Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM › 2014.08–2016.08
RM25T0E _58 Vehicle Interior _029925 THEFT DETERRENT / KEYLESS ENTRY _0138323 IMMOBILISER SYSTEM U

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  TERMINALS OF ECU  


CHECK TRANSPONDER KEY AMPLIFIER


B203482E09
3.5,0.177 3.823,0.396 0.323,0.219 3.563,0.208 3.99,0.448 0.427,0.24 10 false L28

a.

Disconnect the L28 transponder key amplifier connector.


b.

Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
L28-7 (AGND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -


c.

Reconnect the L28 transponder key amplifier connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Tester Connection Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
L28-1 (VC5) - L28-7 (AGND) Input L-R - W-B Power source No key in ignition key cylinder Below 1 V -
Key inserted in ignition key cylinder 4.6 to 5.4 V
L28-4 (CODE) - L28-7 (AGND) Output L-B - W-B Demodulated signal of key code data No key in ignition key cylinder Below 1 V -
Key inserted in ignition key cylinder Pulse generation
(See waveform 1)
L28-5 (TXCT) - L28-7 (AGND) Input R-Y - W-B Key code output signal No key in ignition key cylinder Below 1 V -
Key inserted in ignition key cylinder Pulse generation
(See waveform 2)


e.

Inspect using an oscilloscope.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B255093E03
0.09,1.688 0.434,1.832 0.344,0.145 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection L28-4 (CODE) - L28-7 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder


ii.
B255094E03
0.102,1.691 0.435,1.836 0.333,0.146 10 GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection L28-5 (TXCT) - L28-7 (AGND)
Tool Setting 2 V/DIV., 10 ms./DIV.
Condition Key inserted in ignition key cylinder




CHECK TRANSPONDER KEY ECU ASSEMBLY


B255101N08
3.458,0.219 3.833,0.438 0.375,0.219 3.563,0.25 3.833,0.417 0.271,0.167 10 false L30

a.

Disconnect the L30 transponder key ECU assembly connector.


b.

Measure the resistance and voltage according to the value(s) in the table below.

HINT:

Measure the values on the wire harness side with the connector disconnected.


Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
L30-1 (+B) - L30-16 (GND) Input P - W-B Battery Always 11 to 14 V +B
L30-2 (IG) - L30-16 (GND) Input B-Y - W-B Ignition switch signal Ignition switch off Below 1 V IG SW
Ignition switch ON 11 to 14 V
L30-3 (KSW) - L30-16 (GND) Input B-R - W-B Unlock warning switch signal No key in ignition key cylinder 10 kΩ or higher
·

B2780

·

Key SW


Key inserted in ignition key cylinder Below 1 Ω
L30-7 (CTY) - L30-16 (GND) Input B-W - W-B Front door courtesy light switch (for Driver Side) Driver door closed 10 kΩ or higher -
Driver door open Below 1 Ω
L30-16 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -


c.

Reconnect the L30 transponder key ECU assembly connector.


d.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
L30-8 (IND) - L30-16 (GND) Output G-R - W-B Security indicator signal Immobiliser system set Pulse generation Immobiliser
Immobiliser system unset Below 1 V
L30-9 (D) - L30-16 (GND) Input/Output W - W-B DLC3 communication Without communication Below 1 V -
During communication Pulse generation
L30-14 (VC5) - L30-5 (AGND) Output L-R - W-B Transponder key amplifier power source No key in ignition key cylinder Below 1 V -
Key inserted in ignition key cylinder 4.6 to 5.4 V
L30-15 (CODE) - L30-5 (AGND) Input L-B - W-B Transponder key amplifier communication signal No key in ignition key cylinder Below 1 V -
Key inserted in ignition key cylinder Pulse generation
(See waveform 1)
L30-4 (TXCT) - L30-5 (AGND) Output R-Y - W-B Transponder key amplifier communication signal No key in ignition key cylinder Below 1 V -
Key inserted in ignition key cylinder Pulse generation
(See waveform 2)
L30-12 (EFII) - L30-16 (GND) Input G - W-B ECM input signal Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
Pulse generation
-
L30-13 (EFIO) - L30-16 (GND) Output G-Y - W-B ECM output signal Ignition switch off Below 1 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 4)


e.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B255093E03
0.09,1.688 0.434,1.832 0.344,0.145 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection L30-15 (CODE) - L30-5 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Key inserted in ignition key cylinder


ii.
B255094E03
0.102,1.691 0.435,1.836 0.333,0.146 10 GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection L28-5 (TXCT) - L28-7 (AGND)
Tool Setting 2 V/DIV., 10 ms./DIV.
Condition Key inserted in ignition key cylinder


iii.

Waveform 3 (Reference)

B253467C07
1.583,1.198 1.979,1.479 0.396,0.281 10 false GND 2.198,1.292 2.5,1.531 0.302,0.24 10 false *a 2.75,1.292 3.063,1.542 0.313,0.25 10 false *b
*a Approximately 160 ms *b Approximately 510 ms


Measurement Condition
Item Content
Tester Connection L30-12 (EFII) - L30-16 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


iv.

Waveform 4 (Reference)

B253466C07
1.594,1.198 2.052,1.438 0.458,0.24 10 false GND 3.531,1.323 3.896,1.625 0.365,0.302 10 false *a 4.135,1.323 4.427,1.563 0.292,0.24 10 false *b
*a Approximately 160 ms *b Approximately 510 ms


Measurement Condition
Item Content
Tester Connection L30-13 (EFIO) - L30-16 (GND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 1GR-FE)


A182253E11
2.5,0.594 2.948,0.865 0.448,0.271 5.573,0.583 6.021,0.854 0.448,0.271 2.594,0.656 2.885,0.813 0.292,0.156 10 false C39 5.719,0.646 6.177,0.844 0.458,0.198 10 false I84

a.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item / DTC
I84-10 (IMO) - C39-81 (E1) Output G - BR Transponder key ECU assembly communication output Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
-
I84-11 (IMI) - C39-81 (E1) Input G-Y - BR Transponder key ECU assembly communication input Ignition switch off Below 1 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 3 (Reference)

B253467C07
1.583,1.198 1.979,1.479 0.396,0.281 10 false GND 2.198,1.292 2.5,1.531 0.302,0.24 10 false *a 2.75,1.292 3.063,1.542 0.313,0.25 10 false *b
*a Approximately 160 ms *b Approximately 510 ms


Measurement Condition
Item Content
Tester Connection I84-10 (IMO) - C39-81 (E1)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 4 (Reference)

B253466C07
1.594,1.198 2.052,1.438 0.458,0.24 10 false GND 3.531,1.323 3.896,1.625 0.365,0.302 10 false *a 4.135,1.323 4.427,1.563 0.292,0.24 10 false *b
*a Approximately 160 ms *b Approximately 510 ms


Measurement Condition
Item Content
Tester Connection I84-11 (IMI) - C39-81 (E1)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal




CHECK ECM (for 1VD-FTV)


A163584E04
2.396,0.188 2.906,0.5 0.51,0.313 2.396,0.188 2.906,0.5 0.51,0.313 5.531,0.188 6.042,0.5 0.51,0.313 2.521,0.26 2.823,0.438 0.302,0.177 10 false C39 5.667,0.271 5.938,0.479 0.271,0.208 10 false A29

a.

Measure the voltage and check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item / DTC
A29-10 (IMO) - C39-81 (E1) Output G - BR Transponder key ECU assembly communication output Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 1)
-
A29-11 (IMI) - C39-81 (E1) Input G-Y - BR Transponder key ECU assembly communication input Ignition switch off Below 1 V -
Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal Pulse generation
(See waveform 2)
-


b.

Using an oscilloscope, check the waveform.

NOTICE:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 3 (Reference)

B253467C07
1.583,1.198 1.979,1.479 0.396,0.281 10 false GND 2.198,1.292 2.5,1.531 0.302,0.24 10 false *a 2.75,1.292 3.063,1.542 0.313,0.25 10 false *b
*a Approximately 160 ms *b Approximately 510 ms


Measurement Condition
Item Content
Tester Connection A29-10 (IMO) - C39-81 (E1)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal


ii.

Waveform 4 (Reference)

B253466C07
1.594,1.198 2.052,1.438 0.458,0.24 10 false GND 3.531,1.323 3.896,1.625 0.365,0.302 10 false *a 4.135,1.323 4.427,1.563 0.292,0.24 10 false *b
*a Approximately 160 ms *b Approximately 510 ms


Measurement Condition
Item Content
Tester Connection A29-11 (IMI) - C39-81 (E1)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal