Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR
RM25T0E _55 Steering _029923 STEERING GEAR / LINKAGE _0136924 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 44110 1.INSTALL POWER STEERING GEAR ASSEMBLY

a.

Install the power steering gear assembly with the 4 bolts and 4 nuts.

Torque:
127 N*m (1295 kgf*cm, 94 ft.*lbf)


b.
C312587C01
2.333,0.354 2.646,0.51 0.313,0.156 10 true *a
*a Torque Wrench Fulcrum Length


Connect the steering gear steering gear outlet return tube and pressure feed tube assembly.

Torque:
Specified tightening torque:

44.1 N*m (450 kgf*cm, 33 ft.*lbf)


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.1811 in.)) + torque wrench (fulcrum length of 255 mm (10.0394 in.)): 39.5 N*m (403 kgf*cm, 29 ft.*lbf)




Hide 44251 2.CONNECT PITMAN ARM

a.
C312190C01
1.25,1.042 0.906,0.615 0.906,0.615 1.604,1.063 true 1.813,0.948 2.333,0.573 true 1.854,1.698 2.333,1.906 true 0.729,0.521 1.042,0.677 0.313,0.156 10 false *a 2.375,1.854 2.688,2.01 0.313,0.156 10 false *2 2.375,0.458 2.688,0.615 0.313,0.156 10 false *1
*1 Cloth shaft
*2 Pitman arm
*a Matchmark


Align the matchmarks to the pitman arm and cloth shaft.


b.

Install the spring washer and nut.

Torque:
195 N*m (1988 kgf*cm, 144 ft.*lbf)


Hide 45203 3.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

a.
C312191C01
1.958,1.177 2.24,0.729 2.24,0.729 2.021,1.219 true 2.25,0.573 2.563,0.771 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks on the No. 2 steering intermediate shaft sub-assembly and power steering gear assembly.


b.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


c.

Tighten the 2 bolts of the steering sliding yoke.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 45636B 4.INSTALL INTERMEDIATE LINK JOINT PROTECTOR

a.

Install the intermediate link joint protector with the bolt.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)


Hide 53737B 5.INSTALL FRONT FENDER APRON SEAL LH

a.

Install the front fender apron LH with the 3 clips.


Hide 6.INSTALL FRONT WHEEL

Hide 7.ADD POWER STEERING FLUID

Hide 9.INSPECT POWER STEERING FLUID LEAK