Home › Brake › BRAKE SYSTEM (OTHER) › LOAD SENSING PROPORTIONING VALVE › 2014.08–2017.09
RM25T0E _54 Brake _029916 BRAKE SYSTEM (OTHER) _0138397 LOAD SENSING PROPORTIONING VALVE G

BRAKE SYSTEM (OTHER)  LOAD SENSING PROPORTIONING VALVE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 47900 1.CHECK LOAD SENSING PROPORTIONING VALVE ASSEMBLY

C283545C03
2.156,0.563 2.469,0.719 0.313,0.156 10 false *a
*a Weight


a.

Set the vehicle to its curb weight.


b.

Place weights (as necessary) on the rear deck until the rear axle load is as shown below.

Standard Rear Axle Load:
Vehicle Type Rear Brake Specified Condition
GRJ71 Drum 12258 N (1250 kgf, 2755.8 lbf)
GRJ76
HZJ71
HZJ76
GRJ78 Drum 14710 N (1500 kgf, 3306.9 lbf)
HZJ71 Disc 11278 N (1150 kgf, 2535.9 lbf)
GRJ76 Disc 12750 N (1300 kgf, 2866.3 lbf)
HZJ76
VDJ76 Drum 12258 N (1250 kgf, 2755.8 lbf)
Disc 12750 N (1300 kgf, 2866.3 lbf)
GRJ79 Drum/Disc 14710 N (1500 kgf, 3306.9 lbf)
HZJ78
HZJ79
VDJ78 Drum/Disc 14710 N (1500 kgf, 3306.9 lbf)
VDJ79 Drum/Disc 14710 N (1500 kgf, 3306.9 lbf)


NOTICE:
·

Be sure that the vehicle is on a level surface before starting the procedure.

·

When placing the weights on the vehicle, first place the weights so that the total is approximately 60 kg (132 lb) more than the specification. Then remove weights as necessary to adjust the load.




c.
C160057N01
0.813,0.354 1.208,0.354 false 2.344,0.323 2.76,0.323 false 0.51,0.281 0.969,0.479 0.458,0.198 10 false SST 2.813,0.24 3.271,0.438 0.458,0.198 10 false SST

Install SST and bleed air from the brake system.

SST
09709-29018  


d.
C160058N01
0.417,0.354 0.729,0.354 false 2.354,0.344 2.698,0.344 false 0.115,0.271 0.573,0.469 0.458,0.198 10 false SST 2.75,0.271 3.135,0.49 0.385,0.219 10 false SST

Raise the front brake fluid pressure to 9000 kPa (91.8 kgf/cm2, 1305 psi) by depressing the brake pedal, and measure the rear brake fluid pressure.

Standard Rear Brake Fluid Pressure:
Rear Brake Specified Condition
Drum 5082 to 6258 kPa (51.9 to 63.8 kgf/cm2, 737 to 907 psi)
Disc 7502 to 8678 kPa (76.5 to 88.4 kgf/cm2, 1088 to 1258 psi)


HINT:

The pedal should not be depressed twice or released while the specified pressure is being set. Read the value of the rear pressure after adjusting and holding the specified fluid pressure for 2 seconds.


If necessary, adjust the load sensing proportioning valve.


Hide 47900 2.ADJUST LOAD SENSING PROPORTIONING VALVE ASSEMBLY

a.
C210996C01
2.26,1.448 2.802,1.448 true 2.719,1.833 2.208,1.833 2.208,1.833 2.052,1.604 true 2.844,1.365 3.156,1.563 0.313,0.198 10 false *1 2.771,1.75 3.083,1.948 0.313,0.198 10 false *2 0.969,1.469 1.125,1.667 0.156,0.198 10 false A
*1 Lock Nut
*2 Adjusting Nut


Adjust the length of the No. 2 load sensing spring shackle.

Loosen the lock nut, and then adjust the length of the No. 2 shackle.

When the rear brake fluid pressure is below the standard pressure, lengthen length A.

When the rear brake fluid pressure is higher than the standard pressure, shorten length A.

Standard Initial Length (A):

78 mm (3.07 in.)


Standard Length (A) after Adjustment:

72 to 84 mm (2.84 to 3.30 in.)


HINT:

The rear fluid pressure changes according to the table below by turning the adjusting nut.


Standard Rear Brake Fluid Pressure:
Model Rear Brake For 1 Turn of Lock Nut
GRJ71 Drum 187 kPa (1.9 kgf/cm2, 27 psi)
HZJ71
HZJ76
HZJ71 Disc 239 kPa (2.4 kgf/cm2, 35 psi)
HZJ76
GRJ76 Drum 187 kPa (1.9 kgf/cm2, 27 psi)
Disc 239 kPa (2.4 kgf/cm2, 35 psi)
GRJ79 Drum 187 kPa (1.9 kgf/cm2, 27 psi)
Disc 239 kPa (2.4 kgf/cm2, 35 psi)
VDJ76 Drum 187 kPa (1.9 kgf/cm2, 27 psi)
Disc 239 kPa (2.4 kgf/cm2, 35 psi)
GRJ78 Drum 187 kPa (1.9 kgf/cm2, 27 psi)
HZJ78
HZJ79
HZJ78 Disc 239 kPa (2.4 kgf/cm2, 35 psi)
HZJ79
VDJ78 Drum 187 kPa (1.9 kgf/cm2, 27 psi)
Disc 239 kPa (2.4 kgf/cm2, 35 psi)
VDJ79 Drum 187 kPa (1.9 kgf/cm2, 27 psi)
Disc 239 kPa (2.4 kgf/cm2, 35 psi)



b.

Tighten the adjusting nut and lock nut.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


c.
C160060

If the pressure cannot be adjusted by the No. 2 shackle, raise or lower the valve body.

When the pressure is below the standard pressure, lower the load sensing valve assembly.

When the pressure is higher than the standard pressure, raise the load sensing valve assembly.


d.

Tighten the 2 nuts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


e.

Adjust the length of the No. 2 shackle again. If the rear fluid pressure cannot be adjusted, check the valve body.


Hide 3.CHECK VALVE BODY

a.
C160061

Install the valve body in the uppermost position.

HINT:

When the brakes are applied, the position will move down by approximately 0.8 mm (0.0315 in.). Even at this time, the piston should not make contact with or move the load sensing spring.


If the result is not as specified, replace the load sensing valve assembly.


b.
C160058N01
0.417,0.354 0.729,0.354 false 2.354,0.344 2.698,0.344 false 0.115,0.271 0.573,0.469 0.458,0.198 10 false SST 2.75,0.271 3.135,0.49 0.385,0.219 10 false SST

Using SST, check the rear brake pressure.

SST
09709-29018  

Standard Pressure:
Rear Brake Front Brake Pressure Rear Brake Pressure
Drum 981 kPa (10.0 kgf/cm2, 142 psi) 981 kPa (10.0 kgf/cm2, 142 psi)
4903 kPa (50.0 kgf/cm2, 711 psi) 1569 to 2354 kPa (16.0 to 24.0 kgf/cm2, 228 to 341 psi)
9807 kPa (100.0 kgf/cm2, 1422 psi) 2697 to 3677 kPa (27.5 to 37.5 kgf/cm2, 391 to 533 psi)
Disc 1961 kPa (20.0 kgf/cm2, 284 psi) 1961 kPa (20.0 kgf/cm2, 284 psi)
4903 kPa (50.0 kgf/cm2, 711 psi) 2452 to 3236 kPa (25.0 to 33.0 kgf/cm2, 356 to 469 psi)
9807 kPa (100.0 kgf/cm2, 1422 psi) 3825 to 4805 kPa (39.0 to 49.0 kgf/cm2, 555 to 696 psi)


If the result is not as specified, replace the load sensing proportioning valve.