Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB
RM25T0E _52 Drivetrain _029907 AXLE AND DIFFERENTIAL _0138018 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.REMOVE FRONT WHEEL

Hide 2.DISCONNECT FRONT SPEED SENSOR LH (w/ ABS)

a.
C271615

Remove the nut and disconnect the front speed sensor LH.

NOTICE:
·

Be careful not to damage the speed sensor.

·

Prevent foreign matter from adhering to the speed sensor.




Hide 3.REMOVE FRONT DISC BRAKE CYLINDER ASSEMBLY LH

a.
C271619

Remove the 2 bolts and front disc brake cylinder assembly.

NOTICE:

Use wire or an equivalent tool to keep the brake cylinder from hanging down by the flexible hose.



Hide 43423 4.REMOVE FRONT AXLE OUTER SHAFT FLANGE CAP (w/o Free Wheel Hub)

a.
C271617

Using a screwdriver and hammer, remove the front axle outer shaft flange cap from the flange.


Hide 43421F 5.REMOVE FRONT AXLE OUTER SHAFT FLANGE LH (w/o Free Wheel Hub)

a.
C271618

Using a snap ring expander, remove the snap ring.


b.

Remove the 6 nuts and 6 washers.


c.
C271620

Using a brass bar and hammer, tap on the 6 bolt heads and remove the 6 cone washers.


d.

Remove the front axle outer shaft flange LH.


e.

Remove the front axle outer shaft flange gasket LH.


Hide 43530 6.REMOVE FREE WHEEL HUB ASSEMBLY (w/ Free Wheel Hub)

a.

Set the control handle to FREE.


b.

Remove the 6 bolts, free wheel hub cover and gasket.


c.
C304445

Using a snap ring expander, remove the snap ring.


d.

Remove the 6 nuts and 6 washers.


e.
C304446

Using a brass bar and hammer, tap on the 6 bolt heads and remove the 6 cone washers.


f.

Remove the free wheel hub body and gasket.


Hide 43530 7.REMOVE DUAL MODE AUTOMATIC LOCKING HUB (w/ Dual Mode Automatic Locking Hub)

a.
C305651

Using a hub nut wrench, set the knob of the dual mode automatic locking hub to ''LOCK'' position.


b.
C305652

Using a 8 mm hexagon wrench, remove the 6 hexagon bolts and locking hub and gasket.


c.

Using a snap ring expander, remove the snap ring.


d.

Remove the front drive shaft spacer LH and brake set.


Hide 43502C 8.REMOVE FRONT AXLE HUB AND FRONT DISC (w/ Dual Mode Automatic Locking Hub)

a.
C305894N01
2.458,1.292 2.688,1.01 2.688,1.01 2.896,1.01 false 2.958,0.938 3.323,1.135 0.365,0.198 10 false SST

Using SST, remove the front wheel adjusting nut LH.

SST
09607-60020  


b.

Remove the front axle hub and front disc together with the outer bearing.


Hide 43502C 9.REMOVE FRONT AXLE HUB AND FRONT DISC (w/o Dual Mode Automatic Locking Hub)

a.
C271623

Using a screwdriver, loosen the front wheel adjusting lock washer.


b.
C305893N01
2.469,1.354 2.635,1.073 2.635,1.073 2.896,1.073 false 2.958,1 3.281,1.198 0.323,0.198 10 false SST

Using SST, remove the front wheel adjusting nut LH.

SST
09607-60020  


c.

Remove the front wheel adjusting lock washer.


d.

Using SST, remove the front wheel adjusting nut LH and front axle hub claw washer LH.

SST
09607-60020  


e.

Remove the front axle hub and front disc together with the outer bearing.


Hide 43502F 10.REMOVE FRONT AXLE HUB OIL SEAL LH

a.
C271624N01
0.76,0.479 1.313,0.479 1.313,0.479 1.823,0.969 false 0.438,0.406 0.896,0.604 0.458,0.198 10 false SST

Using SST, remove the front axle hub oil seal LH.

SST
09308-00010  

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.




Hide 11.REMOVE INNER BEARING

a.

Remove the inner bearing from the front axle hub.


Hide 12.REMOVE BEARING OUTER RACE

a.
C271625

Using a brass bar and hammer, remove the 2 bearing outer races.


Hide 43512 13.REMOVE FRONT DISC

a.
C271626C01
1.958,0.677 2.448,0.281 2.448,0.281 2.771,0.281 true 2.865,0.208 3.177,0.365 0.313,0.156 10 false *a
*a Matchmark


Place matchmarks on the front axle hub and front disc.


b.

Remove the 5 bolts and disc from the front axle hub.

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.