Home › Vehicle Exterior › LIGHTING (EXT) › HAZARD WARNING SWITCH
RM25T0E _59 Vehicle Exterior _029940 LIGHTING (EXT) _0138188 HAZARD WARNING SWITCH G

LIGHTING (EXT)  HAZARD WARNING SWITCH  INSPECTION  


PROCEDURE

Hide 84330 1.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY (for 12 V Battery)

a.

Inspect the hazard warning signal switch assembly.

i.
E296899C01
1.469,0.115 1.885,0.375 0.417,0.26 2.281,0.885 2.781,0.885 true 2.063,1.01 2.063,1.313 2.063,1.313 2.51,1.313 true 0.073,0.083 0.385,0.24 0.313,0.156 10 false *a 2.583,1.219 2.74,1.417 0.156,0.198 10 false E 2.854,0.792 3.01,0.99 0.156,0.198 10 false F 1.563,0.156 2.021,0.354 0.458,0.198 10 false L14
*a Component without harness connected
(Hazard Warning Signal Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L14-5 (F) - L14-6 (E) Hazard warning signal switch off 10 kΩ or higher
L14-5 (F) - L14-6 (E) Hazard warning signal switch on Below 1 Ω


If the result is not as specified, replace the hazard warning signal switch assembly.



b.

Check the illumination.

i.

Apply battery voltage to the connector and check the illumination conditions.

OK:
Measurement Condition Specified Condition
Battery positive (+) → L14-8
Battery negative (-) → L14-9
Illuminates


If the result is not as specified, replace the hazard warning signal switch assembly.



Hide 84330 2.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY (for Canvas Top)

a.

Inspect the hazard warning signal switch assembly.

i.
E306177C02
1.479,0.24 1.917,0.49 0.438,0.25 2.083,1.438 2.083,1.875 2.083,1.875 2.635,1.875 true 2.302,1.313 2.833,1.313 true 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 2.698,1.781 3.01,1.938 0.313,0.156 10 false E 2.896,1.219 3.198,1.458 0.302,0.24 10 false F 1.594,0.281 2.021,0.479 0.427,0.198 10 false M1
*a Component without harness connected
(Hazard Warning Signal Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
M1-5 (F) - M1-6 (E) Hazard warning signal switch off 10 kΩ or higher
M1-5 (F) - M1-6 (E) Hazard warning signal switch on Below 1 Ω


If the result is not as specified, replace the hazard warning signal switch assembly.



Hide 84330 3.INSPECT HAZARD WARNING SIGNAL SWITCH ASSEMBLY (for 24 V Battery)

a.

Inspect the hazard warning signal switch assembly.

i.
E306177C01
1.479,0.24 1.917,0.49 0.438,0.25 0.583,1.083 1.115,1.083 true 2.063,1.063 2.063,0.646 2.063,0.646 2.479,0.646 true 2.302,1.083 2.833,1.083 true 0.083,0.073 0.396,0.229 0.313,0.156 10 false *a 0.438,0.99 0.75,1.146 0.313,0.156 10 false E 2.563,0.552 2.99,0.75 0.427,0.198 10 false TR 2.927,0.99 3.229,1.229 0.302,0.24 10 false TL 1.583,0.281 2.01,0.479 0.427,0.198 10 false L14
*a Component without harness connected
(Hazard Warning Signal Switch Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
L14-1 (TL) - L14-4 (E) Hazard warning signal switch off 10 kΩ or higher
L14-2 (TR) - L14-4 (E)
L14-1 (TL) - L14-4 (E) Hazard warning signal switch on Below 1 Ω
L14-2 (TR) - L14-4 (E)


If the result is not as specified, replace the hazard warning signal switch assembly.