Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL › 2014.08–2016.08
RM25T0E _54 Brake _029916 BRAKE SYSTEM (OTHER) _0138391 BRAKE PEDAL N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL  ADJUSTMENT  


PROCEDURE

Hide 1.CHECK AND ADJUST BRAKE PEDAL HEIGHT

a.
C210999C01
0.74,2.229 1.448,2.229 1.448,2.229 1.667,1.365 false 0.781,2.531 1.594,2.531 1.594,2.531 1.844,1.385 false 2.885,1.604 2.51,1.604 2.51,1.604 2.5,1.156 false 0.573,2.146 0.885,2.344 0.313,0.198 10 false *1 0.625,2.438 0.938,2.635 0.313,0.198 10 false *2 2.813,3.76 3.125,3.958 0.313,0.198 10 false *a 2.938,1.51 3.25,1.708 0.313,0.198 10 false *3
*1 Push Rod
*2 Lock Nut
*3 Stop Light Switch
*a Pedal Height


Check the pedal height.

Standard pedal height from floor panel:
Item Specified Condition
for LHD 177.9 to 187.9 mm (7.01 to 7.39 in.)
for RHD 175.9 to 185.9 mm (6.93 to 7.31 in.)



b.

Adjust the pedal height.

i.

Disconnect the connector from the stop light switch.


ii.

Loosen the stop light switch lock nut and turn the switch so that the pedal has free play.


iii.

Loosen the push rod clevis lock nut.


iv.

Adjust the pedal height by turning the push rod.

Standard pedal height from floor panel:
Item Specified Condition
for LHD 177.9 to 187.9 mm (7.01 to 7.39 in.)
for RHD 175.9 to 185.9 mm (6.93 to 7.31 in.)



v.

Tighten the lock nut.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


vi.
C312694C01
1.354,0.896 1.354,0.302 1.354,0.302 1.688,0.302 false 0.677,1.781 0.99,1.979 0.313,0.198 10 false *a 1.729,0.229 2.042,0.427 0.313,0.198 10 false *1
*1 Stop Light Switch Lock Nut
*a 0.5 and 2.4 mm (0.0197 and 0.0944 in.)


Turn the stop light switch so that its protrusion is between 0.5 and 2.4 mm (0.0197 and 0.0944 in.), and then tighten the lock nut.

Torque:
Specified tightening torque:

16.7 N*m (170 kgf*cm, 12 ft.*lbf)


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.1811 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 14.3 N*m (146 kgf*cm, 11 ft.*lbf)




vii.

Connect the stop light switch connector.


viii.

Without depressing the brake pedal, check that the stop light does not illuminate. If it illuminates, adjust the brake pedal height again.


ix.

Depress the brake pedal 5 to 10 mm (0.197 to 0.393 in.), and check that the stop light comes on. If the stop light does not turn on, adjust the brake pedal height again.



Hide 2.CHECK BRAKE PEDAL FREE PLAY

a.
C111306C02
2.146,1.5 2.396,1.708 0.25,0.208 10 *a
*a Pedal Free Play


Stop the engine. Depress the pedal several times until there is no vacuum in the booster. Then release the pedal.


b.

Depress the pedal until resistance is felt.


c.

Check the pedal free play by measuring the distance between the position in the previous step and the pedal's released position.

Standard pedal free play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


If the free play is not as specified, check the switch clearance in the next step.

If the free play is as specified, proceed to the Check Brake Pedal Reserve Distance procedure.


d.

Check the switch clearance.

Standard stop light switch clearance:

0.5 and 2.4 mm (0.0197 and 0.0944 in.)


If the clearance is not as specified, reinstall the switch and recheck the pedal free play.

If the clearance is as specified, troubleshoot the brake system and proceed to the Check Brake Pedal Reserve Distance procedure.


Hide 3.CHECK BRAKE PEDAL RESERVE DISTANCE

a.

Release the parking brake lever. Stop the engine and depress the brake pedal several times until there is no more vacuum left in the booster.


b.

Depress the pedal and check the pedal reserve distance.

i.

Depress the pedal with a force of 300 N (31 kgf, 67 lbf).


ii.

Measure the distance between the pedal and floor panel.

Standard pedal reserve distance:
Item Specified Condition
for LHD without ABS More than 128 mm (5.04 in.)
for LHD with ABS More than 136 mm (5.35 in.)
for RHD without ABS More than 127 mm (4.99 in.)
for RHD with ABS More than 136 mm (5.35 in.)


If the result is not as specified, troubleshoot the brake system.

HINT:

Check the brake pedal reserve distance at the same location as that used when checking the brake pedal height.