Home › Vehicle Exterior › MIRROR (EXT) › OUTER MIRROR SWITCH
RM25T0E _59 Vehicle Exterior _029938 MIRROR (EXT) _0138353 OUTER MIRROR SWITCH G

MIRROR (EXT)  OUTER MIRROR SWITCH  INSPECTION  


PROCEDURE

Hide 84870A 1.INSTALL OUTER MIRROR SWITCH ASSEMBLY

a.
E271522C02
0.844,1.667 1.333,1.667 true 2.073,0.948 2.563,0.948 true 2.094,3.74 2.094,4 2.094,4 2.458,4 true 1.969,3.74 1.969,4.156 1.969,4.156 2.344,4.156 true 1.854,3.719 1.854,4.281 true 1.615,3.74 1.615,4 1.615,4 1.271,4 true 1.74,3.75 1.74,4.167 1.74,4.167 1.531,4.167 true 1.49,3.594 1.5,3.094 1.5,3.094 1.198,3.094 true 1.385,3.604 1.385,3.229 1.385,3.229 0.656,3.229 true 2.594,0.875 2.906,1.031 0.313,0.156 10 false *1 0.677,1.583 0.99,1.74 0.313,0.156 10 false *2 0.438,2.708 0.75,2.865 0.313,0.156 10 false *a 1.083,3.01 1.24,3.208 0.156,0.198 10 false E 0.531,3.146 0.688,3.344 0.156,0.198 10 false B 1.052,3.917 1.292,4.115 0.24,0.198 10 false M+ 1.198,4.083 1.583,4.292 0.385,0.208 10 false MLH 1.781,4.302 2.25,4.479 0.469,0.177 10 false MLV 2.375,4.094 2.896,4.271 0.521,0.177 10 false MRV 2.5,3.917 2.938,4.094 0.438,0.177 10 false MRH
*1 Mirror Select Switch
*2 Mirror Surface Adjust Switch
*a Component without harness connected
(Outer Mirror Switch Assembly)


Inspect the mirror select switch and mirror surface adjust switch.

i.

Select "L" on the mirror select switch.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (MLV) - 8 (B)
6 (M+) - 7 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
4 (MLV) - 7 (E)
6 (M+) - 8 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
5 (MLH) - 8 (B)
6 (M+) - 7 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
5 (MLH) - 7 (E)
6 (M+) - 8 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.


iii.

Select "R" on the mirror select switch.


iv.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (MRV) - 8 (B)
6 (M+) - 7 (E)
UP Pressed Below 1 Ω
Not pressed 10 kΩ or higher
3 (MRV) - 7 (E)
6 (M+) - 8 (B)
DOWN Pressed Below 1 Ω
Not pressed 10 kΩ or higher
2 (MRH) - 8 (B)
6 (M+) - 7 (E)
LEFT Pressed Below 1 Ω
Not pressed 10 kΩ or higher
2 (MRH) - 7 (E)
6 (M+) - 8 (B)
RIGHT Pressed Below 1 Ω
Not pressed 10 kΩ or higher


If the result is not as specified, replace the outer mirror switch assembly.