or the top of the flat cable U-turn can be checked from the check window.
| *A | Colored Roller (Visible Type) | *B | Flat Cable (Visible Type) |
| *a | Check Window | *b | Matchmark |
| *c | Colored Roller | *d | Top of Flat Cable U-turn |
If the spiral cable sub-assembly is not centered, center it.
Failure to observe the following precautions may result in damage to the spiral cable sub-assembly.
Do not turn the spiral cable sub-assembly using the airbag wire harness.
Do not forcibly rotate the part.
|
Counterclockwise |
Make sure to rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.
Make sure to rotate the spiral cable sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.
If the spiral cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.
|
Clockwise |
Rotate the spiral cable sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.
If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.
Check that the spiral cable sub-assembly is center position.
The connector is at the top.
The matchmarks are aligned.
The colored roller or the top of the flat cable U-turn can be checked from the check window.
| *A | Colored Roller (Visible Type) | *B | Flat Cable (Visible Type) |
| *a | Check Window | *b | Matchmark |
| *c | Colored Roller | *d | Top of Flat Cable U-turn |
If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.
84306 2.INSTALL SPIRAL CABLE SUB-ASSEMBLY
|
Lock Pin |
When replacing the spiral cable sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the front wheels are facing straight ahead.
Set the turn signal switch to the neutral position.
If it is not in the neutral position, the turn signal switch cancel ratchet may snap.
| *1 | Slider |
Attach the 3 claws to install the spiral cable sub-assembly.
Connect the connectors to the spiral cable sub-assembly.
When handling the airbag connector, do not damage the airbag wire harness.
45286B 3.INSTALL UPPER STEERING COLUMN COVER
45287 4.INSTALL LOWER STEERING COLUMN COVER
84306 5.ADJUST SPIRAL CABLE SUB-ASSEMBLY
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Check that the spiral cable sub-assembly is center position.
The connector is at the top.
The matchmarks are aligned.
The colored roller or the top of the flat cable U-turn can be checked from the check window.
| *A | Colored Roller (Visible Type) | *B | Flat Cable (Visible Type) |
| *a | Check Window | *b | Matchmark |
| *c | Colored Roller | *d | Top of Flat Cable U-turn |
If the spiral cable sub-assembly is not centered, center it.
Failure to observe the following precautions may result in damage to the spiral cable sub-assembly.
Do not turn the spiral cable sub-assembly using the airbag wire harness.
Do not forcibly rotate the part.
|
Counterclockwise |
Make sure to rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.
Make sure to rotate the spiral cable sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.
If the spiral cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.
|
Clockwise |
Rotate the spiral cable sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.
If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.
Check that the spiral cable sub-assembly is center position.
The connector is at the top.
The matchmarks are aligned.
The colored roller or the top of the flat cable U-turn can be checked from the check window.
| *A | Colored Roller (Visible Type) | *B | Flat Cable (Visible Type) |
| *a | Check Window | *b | Matchmark |
| *c | Colored Roller | *d | Top of Flat Cable U-turn |
If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.
55480D 6.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
45100 7.INSTALL STEERING WHEEL ASSEMBLY
8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
9.PERFORM DIAGNOSTIC SYSTEM CHECK
10.CHECK SRS WARNING LIGHT