Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT DIMMER SWITCH
RM25T0E _59 Vehicle Exterior _029940 LIGHTING (EXT) _0138178 HEADLIGHT DIMMER SWITCH G

LIGHTING (EXT)  HEADLIGHT DIMMER SWITCH  INSPECTION  


PROCEDURE

Hide 84140 1.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for LHD)

a.

Inspect the light control switch.

i.
E269874C23
1.5,0.406 1.958,0.635 0.458,0.229 1.052,1.208 0.594,1.208 true 1.448,1.667 1.375,1.292 true 2.26,1.667 2.188,1.292 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 1.438,1.698 1.594,1.896 0.156,0.198 10 false T 0.448,1.115 0.604,1.313 0.156,0.198 10 false H 2.198,1.688 2.51,1.885 0.313,0.198 10 false EL 1.625,0.438 2.083,0.635 0.458,0.198 10 false L24
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L24-18 (T) - L24-12 (EL) Light control switch off 10 kΩ or higher
L24-20 (H) - L24-12 (EL)
L24-18 (T) - L24-12 (EL) Light control switch tail position Below 1 Ω
L24-18 (T) - L24-12 (EL) Light control switch head position Below 1 Ω
L24-20 (H) - L24-12 (EL)


If the result is not as specified, replace the headlight dimmer switch assembly.



b.

Inspect the headlight dimmer switch.

i.
E269874C24
1.5,0.406 1.958,0.635 0.458,0.229 1.365,1.677 1.51,1.292 true 2.115,1.667 2.177,1.292 true 2.406,1.667 2.333,1.292 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 2.344,1.698 2.594,1.896 0.25,0.198 10 false HU 1.26,1.698 1.635,1.906 0.375,0.208 10 false HF 2.031,1.688 2.344,1.885 0.313,0.198 10 false EL 1.615,0.438 2.073,0.635 0.458,0.198 10 false L24
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L24-17 (HF) - L24-12 (EL) Headlight dimmer switch flash position Below 1 Ω
L24-11 (HU) - L24-12 (EL)
L24-11 (HU) - L24-12 (EL) Headlight dimmer switch high position Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.



c.

Inspect the turn signal light switch.

i.
E269874C25
1.5,0.406 1.958,0.635 0.458,0.229 1.625,1.677 1.771,1.292 true 1.979,1.667 2.042,1.292 true 2.26,1.667 2.188,1.292 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 1.875,1.698 2.167,1.896 0.292,0.198 10 false TR 1.531,1.708 1.906,1.917 0.375,0.208 10 false TL 2.208,1.698 2.521,1.896 0.313,0.198 10 false EL 1.615,0.438 2.073,0.635 0.458,0.198 10 false L24
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L24-13 (TR) - L24-12 (EL) Turn signal switch neutral position 10 kΩ or higher
L24-15 (TL) - L24-12 (EL)
L24-13 (TR) - L24-12 (EL) Turn signal switch right turn position
(self cancel condition)
Below 1 Ω
Turn signal switch right turn position
(cancel ratchet operation condition)
L24-15 (TL) - L24-12 (EL) Turn signal switch left turn position
(self cancel condition)
Below 1 Ω
Turn signal switch in left turn position
(cancel ratchet operation condition)


HINT:
·

The self cancel condition indicates when the turn signal switch returns to the neutral position when releasing your hand from the switch (switch is operated within 7°).

·

The cancel ratchet operation condition indicates the condition when the turn signal switch does not return to the neutral position even when releasing your hand (switch operation is 12°).



If the result is not as specified, replace the headlight dimmer switch assembly.



d.

Inspect the front fog light switch.

i.
E269874C26
1.51,0.396 1.958,0.625 0.448,0.229 1.875,1.031 2.219,0.208 2.219,0.208 2.573,0.208 true 2.094,1.031 2.385,0.542 2.385,0.542 2.698,0.542 true 0.094,0.104 0.406,0.26 0.313,0.156 10 false *a 2.646,0.125 3.104,0.323 0.458,0.198 10 false BFG 2.781,0.448 3.24,0.646 0.458,0.198 10 false LFG 1.625,0.438 2.083,0.635 0.458,0.198 10 false L24
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L24-4 (BFG) - L24-3 (LFG) Front fog light switch off 10 kΩ or higher
Front fog light switch on Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.



e.

Inspect the rear fog light switch.

i.
E269874C28
1.51,0.396 1.958,0.625 0.448,0.229 1.875,1.031 2.219,0.208 2.219,0.208 2.573,0.208 true 2.094,1.031 2.385,0.542 2.385,0.542 2.698,0.542 true 2.219,1.031 2.469,0.75 2.469,0.75 2.719,0.75 true 0.094,0.104 0.406,0.26 0.313,0.156 10 false *a 2.646,0.125 3.104,0.323 0.458,0.198 10 false BFG 2.781,0.448 3.24,0.646 0.458,0.198 10 false LFG 1.625,0.438 2.083,0.635 0.458,0.198 10 false L24 2.781,0.656 2.938,0.854 0.156,0.198 10 false B
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L24-2 (B) - L24-3 (LFG) Rear fog light switch off 10 kΩ or higher
L24-4 (BFG) - L24-3 (LFG)
L24-2 (B) - L24-3 (LFG) Rear fog light switch on Below 1 Ω
L24-4 (BFG) - L24-3 (LFG)


If the result is not as specified, replace the headlight dimmer switch assembly.



Hide 84140 2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for RHD)

a.

Inspect the light control switch.

i.
E269874C29
1.5,0.406 1.958,0.635 0.458,0.229 1.313,1.667 1.24,1.292 true 2.125,1.667 2.052,1.292 true 2.396,1.667 2.323,1.292 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 2.115,1.698 2.271,1.896 0.156,0.198 10 false T 2.365,1.698 2.521,1.896 0.156,0.198 10 false H 1.271,1.698 1.583,1.896 0.313,0.198 10 false EL 1.625,0.438 2.083,0.635 0.458,0.198 10 false L24
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L24-11 (H) - L24-19 (EL) Light control switch off 10 kΩ or higher
L24-13 (T) - L24-19 (EL)
L24-13 (T) - L24-19 (EL) Light control switch tail position Below 1 Ω
L24-11 (H) - L24-19 (EL) Light control switch head position Below 1 Ω
L24-13 (T) - L24-19 (EL)


If the result is not as specified, replace the headlight dimmer switch assembly.



b.

Inspect the headlight dimmer switch.

i.
E269874C30
1.5,0.406 1.958,0.635 0.458,0.229 1.104,1.677 1.25,1.292 true 1.865,1.667 1.927,1.292 true 0.646,1.177 1.073,1.177 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 0.406,1.104 0.656,1.302 0.25,0.198 10 false HU 1.75,1.698 2.125,1.906 0.375,0.208 10 false HF 1.021,1.698 1.333,1.896 0.313,0.198 10 false EL 1.615,0.438 2.073,0.635 0.458,0.198 10 false L24
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L24-14 (HF) - L24-19 (EL) Headlight dimmer switch flash position Below 1 Ω
L24-20 (HU) - L24-19 (EL)
L24-20 (HU) - L24-19 (EL) Headlight dimmer switch high position Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.



c.

Inspect the turn signal light switch.

i.
E269874C31
1.5,0.406 1.958,0.635 0.458,0.229 1.094,1.677 1.24,1.292 true 1.729,1.667 1.646,1.292 true 1.458,1.667 1.385,1.292 true 0.063,0.052 0.375,0.208 0.313,0.156 10 false *a 1.688,1.698 1.979,1.896 0.292,0.198 10 false TR 1.427,1.698 1.802,1.906 0.375,0.208 10 false TL 1.01,1.698 1.323,1.896 0.313,0.198 10 false EL 1.615,0.438 2.073,0.635 0.458,0.198 10 false L24
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L24-16(TR) - L24-19(EL) Turn signal switch neutral position 10 kΩ or higher
L24-18 (TL) - L24-19 (EL)
L24-16 (TR) - L24-19 (EL) Turn signal switch right turn position
(self cancel condition)
Below 1 Ω
Turn signal switch right turn position
(cancel ratchet operation condition)
L24-18 (TL) - L24-19 (EL) Turn signal switch left turn position
(self cancel condition)
Below 1 Ω
Turn signal switch in left turn position
(cancel ratchet operation condition)


HINT:
·

The self cancel condition indicates when the turn signal switch returns to the neutral position when releasing your hand from the switch (switch is operated within 7°).

·

The cancel ratchet operation condition indicates the condition when the turn signal switch does not return to the neutral position even when releasing your hand (switch operation is 12°).



If the result is not as specified, replace the headlight dimmer switch assembly.



d.

Inspect the front fog light switch.

i.
E269874C32
1.51,0.396 1.958,0.625 0.448,0.229 1.479,1.031 1.323,0.219 1.323,0.219 0.906,0.219 true 1.406,1.031 1.25,0.542 1.25,0.542 0.938,0.542 true 0.094,0.104 0.406,0.26 0.313,0.156 10 false *a 0.563,0.115 1.021,0.313 0.458,0.198 10 false BFG 0.625,0.438 1.083,0.635 0.458,0.198 10 false LFG 1.625,0.438 2.083,0.635 0.458,0.198 10 false L24
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L24-7 (BFG) - L24-8 (LFG) Front fog light switch off 10 kΩ or higher
Front fog light switch on Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.