Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR
RM25T0E _55 Steering _029923 STEERING GEAR / LINKAGE _0136924 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 44110 1.FIX POWER STEERING GEAR ASSEMBLY

a.
C312193N01
0.781,0.99 1.198,0.719 true 0.49,0.927 0.948,1.125 0.458,0.198 10 false SST

Fix the power steering gear assembly on SST and clamp SST in a vise.

SST
09630-00014  (09631-00142)


Hide 44108 2.REMOVE SIDE COVER SUB-ASSEMBLY

a.

Remove the lock nut and cross shaft adjusting screw seal washer.


b.

Remove the 4 bolts.


c.
C312194

Screw in the sector shaft adjusting screw until the cover comes off.


Hide 44111 3.REMOVE CROSS SHAFT

a.
C312195

Using a plastic-faced hammer, tap on the cross shaft end and pull out the cross shaft.


Hide 44154 4.REMOVE POWER PISTON PLUNGER GUIDE NUT

a.
C312196

Using a 10 mm hexagon wrench, remove the power piston plunger guide nut.


b.

Remove the power piston plunger compression spring, power piston plunger and power piston plunger guide.


c.

Remove the O-ring from power piston plunger guide nut.


Hide 44120 5.REMOVE VALVE ASSEMBLY (WITH BALL NUT)

a.

Remove the 4 bolts.


b.
C312197N01
1.521,1.344 0.979,0.406 true 0.688,0.281 1.146,0.479 0.458,0.198 10 false SST

Using SST, turn the shaft clockwise to disconnect the valve assembly (with ball nut) from power steering gear housing.

SST
09616-00011  


c.
C312198C01
1.917,0.885 2.583,0.51 true 1.469,0.854 0.719,0.542 true 2.625,0.438 2.938,0.594 0.313,0.156 10 false *a 0.542,0.438 0.854,0.594 0.313,0.156 10 false *b
*a Power piston nut
*b Valve housing


Hold the power piston nut with your thumb so it cannot move, then with draw out the valve assembly (with ball nut).

NOTICE:

Ensure that the power piston nut does not come off the worm shaft.



d.

Remove the 2 O-rings from the power steering gear housing.


e.

Remove the O-ring from the valve housing of the valve assembly (with ball nut).


Hide 44107A 6.REMOVE POWER STEERING GEAR HOUSING NEEDLE ROLLER BEARING

a.
C312203

Using a screwdriver, pry out the power steering housing oil seal.


b.

Using snap ring pliers, remove the power steering gear housing hole snap ring.


c.

Remove the power steering gear housing ring, power steering gear housing ring ("Teflon" Ring) and O-ring.


d.
C312204N01
2.448,1.583 2.854,1.135 2.854,1.135 2.406,1.313 true 0.813,1.167 1.219,0.719 1.219,0.719 0.792,0.938 true 1.25,0.615 1.708,0.813 0.458,0.198 10 false SST 2.896,1.063 3.354,1.26 0.458,0.198 10 false SST

Using SST, press in the power steering gear housing needle roller bearing (lower).

SST
09950-60010  (09951-00350, 09951-00420, 09952-06010)
09950-70010  (09951-07100)


e.

Using SST, press out the power steering gear housing needle roller bearing (lower) and steering gear housing needle roller bearing (upper).

SST
09950-60010  (09951-00350, 09951-00420, 09952-06010)
09950-70010  (09951-07100)


Hide 44114A 7.REMOVE POWER PISTON NUT RING ("TEFLON" RING)

a.
C312600C01
1.698,1.156 2.073,1.615 true 2.104,1.604 2.417,1.76 0.313,0.156 10 false *a
*a Power piston nut


Using a screwdriver, remove the power piston nut ring ("Teflon" Ring) and O-ring.

NOTICE:

Be careful not to damage the power piston nut.



Hide 44105C 8.REMOVE VALVE BODY HOUSING UNION SEAT

a.
C312211

Using a screw extractor, remove the 2 valve body housing union seats.

NOTICE:
·

Do not allow any shards into the port.

·

In order to prevent shards, forcefully push down on the screw extractor, and then turn a very small amount to the left to pull out the valve body housing union sheet.

·

If the screw extractor is too small, the valve assembly port will be damaged.



HINT:

The valve body housing union seat has an inner diameter of 6 mm.



Hide 45357 9.REMOVE SECTOR SHAFT ADJUSTING SCREW

a.
C312201

Using a chisel and hammer, remove the lock nut stake.


b.
C312202N01
1.073,1.156 1.531,1.302 true 0.74,1.073 1.198,1.271 0.458,0.198 10 false SST

Using SST, remove the lock nut.

SST
09630-00014  (09631-00051)