Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING PANEL
RM25T0E _58 Vehicle Interior _029469 HEATING / AIR CONDITIONING _0137766 AIR CONDITIONING PANEL G

HEATING / AIR CONDITIONING  AIR CONDITIONING PANEL  INSPECTION  


PROCEDURE

Hide 84730 1.INSPECT HEATER BLOWER SWITCH ASSEMBLY (for LHD)

a.
B382736C01
1.094,0.063 1.25,0.26 0.156,0.198 10 false 0 2.073,0.333 2.229,0.531 0.156,0.198 10 false 1 2.813,1.073 2.969,1.271 0.156,0.198 10 false 2 3.052,2.042 3.208,2.24 0.156,0.198 10 false 3 2.802,2.99 2.958,3.188 0.156,0.198 10 false 4 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a
*a Component without harness connected
(Heater Blower Switch Assembly)


Check the blower control resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Position Specified Condition
All Terminal - 1 0 10 kΩ or higher
1 - 8
1 - 7
1 Below 1 Ω
1 - 8
1 - 6
2 Below 1 Ω
1 - 8
1 - 5
3 Below 1 Ω
1 - 8
1 - 4
4 Below 1 Ω


If the result is not as specified, replace the heater blower switch assembly.



b.
B382737C01
1.167,0.115 1.479,0.271 0.313,0.156 10 false *b 2.74,1.146 3.052,1.302 0.313,0.156 10 false *c 2.813,3 3.125,3.156 0.313,0.156 10 false *d
*a Component without harness connected
(Heater Blower Switch Assembly)
*b OFF
*c ON
*d Max Cool


w/ Cooler System:

Check the cooler volume resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Position Specified Condition
2 - 3 OFF 10 kΩ or higher
2 - 3 ON to Max Cool 3.6 kΩ to 6.6 Ω


If the result is not as specified, replace the heater blower switch assembly.



Hide 84730 2.INSPECT HEATER BLOWER SWITCH ASSEMBLY (for RHD)

a.
B382713C01
0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 2.26,0.052 2.417,0.25 0.156,0.198 10 false 0 1.271,0.302 1.427,0.5 0.156,0.198 10 false 1 0.563,1.063 0.719,1.26 0.156,0.198 10 false 2 0.302,2.052 0.458,2.25 0.156,0.198 10 false 3 0.563,3.021 0.719,3.219 0.156,0.198 10 false 4
*a Component without harness connected
(Heater Blower Switch Assembly)


Check the blower control resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Position Specified Condition
All Terminal - 1 0 10 kΩ or higher
1 - 8
1 - 7
1 Below 1 Ω
1 - 8
1 - 6
2 Below 1 Ω
1 - 8
1 - 5
3 Below 1 Ω
1 - 8
1 - 4
4 Below 1 Ω


If the result is not as specified, replace the heater blower switch assembly.



b.
B382735C01
0.063,0.063 0.375,0.219 0.313,0.156 10 false *a 2.115,0.104 2.427,0.26 0.313,0.156 10 false *b 0.521,1.188 0.833,1.344 0.313,0.156 10 false *c 0.479,3.021 0.792,3.177 0.313,0.156 10 false *d
*a Component without harness connected
(Heater Blower Switch Assembly)
*b OFF
*c ON
*d Max Cool


w/ Cooler System:

Check the cooler volume resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Position Specified Condition
2 - 3 OFF 10 kΩ or higher
2 - 3 ON to Max Cool 3.6 kΩ to 6.6 Ω


If the result is not as specified, replace the heater blower switch assembly.