Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM › 2014.08–2017.09
RM25T0E _58 Vehicle Interior _029925 THEFT DETERRENT / KEYLESS ENTRY _0138323 IMMOBILISER SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM  Security Indicator Light Does not Blink  


DESCRIPTION

The transponder key ECU assembly blinks the security indicator light combination meter assembly when the immobiliser is set (no key is in the ignition key cylinder).

WIRING DIAGRAM

B236153E02
3.406,1.552 3.865,1.75 0.458,0.198 10 false L25 4.875,2.24 7.156,2.583 2.281,0.344 10 false Transponder Key ECU Assembly 0.938,1.917 3.219,2.26 2.281,0.344 10 false Combination Meter Assembly 3.406,1.01 3.865,1.208 0.458,0.198 10 false L26 3.458,0.844 3.917,1.042 0.458,0.198 10 false 23 3.458,1.375 3.917,1.573 0.458,0.198 10 false 15 3.125,1.448 3.583,1.646 0.458,0.198 10 false ES 1.24,1.271 3.521,1.615 2.281,0.344 10 false Security Indicator Light 3.115,0.917 3.573,1.115 0.458,0.198 10 false LP 4.698,0.896 5.156,1.094 0.458,0.198 10 false 8 4.938,1.01 5.396,1.208 0.458,0.198 10 false IND 4.875,2.094 7.156,2.438 2.281,0.344 10 false L30

CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly is replaced, refer to Service Bulletin.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (SECURITY INDICATOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Immobiliser or Main Body / Active Test.


e.

Perform the Active Test according to the display on the GTS.

Body Electrical > Immobiliser > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Security Indicator Security indicator light ON/OFF -
Body Electrical > Immobiliser > Active Test
Tester Display
Security Indicator
50004 260 1
OK:

Security indicator light can be turned on and off using the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

2.INSPECT SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY)
2.INSPECT SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY)
a.
B236154C01
1.458,0.948 1.813,1.198 0.354,0.25 1.604,3.083 1.958,3.333 0.354,0.25 1.302,2.396 1.063,1.917 false 2.99,3.406 2.615,3.99 false 1.521,0.99 1.979,1.188 0.458,0.198 10 false L26 1.688,3.125 2.146,3.323 0.458,0.198 10 false L25 1.375,2.344 1.833,2.542 0.458,0.198 10 false LP 3.031,3.344 3.427,3.542 0.396,0.198 10 false ES 0.083,0.063 0.542,0.26 0.458,0.198 10 false *a
*a Component without harness connected
(Combination Meter Assembly)


Remove the security indicator light (combination meter assembly).

Click hereVehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>REMOVAL


b.

Apply battery voltage between the terminals of the combination meter assembly, and check that the security indicator light illuminates.

OK:
Measurement Condition Specified Condition
Battery positive (+) → L26-23 (LP)
Battery negative (-) → L25-15 (ES)
Security indicator light illuminates.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) - TRANSPONDER KEY ECU ASSEMBLY AND BODY GROUND)

NG

REPLACE SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (SECURITY INDICATOR LIGHT (COMBINATION METER ASSEMBLY) - TRANSPONDER KEY ECU ASSEMBLY AND BODY GROUND)
a.

Disconnect the L25 and L26 security indicator light (combination meter assembly) connectors.


b.

Disconnect the L30 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L30-8 (IND) - L26-23 (LP) Always Below 1 Ω
L25-15 (ES) - Body ground Always Below 1 Ω
L30-8 (IND) or L26-23 (LP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR