Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › CENTER AIRBAG SENSOR ASSEMBLY › 2014.08–2016.08
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0138001 CENTER AIRBAG SENSOR ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  CENTER AIRBAG SENSOR ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 89170 1.INSTALL CENTER AIRBAG SENSOR ASSEMBLY

a.
E298622N01
2.521,0.906 2.771,1.135 0.25,0.229 10 false (1) 1.521,0.052 1.771,0.281 0.25,0.229 10 false (2) 0.354,0.26 0.604,0.49 0.25,0.229 10 false (3)

Temporarily install the center airbag sensor assembly to the airbag sensor bracket with the 3 bolts.


b.

Tighten the 3 bolts order shown in the illustration.

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)


Hide 89175 2.INSTALL AIRBAG SENSOR BRACKET

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the waterproof sheet is properly set.


d.

Temporarily install the airbag sensor bracket with the 3 bolts.

NOTICE:
·

If the airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace airbag sensor assembly with a new one.

·

When installing the airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.




e.
B374349C01
0.365,1.167 0.781,0.75 true 2.177,2.302 2.604,3.146 2.604,3.146 2.854,3.146 true 0.198,1.104 0.51,1.26 0.313,0.156 10 false *1 2.927,3.063 3.208,3.25 0.281,0.188 10 true *2 2.208,2.813 2.406,3.042 0.198,0.229 10 true (1) 0.729,2.865 0.969,3.094 0.24,0.229 10 true (2) 2.135,1.656 2.375,1.885 0.24,0.229 10 true (3)
*1 Connector Lock
*2 Waterproof Sheet


Tighten the 3 bolts order shown in the illustration.

Torque:
17.5 N*m (178 kgf*cm, 13 ft.*lbf)


f.

Connect the airbag connector and push the connector lock to lock the airbag connector.

NOTICE:
·

When handling any airbag connector, take care not to damage the airbag wire harness.

·

Do not allow the water proof sheet to become pinched.




g.

Check that there is no looseness in the installation parts of the center airbag sensor assembly.


Hide 89179A 3.INSTALL AIRBAG SENSOR COVER

a.
B234336N01
2.5,0.188 2.76,0.438 0.26,0.25 10 true (1) 1.479,1.917 1.677,2.135 0.198,0.219 10 true (2) 0.781,1.875 0.979,2.094 0.198,0.219 10 true (3)

Temporarily install the airbag sensor cover with the 3 bolts.


b.

Tighten the 3 bolts order shown in the illustration.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)


Hide 5. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL