Home › Vehicle Exterior › LIGHTING (EXT) › TURN SIGNAL FLASHER ASSEMBLY › 2014.08–2016.08
RM25T0E _59 Vehicle Exterior _029940 LIGHTING (EXT) _0138190 TURN SIGNAL FLASHER ASSEMBLY G

LIGHTING (EXT)  TURN SIGNAL FLASHER ASSEMBLY  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 81980 1.INSPECT TURN SIGNAL FLASHER ASSEMBLY (for 12 V Battery)

a.

Disconnect the connector from the turn signal flasher assembly.


b.
E303578C01
1.542,0.208 1.906,0.469 0.365,0.26 0.563,0.865 1.01,0.865 true 0.552,1.281 1,1.281 true 2.104,1.375 2.104,1.865 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 2.073,1.917 2.229,2.115 0.156,0.198 10 false E 0.396,1.188 0.552,1.385 0.156,0.198 10 false B 0.354,0.771 0.615,0.969 0.26,0.198 10 false IG 1.625,0.24 1.938,0.448 0.313,0.208 10 false I28
*a Front view of wire harness connector
(to Turn Signal Flasher Assembly)


Measure the resistance and voltage on the wire harness side connector according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I28-7 (E) - Body ground Always Below 1 Ω


Standard Voltage:
Tester Connection Condition Specified Condition
I28-4 (B) - I28-7 (E) Always 11 to 14 V
I28-1 (IG) - I28-7 (E) Ignition switch ON


If the result is not as specified, repair or replace the wire harness or connector.


c.

Connect the connector to the turn signal flasher assembly.


d.

Turn the ignition switch to ON.


e.
E157045C01
1.49,0.479 1.833,0.75 0.344,0.271 0.927,0.969 1.271,0.969 1.271,0.969 1.333,1.375 true 2.5,0.958 2.198,0.958 2.198,0.958 1.938,1.385 true 1.938,1.729 1.938,2.021 1.938,2.021 2.344,2.021 true 1.5,1.729 1.5,2.031 1.5,2.031 1.271,2.031 true 1.771,1.719 1.771,1.969 true 1.313,1.594 0.969,1.594 true 0.708,0.865 0.969,1.042 0.26,0.177 10 false LL 2.552,0.865 2.833,1.042 0.281,0.177 10 false LR 0.656,1.5 1.042,1.688 0.385,0.188 10 false HAZ 1.115,1.927 1.354,2.104 0.24,0.177 10 false E 1.677,1.99 1.969,2.146 0.292,0.156 10 false ER 2.406,1.917 2.594,2.094 0.188,0.177 10 false EL 1.573,0.521 1.833,0.698 0.26,0.177 10 false I28 0.073,0.073 0.385,0.229 0.313,0.156 10 false *a
*a Rear view of wire harness connector
(to Turn Signal Flasher Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I28-2 (LR) - I28-7 (E) Hazard warning switch off Below 1 V
Hazard warning switch on Alternating between 11 to 14 V and below 1 V
(60 to 120 times per minute)
Turn signal switch right turn position Alternating between 11 to 14 V and below 1 V
(60 to 120 times per minute)
I28-3 (LL) - I28-7 (E) Hazard warning switch off Below 1 V
Hazard warning switch on Alternating between 11 to 14 V and below 1 V
(60 to 120 times per minute)
Turn signal switch left turn position Alternating between 11 to 14 V and below 1 V
(60 to 120 times per minute)
I28-5 (EL) - I28-7 (E) Turn signal switch neutral position 9 V or higher
Turn signal switch left turn position Below 1 V
I28-6 (ER) - I28-7 (E) Turn signal switch neutral position 9 V or higher
Turn signal switch right turn position Below 1 V
I28-8 (HAZ) - I28-7 (E) Hazard warning switch off 9 V or higher
Hazard warning switch on Below 1 V


If the result is not as specified, replace the turn signal flasher assembly.


Hide 81980 2.INSPECT TURN SIGNAL FLASHER ASSEMBLY (for 24 V Battery)

a.

Disconnect the connector from the turn signal flasher assembly.


b.
E303576C03
1.51,0.385 1.906,0.656 0.396,0.271 0.74,1.177 1.135,1.177 true 0.073,0.073 0.385,0.229 0.313,0.156 10 false *a 0.573,1.073 0.729,1.271 0.156,0.198 10 false B 1.625,0.427 2.083,0.625 0.458,0.198 10 false I29
*a Front view of wire harness connector
(to Turn Signal Flasher Assembly)


Measure the voltage on the wire harness side connector according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I29-1 (B) - Body ground Always 22 to 26 V


If the result is not as specified, repair or replace the wire harness or connector.


c.

Connect the connector to the turn signal flasher assembly.


d.

Turn the ignition switch to ON.


e.
E303600C01
1.479,0.469 1.938,0.698 0.458,0.229 1.573,1.104 1.25,0.49 1.25,0.49 0.833,0.49 true 2.271,1.146 2.375,0.531 2.375,0.531 2.76,0.531 true 2.271,1.448 2.427,1.927 2.427,1.927 2.76,1.927 true 1.583,1.448 1.5,1.927 1.5,1.927 1.063,1.927 true 0.073,0.073 0.385,0.229 0.313,0.156 10 false *a 1.615,0.51 2.073,0.708 0.458,0.198 10 false I29 0.594,0.406 0.906,0.604 0.313,0.198 10 false FR 2.833,0.448 3.146,0.646 0.313,0.198 10 false LL 2.844,1.833 3.156,2.031 0.313,0.198 10 false EL 0.802,1.833 1.115,2.031 0.313,0.198 10 false ER
*a Rear view of wire harness connector
(to Turn Signal Flasher Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I29-2 (FR) - Body ground Hazard warning switch off Below 1 V
Hazard warning switch on Alternating between 22 to 26 V and below 1 V
(60 to 120 times per minute)
Turn signal switch right turn position Alternating between 22 to 26 V and below 1 V
(60 to 120 times per minute)
I29-3 (LL) - Body ground Hazard warning switch off Below 1 V
Hazard warning switch on Alternating between 22 to 26 V and below 1 V
(60 to 120 times per minute)
Turn signal switch left turn position Alternating between 22 to 26 V and below 1 V
(60 to 120 times per minute)
I29-5 (ER) - Body ground Turn signal switch neutral position 18 V or higher
Turn signal switch right turn position Below 1 V
I29-6 (EL) - Body ground Turn signal switch neutral position 18 V or higher
Turn signal switch left turn position Below 1 V


If the result is not as specified, replace the turn signal flasher assembly.