Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY(for Model Code #J71 Series) › 2014.08–2016.08
RM25T0E _58 Vehicle Interior _029930 SEAT _0138318 REAR NO. 1 SEAT ASSEMBLY(for Model Code #J71 Series) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for Model Code #J71 Series)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seat frame may injure your hands.


HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS


PROCEDURE

Hide 1.INSTALL CLIP

a.

Attach the 3 claws to install the 3 clips to the rear seat cushion frame sub-assembly.


Hide 71611 2.INSTALL REAR SEAT CUSHION PAD

a.

Install the rear seat cushion pad to the bench type rear seat cushion frame sub-assembly.


Hide 71075B 3.INSTALL BENCH TYPE REAR SEAT CUSHION COVER

a.

Set the bench type rear seat cushion cover in place.


b.
B382481C01
1.75,2.844 2,2.083 2,2.083 2.167,2.083 false 2.188,2 2.5,2.156 0.313,0.156 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install 6 new hog rings.

NOTICE:
·

Be careful not to damage the bench type rear seat cushion cover.


·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the bench type rear seat cushion cover.




c.
B382479C01
1.844,2.885 2.01,2.135 2.01,2.135 2.177,2.135 false 2.208,2.052 2.521,2.208 0.313,0.156 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install 22 new hog rings to the bench type rear seat cushion cover.

NOTICE:
·

Be careful not to damage the bench type rear seat cushion cover.


·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the bench type rear seat cushion cover.




Hide 78920 4.INSTALL NO. 2 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY

a.
B384557

Connect the No. 2 fold seat lock control cable assembly as shown in the illustration.


b.

Tighten the nut.


Hide 78910 5.INSTALL NO. 1 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY

a.
B384556

Connect the No. 1 fold seat lock control cable assembly as shown in the illustration.


b.

Tighten the nut.


c.
B384540C01
2.333,1.667 2.531,1.208 2.531,1.208 2.698,1.208 true 1.833,1.583 2.198,0.833 2.198,0.833 2.365,0.833 true 1.75,1.927 1.583,2.844 1.583,2.844 1.333,2.844 true 0.99,1.938 0.823,2.854 0.823,2.854 0.573,2.854 true 2.74,1.115 3.052,1.271 0.313,0.156 10 false *1 1.156,2.781 1.469,2.938 0.313,0.156 10 false *2 0.396,2.771 0.708,2.927 0.313,0.156 10 false *2 2.417,0.76 2.729,0.917 0.313,0.156 10 false *2
*1 Clamp B
*2 Clamp A


Install the 2 fold seat lock control cable assemblies together with the rear seat lock release strap assembly with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.

Attach the 3 clamp B to connect the 2 fold seat lock control cable assemblies.


e.

Install the clamp A.


f.

Attach the 9 pieces of fastening tape to close the bench type rear seat cushion cover.


Hide 71033 6.INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY

a.

Install the rear seat cushion leg sub-assembly with the 2 rear seat cushion leg pins and 2 new e-rings.


Hide 71382A 7.INSTALL REAR SEAT CUSHION SET BRACKET LH

a.

Install the bush to the rear seat cushion set bracket LH.


b.

Install the rear seat cushion set bracket LH with the bolt.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 71381A 8.INSTALL REAR SEAT CUSHION SET BRACKET RH

HINT:

Use the same procedure for the LH side.


Hide 79929 9.INSTALL FOLD SEAT LEG STOPPER FRAME

a.
B384564

Temporarily install the fold seat leg stopper frame and 4 washers.


b.
B384558C01
0.885,1.76 1,1.417 true 0.406,1.781 0.542,1.396 true 0.438,1.25 0.229,0.844 true 2.5,0.75 2.188,0.667 true 0.719,3.167 0.833,2.823 true 0.063,0.708 0.375,0.865 0.313,0.156 10 false *1 0.302,1.833 0.615,1.99 0.313,0.156 10 false *2 0.792,1.802 1.104,1.958 0.313,0.156 10 false *3 2,0.583 2.313,0.74 0.313,0.156 10 false *4 0.615,3.177 0.927,3.333 0.313,0.156 10 false *a
*1 Spring Nut
*2 12 mm Socket Wrench
*3 Extension Bar
*4 Plastic-faced Hammer
*a Groove


Set a new spring nut, 12 mm socket wrench and extension bar as shown in the illustration.


c.

Using a plastic-faced hammer, tap the extension bar to insert the spring nut into the groove and install the fold seat leg stopper frame.

HINT:

Use the same procedure for the other side.



Hide 71324A 10.INSTALL REAR SEAT CUSHION

HINT:

Use the same procedure for the other side.


a.

Install the rear seat cushion with screw.


Hide 72604 11.INSTALL REAR SEATBACK LOCK SUB-ASSEMBLY LH

a.

Connect the No. 1 seat lock control cable assembly with the screw.

B384560C01
4.656,1.833 5.073,1.417 true 4.479,1.844 4.792,2 0.313,0.156 10 false *1
*1 Stake Part - -



b.

Using pliers, stake the stake part of the rear seatback lock sub-assembly LH.


c.

Install the rear seatback lock cover with the 2 screws.


d.

Install the rear seatback lock sub-assembly LH with the 2 bolts.

Torque:
52.2 N*m (532 kgf*cm, 39 ft.*lbf)


e.

Install the bush to the rear seatback lock sub-assembly LH.


Hide 72603 12.INSTALL REAR SEATBACK LOCK SUB-ASSEMBLY RH

HINT:

Use the same procedure for the LH side.


Hide 71651 13.INSTALL REAR NO. 1 SEATBACK PAD

NOTICE:
·

As the rear No. 1 seatback pad is affixed to the rear seatback frame sub-assembly, do not remove the rear No. 1 seatback pad from the rear seatback frame sub-assembly unless it is necessary to replace the rear No. 1 seatback pad. If the rear No. 1 seatback pad is removed from the rear seatback frame sub-assembly, make sure to replace the rear No. 1 seatback pad.

·

Perform the following only when replacing the rear No. 1 seatback pad or rear seatback frame sub-assembly.



a.

When reusing the rear seatback frame sub-assembly:

i.
B384536C01
0.667,0.979 1.104,0.24 true 2.146,1.927 2.406,1.01 true 1.115,0.073 1.427,0.229 0.313,0.156 10 false *a 2,1.969 2.313,2.125 0.313,0.156 10 false *a
*a Adhesive Area


Remove any adhesive remaining in the area shown in the illustration.



b.

Apply adhesive to the rear seatback frame sub-assembly in the location shown in the illustration.


c.

Install 2 new rear No. 1 seatback pads to the rear seatback frame sub-assembly.


Hide 71663 14.INSTALL REAR LOWER SEATBACK PAD

NOTICE:
·

As the rear lower seatback pad is affixed to the rear seatback frame sub-assembly, do not remove the rear lower seatback pad from the rear seatback frame sub-assembly unless it is necessary to replace the rear lower seatback pad. If the rear lower seatback pad is removed from the rear seatback frame sub-assembly, make sure to replace the rear lower seatback pad.

·

Perform the following only when replacing the rear lower seatback pad or rear seatback frame sub-assembly.



a.

When reusing the rear seatback frame sub-assembly:

i.
B384535C01
0.896,1.948 1.313,1.625 true 2.615,1.917 2.146,1.635 true 0.719,1.885 1.031,2.042 0.313,0.156 10 false *a 2.667,1.865 2.979,2.021 0.313,0.156 10 false *a
*a Adhesive Area


Remove any adhesive remaining in the area shown in the illustration.



b.

Apply adhesive to the rear seatback frame sub-assembly in the location shown in the illustration.


c.

Install 2 new rear lower seatback pads to the rear seatback frame sub-assembly.


Hide 71651B 15.INSTALL BENCH TYPE REAR SEATBACK PAD

NOTICE:
·

As the bench type rear seatback pad is affixed to the rear seatback frame sub-assembly, do not remove the bench type rear seatback pad from the rear seatback frame sub-assembly unless it is necessary to replace the bench type rear seatback pad. If the bench type rear seatback pad is removed from the rear seatback frame sub-assembly, make sure to replace the bench type rear seatback pad.

·

Perform the following only when replacing the bench type rear seatback pad or rear seatback frame sub-assembly.



a.

When reusing the rear seatback frame sub-assembly:

i.

Remove any adhesive remaining in the area shown in the illustration.

B384534C01
5.969,0.833 6.448,0.625 false 0.896,1.396 1.313,1.458 false 0.979,0.635 1.323,0.417 false 0.688,1.313 1,1.469 0.313,0.156 10 false *a 6.5,0.542 6.813,0.698 0.313,0.156 10 false *a 0.802,0.604 1.115,0.76 0.313,0.156 10 false *a 4.021,0.052 4.177,0.25 0.156,0.198 10 false A 4.031,1.615 4.323,1.781 0.292,0.167 10 false A 0.833,0.063 1.604,0.26 0.771,0.198 10 false A - A
*a Adhesive Area - -
V100135

Front Side - -




b.

Apply adhesive to the rear seatback frame sub-assembly in the location shown in the illustration.


c.

Install a new bench type rear seatback pad to the rear seatback frame sub-assembly.


Hide 71077B 16.INSTALL BENCH TYPE REAR SEATBACK COVER

a.

Install the bench type rear seatback cover to the bench type rear seatback pad.


Hide 71931A 17.INSTALL REAR SEAT HEADREST SUPPORT

a.

Attach the 8 claws to install the 4 rear seat headrest supports.


b.
B382579C01
1.833,2.833 2,2.083 2,2.083 2.25,2.083 false 2.271,2.01 2.583,2.167 0.313,0.156 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install the 12 new hog rings.

NOTICE:
·

Be careful not to damage the bench type rear seatback cover.


·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the bench type rear seatback cover.




Hide 71955A 18.INSTALL REAR SEAT HEADREST SUPPORT

a.

Attach the 8 claws to install the 4 rear seat headrest supports.


b.
B384561C01
2.125,3.885 2.25,3.083 2.25,3.083 2.5,3.083 false 2.552,3 2.865,3.156 0.313,0.156 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install the 2 new hog rings.

NOTICE:
·

Be careful not to damage the bench type rear seatback cover.


·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the bench type rear seatback cover.




Hide 78950 19.INSTALL NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY

a.

Install the No. 1 fold seat stopper band assembly with the screw.


b.

Attach the 2 pieces of fastening tape.


c.
B384562C01
1.792,2.667 2.083,1.833 2.083,1.833 2.333,1.833 false 2.375,1.76 2.688,1.917 0.313,0.156 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install new 6 hog rings.

NOTICE:
·

Be careful not to damage the bench type rear seatback cover.


·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the bench type rear seatback cover.




d.

Attach the fastening tape to close the bench type rear seatback cover.


Hide 20.INSTALL BENCH TYPE REAR SEATBACK ASSEMBLY

a.

Install the bench type rear seatback assembly with the 2 bolts.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 73390 21.INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH

Hide 73380 22.INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH

Hide 73350 23.INSTALL REAR CENTER SEAT LAP TYPE BELT ASSEMBLY

Hide 72660A 24.INSTALL REAR SEAT CUSHION SUPPORT ASSEMBLY

HINT:

Use the same procedure for the other side.


a.

Attach the clamp to connect the No. 2 fold seat lock control cable assembly as shown in the illustration.

B384563


b.

Install the rear seat cushion support assembly together with the rear seat 3 point type belt assembly and rear center lap type belt assembly with the 2 bolts.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)


Hide 72694 25.INSTALL REAR SEAT CUSHION LOCK COVER

HINT:

Use the same procedure for the other side.


a.

Install the rear seat cushion lock cover with 2 screws.