Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY(for Model Code #J71 Series)
RM25T0E _58 Vehicle Interior _029930 SEAT _0138318 REAR NO. 1 SEAT ASSEMBLY(for Model Code #J71 Series) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for Model Code #J71 Series)  DISASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seat frame may injure your hands.


PROCEDURE

Hide 72694 1.REMOVE REAR SEAT CUSHION LOCK COVER

HINT:

Use the same procedure for the other side.


a.
B382428

Remove the 2 screws and rear seat cushion lock cover.


Hide 72660A 2.REMOVE REAR SEAT CUSHION SUPPORT ASSEMBLY

HINT:

Use the same procedure for the other side.


a.
B382429

Remove the 2 bolts.


b.

Detach the clamp and disconnect the No. 2 fold seat lock control cable assembly as shown in the illustration and remove the rear seat cushion support assembly.

B382430


Hide 73350 3.REMOVE REAR CENTER SEAT LAP TYPE BELT ASSEMBLY

Hide 73390 4.REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH

Hide 73380 5.REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH

Hide 6.REMOVE BENCH TYPE REAR SEATBACK ASSEMBLY

a.
B382433

Remove the 2 bolts and bench type rear seatback assembly.


Hide 78950 7.REMOVE NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY

a.
B384531C01
2.344,1.083 2.594,1.5 2.594,1.5 2.844,1.5 true 2.885,1.427 3.198,1.583 0.313,0.156 10 false *1
*1 Fastening Tape


Detach the fastening tape and open the bench type rear seatback cover.


b.
B384565

Remove the 6 hog rings.


c.
B384532C01
1.188,1.635 0.76,1.375 true 2.604,0.313 2.073,0.354 true 1.885,0.281 2.198,0.438 0.313,0.156 10 false *1 0.573,1.281 0.885,1.438 0.313,0.156 10 false *1
*1 Fastening Tape


Detach the 2 pieces of fastening tape.


d.
B382436

Remove the screw and No. 1 fold seat stopper band assembly.


Hide 71955A 8.REMOVE REAR SEAT HEADREST SUPPORT

a.
B382439

Remove the 4 hog rings.


b.
B384584

Detach the 8 claws and remove the 4 rear seat headrest supports.


Hide 71931A 9.REMOVE REAR SEAT HEADREST SUPPORT

a.
B382580

Remove the 12 hog rings.


b.
B376400

Detach the 8 claws and remove the 4 rear seat headrest supports.


Hide 71077B 10.REMOVE BENCH TYPE REAR SEATBACK COVER

a.

Remove the bench type rear seatback cover from the bench type rear seatback pad.


Hide 71651B 11.REMOVE BENCH TYPE REAR SEATBACK PAD

NOTICE:
·

As the bench type rear seatback pad is affixed to the rear seatback frame sub-assembly, do not remove the bench type rear seatback pad from the rear seatback frame sub-assembly unless it is necessary to replace the bench type rear seatback pad. If the bench type rear seatback pad is removed from the rear seatback frame sub-assembly, make sure to replace the bench type rear seatback pad.

·

Perform the following only when replacing the bench type rear seatback pad or rear seatback frame sub-assembly.



a.
B384533C01
1.552,0.479 0.979,0.271 false 0.792,0.188 1.104,0.344 0.313,0.156 10 false *a
*a Adhesive Area


Detach the part of the bench type rear seatback pad attached with adhesive shown in the illustration, and remove the bench type rear seatback pad.


Hide 71663 12.REMOVE REAR LOWER SEATBACK PAD

NOTICE:
·

As the rear lower seatback pad is affixed to the rear seatback frame sub-assembly, do not remove the rear lower seatback pad from the rear seatback frame sub-assembly unless it is necessary to replace the rear lower seatback pad. If the rear lower seatback pad is removed from the rear seatback frame sub-assembly, make sure to replace the rear lower seatback pad.

·

Perform the following only when replacing the rear lower seatback pad or rear seatback frame sub-assembly.



a.
B384535C01
0.896,1.948 1.313,1.625 true 2.615,1.917 2.146,1.635 true 0.719,1.885 1.031,2.042 0.313,0.156 10 false *a 2.667,1.865 2.979,2.021 0.313,0.156 10 false *a
*a Adhesive Area


Detach the part of the rear lower seatback pad attached with adhesive shown in the illustration, and remove the rear lower seatback pad.


Hide 71651 13.REMOVE REAR NO. 1 SEATBACK PAD

NOTICE:
·

As the rear No. 1 seatback pad is affixed to the rear seatback frame sub-assembly, do not remove the rear No. 1 seatback pad from the rear seatback frame sub-assembly unless it is necessary to replace the rear No. 1 seatback pad. If the rear No. 1 seatback pad is removed from the rear seatback frame sub-assembly, make sure to replace the rear No. 1 seatback pad.

·

Perform the following only when replacing the rear No. 1 seatback pad or rear seatback frame sub-assembly.



a.
B384536C01
0.667,0.979 1.104,0.24 true 2.146,1.927 2.406,1.01 true 1.115,0.073 1.427,0.229 0.313,0.156 10 false *a 2,1.969 2.313,2.125 0.313,0.156 10 false *a
*a Adhesive Area


Detach the part of the rear No. 1 seatback pad attached with adhesive shown in the illustration, and remove the rear No. 1 seatback pad.


Hide 72604 14.REMOVE REAR SEATBACK LOCK SUB-ASSEMBLY LH

a.
B384530

Remove the bush from the rear seatback lock sub-assembly LH.


b.
B382468

Remove the 2 bolts.


c.
B382482

Remove the 2 screws and remove the rear seatback lock cover.


d.

Using a screwdriver, unstake the stake part of the rear seatback lock sub-assembly LH.

HINT:

Tape the screwdriver tip before use.


B384559C01
2,0.708 2.51,0.458 true 1.635,1.823 2.042,1.406 true 1.458,1.813 1.771,1.969 0.313,0.156 10 false *1 2.563,0.365 2.875,0.521 0.313,0.156 10 false *2
*1 Stake Part *2 Protective Tape



e.

Remove the screw and disconnect the No. 1 seat lock control cable assembly and remove the rear seatback lock sub-assembly LH.


Hide 72603 15.REMOVE REAR SEATBACK LOCK SUB-ASSEMBLY RH

HINT:

Use the same procedure for the LH side.


Hide 71324A 16.REMOVE REAR SEAT CUSHION

HINT:

Use the same procedure for the other side.


a.
B384538

Remove the screw and rear seat cushion.


Hide 79929 17.REMOVE FOLD SEAT LEG STOPPER FRAME

a.
B382477

Using a screwdriver, remove the 2 spring nuts.


b.

Remove the fold seat leg stopper frame and 4 washers.


Hide 71382A 18.REMOVE REAR SEAT CUSHION SET BRACKET LH

a.
B384576

Remove the bolt and rear seat cushion set bracket LH.


b.
B384537

Remove the bush from the rear seat cushion set bracket LH.


Hide 71381A 19.REMOVE REAR SEAT CUSHION SET BRACKET RH

HINT:

Use the same procedure for the LH side.


Hide 71033 20.REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

a.
B384539

Using a screwdriver, remove the 2 E-rings and 2 rear seat cushion leg pins and rear seat cushion leg sub-assembly.


Hide 78910 21.REMOVE NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY

a.
B382475

Detach the 9 pieces of fastening tape and open the bench type rear seat cushion cover.


b.
B384540C01
2.333,1.667 2.531,1.208 2.531,1.208 2.698,1.208 true 1.833,1.583 2.198,0.833 2.198,0.833 2.365,0.833 true 1.75,1.927 1.583,2.844 1.583,2.844 1.333,2.844 true 0.99,1.938 0.823,2.854 0.823,2.854 0.573,2.854 true 2.74,1.115 3.052,1.271 0.313,0.156 10 false *1 1.156,2.781 1.469,2.938 0.313,0.156 10 false *2 0.396,2.771 0.708,2.927 0.313,0.156 10 false *2 2.417,0.76 2.729,0.917 0.313,0.156 10 false *2
*1 Clamp A
*2 Clamp B


Remove the clamp A.


c.

Detach the 3 clamp B and disconnect the 2 fold seat lock control cable assemblies.


d.

Remove the 2 bolts and 2 fold seat lock control cable assemblies together with the rear seat lock release strap assembly.


e.
B384554

Loosen the nut and disconnect the No. 1 fold seat lock control cable assembly as shown in the illustration.


Hide 78920 22.REMOVE NO. 2 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY

a.
B384555

Loosen the nut and disconnect the No. 2 fold seat lock control cable assembly as shown in the illustration.


Hide 71075B 23.REMOVE BENCH TYPE REAR SEAT CUSHION COVER

a.
B382478

Remove the 22 hog rings.


b.
B382480

Remove the 6 hog rings and bench type rear seat cushion cover.


Hide 71611 24.REMOVE REAR SEAT CUSHION PAD

a.

Remove the rear seat cushion pad from the rear seat cushion frame sub-assembly.


Hide 25.REMOVE CLIP

a.
B384585

Detach the 3 claws and remove the 3 clips from the rear seat cushion frame sub-assembly.